PDA

View Full Version : piasini



Pages : [1] 2

ducatisti
10th June, 2011, 06:39 PM
Anyone used the piasini master clone ?

Reports ?

BigTee
12th June, 2011, 12:32 PM
Yes and it works perfectly :top:

wiseman
13th June, 2011, 12:09 AM
how much is clone? orig is well expensive

z786
13th June, 2011, 12:38 AM
i think its still around the 2 grand mark mate

wiseman
13th June, 2011, 12:49 AM
hi z mate,
i think i heard the other day it was around the ?1800 mark. You can do evo`s with it but why not buy the Openport cable , its well cheap and its an original tool :-)

z786
13th June, 2011, 01:03 AM
1800, 2000, not far off :)
you forgot postage :D

you can never have too many tools lol

bazare
13th June, 2011, 08:58 AM
piasini is a very good tool, but in europe it will pay off pretty hard. But if you want to cover the cars other tuners don't then this is the real thing.

Stanton
13th June, 2011, 10:01 AM
Or Alientech K-tag :)

Tactrix OP2 is great for the price, cant fault it....but something which offers j-tag comms is always going to be in a different league.

jovime
13th June, 2011, 12:56 PM
K-TAG will don't see the light until 2-3 weeks more, was planned to be realeased last month... Payed it already, so it should arrive in short time :)

z786
13th June, 2011, 02:17 PM
how does any here remap toyota petrol engines? and the normal diesel ones?

soundnavigator
14th June, 2011, 11:49 AM
Piasini clone ... there is such ?

VAGR666
14th June, 2011, 11:54 AM
piasini master with all plugins it must be something like 15 000 or more.

clone is about the numbers others talked here.

tactrix is a great tool but only for a small number of cars, piasini has a huge list compared.

BR

bazare
14th June, 2011, 11:54 AM
yes piasini master clone - price between 1800-2200

VAGR666
14th June, 2011, 11:56 AM
yes piasini master clone - price between 1800-2200

slave a litle bit cheaper :)

VAGR666
14th June, 2011, 11:58 AM
K-tag is kind of green yet, but it will be a good tool.



K-TAG will don't see the light until 2-3 weeks more, was planned to be realeased last month... Payed it already, so it should arrive in short time :)

z786
14th June, 2011, 12:10 PM
any clones for the kessv2 and k-tag yet VAGR666?

VAGR666
14th June, 2011, 12:24 PM
any clones for the kessv2 and k-tag yet VAGR666?


i have heard something about it, but think they aren't yet ready for selling....

bazare
14th June, 2011, 12:37 PM
kess v2 clone is in testing phase. About k-tag i don't know.

VAGR666
14th June, 2011, 07:20 PM
Anyone used the piasini master clone ?

Reports ?


mine works very good, i like it a lot... with all the soft version i have.


Best Regards

gzk
15th June, 2011, 02:50 PM
mine works very good, i like it a lot... with all the soft version i have.


Best Regards

CAN YOU GIVE ME SOME INFO IN PM
NEED TO BUY ONE CLONE TOO

VAGR666
15th June, 2011, 05:43 PM
CAN YOU GIVE ME SOME INFO IN PM
NEED TO BUY ONE CLONE TOO

i can give all info you want, but this thread is for impression, not selling.


Best Regards

VAGR666
24th June, 2011, 10:08 PM
just received the new soft version :) . great job once again ...

lolooo1981
24th June, 2011, 10:28 PM
Is this interface work on all japan car ?
Maybe work on Mazda RX-8?
Thanks for info i need.

faiscamix
24th June, 2011, 10:34 PM
With new soft works perfect. Nice pcb quality and nice cables, i'm very glad with the interface.

BR

VAGR666
25th June, 2011, 12:10 AM
Is this interface work on all japan car ?
Maybe work on Mazda RX-8?
Thanks for info i need.


it works with many japan cars, but others also.

yes, it does maxda RX8 .


Best Regards

wiseman
25th June, 2011, 04:25 PM
Tactrix OpenPort Cable does work on some mazda`s not sure about the RX8, it does some japanese Cars But mainly Subaru and Mitsubishi,basically any Subaru ECU based on a HC16, or SH-2 processor and any Mitsubishi ECU based on a H8, SH-2, or M32r processor.
Its Very affordable for an Orginal tool aswell

lolooo1981
25th June, 2011, 04:33 PM
Tactrix OpenPort Cable does work on some mazda`s not sure about the RX8, it does some japanese Cars But mainly Subaru and Mitsubishi,basically any Subaru ECU based on a HC16, or SH-2 processor and any Mitsubishi ECU based on a H8, SH-2, or M32r processor.
Its Very affordable for an Orginal tool aswell

I am interest by read ECU of 1L3 rotative.
thanks

Marmes
25th June, 2011, 09:29 PM
Piasini does RX8 By obd2 ;) Also good in original flavour :P

lolooo1981
25th June, 2011, 10:19 PM
Piasini does RX8 By obd2 ;) Also good in original flavour :P

Maybe you point me on a new interface to buy :D

Best regards.

faiscamix
26th June, 2011, 04:38 PM
Piasini clone ... there is such ?
Everythig is such lol

yewkhip
22nd November, 2011, 04:13 AM
for the clone piasini master, does it come with all car driver files include RX8? or we have to online purchase the specific driver files?

eprommazza
24th November, 2011, 10:43 AM
example of piasini china

how read boot c 167 mb ecu 2.1

regards

moky
24th November, 2011, 10:47 AM
so piasini chinese work fine eprommazza?

eprommazza
24th November, 2011, 10:48 AM
so piasini chinese work fine eprommazza?

if you see up ???

also if no work i repair !!!

regards

moky
24th November, 2011, 10:50 AM
ok :D

thx

zecas
25th November, 2011, 02:11 AM
if you see up ???

also if no work i repair !!!

regards

good job
keep us updated on how this chinese clone works

unfortunally i see this forum is contaminated with many false information by sellers and wannabees

faiscamix
25th November, 2011, 07:56 AM
For all doubts about this tool.

nicamarcos
25th November, 2011, 03:54 PM
if you see up ???

also if no work i repair !!!

regards

Hey Gennaro!, where you was??? :)

eprommazza
25th November, 2011, 06:02 PM
Hey Gennaro!, where you was??? :)

always online every day
work

hello

eprommazza
4th December, 2011, 02:02 PM
hello,

for who as looking for piasini 4.1 master clone, here it is with good price.


regards.

but where are the moderators? seems to be a crap ....
This ebay?

soundnavigator
13th December, 2011, 03:55 PM
Someone have PDF instruction for Nissan Almera/Primera 1.8 115 HP with Hitachi ECU ?

Best regards.

Elettra
13th December, 2011, 06:37 PM
Hello everyone,

I buy a piassini device, but i can't open the rom file I read.

i buy it as master, but I get it slave.

someone can exaplin me what i must do ?

i contact again the company i buy it from, but seams they don't know what they are telling me.

who can help me ???

BR

Elettra

gzk
14th December, 2011, 03:12 AM
http://www.chinaautodiag.com/download/piasini.zip
perhaps it can help
need activation code to work i'm looking for the keygen

nicole99wu
14th December, 2011, 10:50 AM
my friend use a piasini slave, cheaper than master

Elettra
14th December, 2011, 11:40 AM
http://www.chinaautodiag.com/download/piasini.zip
perhaps it can help
need activation code to work i'm looking for the keygen

I have the same folder into the CD-rom i have receive from them.

but I contact them today, and they told me they don't know what to do ?!?!?!

are we sure they are the producer this device???

thanks anyway for try to help me.

now they told me to wait reaply from engineers

let's see....

BR

Elettra

gzk
14th December, 2011, 03:43 PM
I have the same folder into the CD-rom i have receive from them.

but I contact them today, and they told me they don't know what to do ?!?!?!

are we sure they are the producer this device???

thanks anyway for try to help me.

now they told me to wait reaply from engineers

let's see....

BR

Elettra

ASK FOR A REFUND WITHOUT THE LICENSE YOU CAN'T USE IT

Stanton
14th December, 2011, 08:41 PM
They will just be resellers

Elettra
15th December, 2011, 08:24 AM
ASK FOR A REFUND WITHOUT THE LICENSE YOU CAN'T USE IT


they told me they sell all like this, and they don't know how to do it.

now I try to get back my money...

BR

Elettra

tomtom0785
15th December, 2011, 08:55 AM
good luck m8

ducatisti
15th December, 2011, 08:42 PM
they told me they sell all like this, and they don't know how to do it.

now I try to get back my money...

BR

Elettra


You have to run Ghenwid inside the folder and send them the code. They should send licence that you put in folder. Then you can use master.

Maybe somone here can help you with licence.

moky
22nd December, 2011, 09:15 PM
did you find solution for serial problem of slaves chinese?

ecu-master
23rd December, 2011, 10:07 PM
Serial Suite Piasini Engineering V4.1 MASTER (http://www.ecutool.com/Serial-Suite-Piasini-Engineering-V41-MASTER_8029.html)
is this the same tool and has any one bought from ecu tool

bulardas
5th January, 2012, 12:08 PM
The clone slave vs master, are different internally or just the software is different?

eprommazza
5th January, 2012, 01:46 PM
The clone slave vs master, are different internally or just the software is different?

only software is different...

chris_e36_328
6th January, 2012, 10:25 AM
Wouldn't the firmware of the interface be different though?

eprommazza
6th January, 2012, 04:13 PM
Wouldn't the firmware of the interface be different though?

no! no!!
need only reg file software for pc and this is master

best regards

bulardas
6th January, 2012, 04:17 PM
Serial Suite Piasini Engineering V4.1 MASTER (http://www.ecutool.com/Serial-Suite-Piasini-Engineering-V41-MASTER_8029.html)
is this the same tool and has any one bought from ecu tool

There is also a software 4.1 for piasini for master. It is working well? Can be used with an original tool and not break it?

ecu-master
6th January, 2012, 09:48 PM
so if i buy clone slave can i make it master

blackpirate
6th January, 2012, 10:18 PM
so if i buy clone slave can i make it master
yes.
and i can help!:P

ecu-master
7th January, 2012, 11:04 PM
Thanks so I am going to buy this one
Serial Suite Piasini Engineering V4.1 SLAVE (http://www.ecutool.com/Serial-Suite-Piasini-Engineering-V41-SLAVE_8028.html)
Is this ok be4 I buy
Don't want to wast money

J_amb_o
8th January, 2012, 02:18 AM
anyone sorted OBD?

ecu-master
8th January, 2012, 11:02 AM
anyone sorted OBD?
What is wrong with odb

chris_e36_328
8th January, 2012, 11:58 AM
I was under impression the clone piasini wasn't doing much in the OBD port department..

anyhow, can anyone recommend a flasher to do a 2.4 2004 honda accord?

ecu-master
8th January, 2012, 05:11 PM
I was under impression the clone piasini wasn't doing much in the OBD port department..

anyhow, can anyone recommend a flasher to do a 2.4 2004 honda accord?


so what can a original do that clone can not ? apart from updating

ducatisti
8th January, 2012, 07:16 PM
No one has succesfully read mazda 6 and others via obd with clone 4.1 software. Some peole say it work by bridging obd pins but its not confirmed. Only told by the sellers of the clones.

Can anyone confirm

Mulatre
11th January, 2012, 04:41 PM
Tried to read Mazda 6 via OBD2, piasini succesfully connected but can't login to download flash. Got Security error.

Then i've tried and successfully done it by Epifans MazdaEdit.

Mulatre
11th January, 2012, 04:44 PM
Only Piassini in JTAG mode can do Honda. Already done Civic with success. As far as i know ECU on Civic and Accrod are same.


I was under impression the clone piasini wasn't doing much in the OBD port department..

anyhow, can anyone recommend a flasher to do a 2.4 2004 honda accord?

soundnavigator
11th January, 2012, 06:49 PM
...

Then i've tried and successfully done it by Epifans MazdaEdit.

From where you buy Epifans MazdaEdit and for how ?

ducatisti
12th January, 2012, 01:59 AM
Only Piassini in JTAG mode can do Honda. Already done Civic with success. As far as i know ECU on Civic and Accrod are same.

Can piasini do any honda with renesas 32r processor ?

ducatisti
12th January, 2012, 02:00 AM
Tried to read Mazda 6 via OBD2, piasini succesfully connected but can't login to download flash. Got Security error.

Then i've tried and successfully done it by Epifans MazdaEdit.

Yes everyone is getting the security error with piasini. Apparently bridging some obd pins solves he problem according to the sellers but i think not.

blackpirate
12th January, 2012, 12:08 PM
From where you buy Epifans MazdaEdit and for how ?


from here

epifanSoftware | ecuEdit (http://www.epifansoft.com/)


from what ive heard its about 800-1000e!

cheers

Mulatre
12th January, 2012, 01:01 PM
Can piasini do any honda with renesas 32r processor ?

Don't know :( on what models can i found it?

Mulatre
12th January, 2012, 01:03 PM
Yes everyone is getting the security error with piasini. Apparently bridging some obd pins solves he problem according to the sellers but i think not.

Don't know how it can help to bypass security, if MazdaEdit read it without any problem and without any bridges. I'll try on next client and report.

blackpirate
28th February, 2012, 10:02 AM
From where you buy Epifans MazdaEdit and for how ?


from official website or you can buy a cracked version!:)

cheers

moky
28th February, 2012, 06:26 PM
blackpirate have you got solution to pass chinese piasini clone slave to master.Thx

chris_e36_328
11th March, 2012, 09:48 PM
Could someone share info as to most reliable source of the piasini flasher please. One needed now. Cheers

ducatisti
12th March, 2012, 10:40 AM
Last time I bought a euro clone was 1200 euro including all postage and 4.1 v2 safe internet connection.

Best money ever spent. I made that back about thirty times. Thanks piasini :)

chris_e36_328
12th March, 2012, 11:12 AM
yup, still looking.. anyone?

blackpirate
12th March, 2012, 11:14 AM
try carsung.net
cheers

jovime
12th March, 2012, 11:28 AM
I have one original PIASINI with all original cables and adapters (hardware is 100% original), sw is v4.1 MASTER (clone sw).

I'm selling it. Price by PM.

ducatisti
14th March, 2012, 01:17 AM
Pm sent . I'll take that.

moky
3rd April, 2012, 03:19 PM
someone got pdf for nissan Z 350 processor 7055 please?

Many thx

eprommazza
3rd April, 2012, 05:04 PM
someone got pdf for nissan Z 350 processor 7055 please?

Many thx

see it if ok

:playingball:

moky
3rd April, 2012, 05:11 PM
It's solved but thx eprommazza !

furburger
4th April, 2012, 11:27 PM
Has anyone used piasini on nissan navarra ? is it difficult ?!

Stanton
5th April, 2012, 03:37 AM
Yes. Not especially, 13 or 14 wires to to solder to the ecu pcb.

autotuning
5th April, 2012, 10:10 AM
I made a BDM type adaptor for mine
works perfect on Denso ECU's was well worth the effort.

furburger
5th April, 2012, 11:57 AM
I made a BDM type adaptor for mine
works perfect on Denso ECU's was well worth the effort.

That sounds ideal , what model years does it cover up to ?

chris_e36_328
5th April, 2012, 12:01 PM
Hi, please could anyone share mazda mzr 2.2 denso ecu pinout for piasini? many thanks, Chris

autotuning
5th April, 2012, 12:35 PM
That sounds ideal , what model years does it cover up to ?
i have used it on mazda and nissan up to 2010 so far but any denso with the same structure will be fine

furburger
5th April, 2012, 06:11 PM
And the 100ps Astra g or h , it has a denso , anyone tried the tool on this?

donesko
15th June, 2012, 06:06 PM
is it possible to reflash honda civic ep3 (type R), or only fn2
on list I see this:
2.0 16v 201 CV TypeR

Keihin

[Keihi-Honda][Renesas][SH7058][Checksum Honda]

peregrine
15th June, 2012, 09:57 PM
is it possible to reflash honda civic ep3 (type R), or only fn2
on list I see this:
2.0 16v 201 CV TypeR

Keihin

[Keihi-Honda][Renesas][SH7058][Checksum Honda]

Yes have done so several times!

donesko
16th June, 2012, 12:34 PM
Yes have done so several times!

youve done fn2 or ep3(2004)

peregrine
16th June, 2012, 07:05 PM
Both inclunding a US spec Si

peregrine
16th June, 2012, 07:08 PM
Quite often only one car is listed but if the ECU is the same you can still read and write it. Example to day I had a 1.3 16V lancer come in used the diagram for an Outlander 2.4 165 bhp

donesko
20th June, 2012, 06:18 PM
Both inclunding a US spec Si

over obd or on bench?
are there any manuals for piasini

donesko
22nd June, 2012, 09:38 AM
over obd or on bench?
are there any manuals for piasini

guess not.
Remap Civic FN2 ECU Remap - No Hondata required - Civinfo (http://www.civinfo.com/forum/engines-transmission/62147-civic-fn2-ecu-remap-no-hondata-required.html)

this is by the looks of that flat cable done with piasini?

peregrine
22nd June, 2012, 05:47 PM
Hi,

No manuals just info packs (PDF doc) for each ecu. If you have a clone you will need some good friends, if you have an ori you can contact tech support and they can help. With some ecu?s I just try. BTW I have an original Piasini Master.

peregrine
22nd June, 2012, 05:53 PM
Yes it is done by a Pisini tool pins are the same as the one I have. The pictures are for the read part the write part is on the back!

donesko
24th June, 2012, 09:09 AM
Both inclunding a US spec Si

one more question, what do you use to edit maps for civic?
can it be done with winols,swiftec or some specific software like uberdata for p28

jset
24th June, 2012, 11:34 AM
Hi to all
Y have a question
the original Slave piasini works with software v 4.1 of the clone master?

thnaks

peregrine
24th June, 2012, 08:36 PM
one more question, what do you use to edit maps for civic?
can it be done with winols,swiftec or some specific software like uberdata for p28

Winols & Map3D let me know if you ned the mod file I will give it to you (US spec Civic Si 2008) as it was done on the dayno. You can copy and past the changes with eather software.

kenancatli
31st July, 2012, 12:01 AM
hello piasini pinout
china clone this pinout on picture correctly??
which picture correctly?
best regards

dyc
31st July, 2012, 06:40 AM
these are ok for cloned device

kenancatli
31st July, 2012, 03:59 PM
Hello thanx dyc
China clone is good work fine dyc?
Best Regards

dyc
2nd August, 2012, 07:23 AM
Hello thanx dyc
China clone is good work fine dyc?
Best Regards

Yes work ok but try not make a mistake with connections in that case can be easy damaged

tehnosoftex
22nd August, 2012, 08:14 PM
these are ok for cloned device

Did anyone knows what are the pins from 1 to 20? For example if I want to connect to motorola mpc which are the whire I must connect , dsdi, dsdo, reset, sck?

Mulatre
31st August, 2012, 11:15 AM
Hi!

Bought Piasini China Clone from ecutool.com, but my FLash voltage (yellow wire) is 12v, must be 16v :(

Also, Plus (red wire) is 10v, must be 12v.

Support can't help me, can anybody tell me what resistors must be here:

eprommazza
31st August, 2012, 11:22 AM
:roflmao:Hi!

Bought Piasini China Clone from ecutool.com, but my FLash voltage (yellow wire) is 12v, must be 16v :(

Also, Plus (red wire) is 10v, must be 12v.

Support can't help me, can anybody tell me what resistors must be here:

can ask if can return back
maybe is better change
r32=1912 think 19,1 kohm
r33=2201 think 2200 ohm

http://www.vincenzov.net/tutorial/elettronica-di-base/resistenze/codice-SMD.htm
br

oep
2nd September, 2012, 11:17 PM
Mulatre u fixed it already?

Got one similar here, black pcb.
1) power red 11.20v max (should be 12v)
2) flash voltage yellow - goes to 13.00v max (should be 16v)

Need resistor values back of pcb r23,r27,r28,r30 and R32 R33 from LM output.

jolidj
3rd September, 2012, 05:02 PM
is possible to have pdf for piasini, Honda Acura 3.2TL , i dont have the pdf file.
thank you very much.

jolidj
3rd September, 2012, 05:57 PM
i have the voice , but dont have the pdf file for this.

Mulatre
4th September, 2012, 04:02 PM
Voltage is ok now, but still can't read ECUs :(

maxsek
4th September, 2012, 09:37 PM
hi friend can you have a pdf for connection my piasini to valeo s3000 clio rs 197cv.....help me thanks

Mulatre
5th September, 2012, 08:36 AM
You can find manuals here: http://www.digital-kaos.co.uk/forums/f173/piasini-manuals-277651/

Also for S3000 on last page.

jolidj
5th September, 2012, 05:25 PM
i have the voice , but dont have the pdf file for this.
this is my ecu is possible to have piasini pdf ore pinout for this ecu?
thanks.

jolidj
5th September, 2012, 05:34 PM
i have the voice , but dont have the pdf file for this.
this is my ecu is possible to have piasini pdf ore pinout for this ecu?
thanks.

oep
5th September, 2012, 09:05 PM
here is pinout

jolidj
5th September, 2012, 09:19 PM
thank you my friend. im so hepy.

oep
5th September, 2012, 11:06 PM
Any thoughts about voltage?

Mulatre
6th September, 2012, 01:52 PM
Same shit with voltage! :(

But my GND wire is black.

noze95
10th September, 2012, 02:16 PM
hi guy's i need software serial piasini clone v4.1
thkx

Holtek
16th September, 2012, 07:38 PM
Software Piasini Serisl Suite 4.1

OVERSPEED
19th September, 2012, 03:27 AM
another one with Voltage issues...

I conected and read about 10,8V in the two red (should be 12V) wires and 0V in yellow (should be 16v)... but the voltagem was dropping and dropping til reaches about 2,5Volts.

When I conect the 12V plug only Jtag became green

OVERSPEED
21st September, 2012, 12:59 AM
Well...

the problens:

1) LM is not beeing actived (pin 5 to ground) guess is a problem with T7, managed it grounding direct LM pin 5, now I have about 11,6V in 12V lines

If You have less than it you shold change R32 and/or R33 (look for LM data sheet) to somethng about 10x the low value.

2) Program 16V Wire, it didn?t work (guess it shall be enable only by software when needed, because I measure about 15V before FT1 or it?s something like the issue 1)

3) The major issue:

If I start the software and after plug OBD it enable all protocols (became green), And show ID, firmware and status.

but if I plug 12V charger only JTAG and Utilities keep green, all other becames gray and ID, firmware and status became "unknown" and piasini didn?t work more until I unplug 12V charger, USB, exit the program and start again.

Can someone point me some hint or direction ?


Dont worth to return back because of Brazil tax and shipping value.

matech
26th September, 2012, 08:24 PM
Mine arrived today, I'll check voltage and after that I'll try some r/w



PS: same voltage problems!

16V= 11V
12V= 2,5V

:-O

metrostar
4th October, 2012, 01:54 PM
Hi all,
I Piasini a clone that does not work.
I opened it and saw that a capacitor is disconnected from the board.
Can someone help me understand what kind of capacitor?
See attached photos.
thanks in advance

cp2010
4th October, 2012, 02:01 PM
inductor 100uH

nynhp
22nd October, 2012, 08:22 AM
can i use piasini to read a 2008 Jaguar XF 4.2 V8 Supercharged ?

mihaiservice
22nd October, 2012, 05:33 PM
hi
anyone have read 25P32 flash ? need the good one for master

many thx

matech
24th October, 2012, 04:51 PM
How do you check the voltage?

I'm testing with a mitsubishi protocol (ecu that need 16v programming voltage)

12v ok
16v=0,25v bad!

niwat_spp
24th October, 2012, 05:32 PM
hi
anyone have read 25P32 flash ? need the good one for master

many thx
yes i have read it. after flash its ok

mihaiservice
25th October, 2012, 10:07 AM
can you upload you flash ?
thx

mihaiservice
31st October, 2012, 03:05 PM
thx niwap_spp...already solved

OVERSPEED
31st October, 2012, 03:29 PM
Can someone post an picture of board with high quality to check the values ?

ducatisti
4th November, 2012, 07:30 PM
Well...

the problens:

1) LM is not beeing actived (pin 5 to ground) guess is a problem with T7, managed it grounding direct LM pin 5, now I have about 11,6V in 12V lines

If You have less than it you shold change R32 and/or R33 (look for LM data sheet) to somethng about 10x the low value.

2) Program 16V Wire, it didn?t work (guess it shall be enable only by software when needed, because I measure about 15V before FT1 or it?s something like the issue 1)

3) The major issue:

If I start the software and after plug OBD it enable all protocols (became green), And show ID, firmware and status.

but if I plug 12V charger only JTAG and Utilities keep green, all other becames gray and ID, firmware and status became "unknown" and piasini didn?t work more until I unplug 12V charger, USB, exit the program and start again.

Can someone point me some hint or direction ?


Dont worth to return back because of Brazil tax and shipping value.

I have same problem. With 12v plugged in it went grey and only j tag was green . what is problem ?

OVERSPEED
5th November, 2012, 11:58 PM
Didn?t had any progress with it... if you discover anything please inform !!!

ACDC
10th November, 2012, 03:42 PM
Anyone ever use a clone Piasini to read a Mazda 5 RF7N ECU? Really don't want to kill this ECU with it....it's probably impossible to find a second-hand ECU for it here, so I'm afraid a bit to try...

ivoo
10th November, 2012, 07:59 PM
Can someone post an picture of board with high quality to check the values ?
Here is photo of board.

pulsar2000
11th November, 2012, 12:16 AM
obdtools the uk site, No im not connected :>

piasini working Denso mazda 6, no issues, all green on Protocols., 12V
perfect read & Write. also cd i got with sw, had keygen,
no emails to activate, so far all good
if interested will post pic of board

ducatisti
11th November, 2012, 02:31 PM
obdtools the uk site, No im not connected :>

piasini working Denso mazda 6, no issues, all green on Protocols., 12V
perfect read & Write. also cd i got with sw, had keygen,
no emails to activate, so far all good
if interested will post pic of board

Was that by obd or on the bench ?

Does anyone know of a china clone that works flash voltage and k line without problem ?

pulsar2000
11th November, 2012, 03:24 PM
not obd, bench tune job

michael122
12th November, 2012, 11:04 AM
Solution for 16V :

- R41 0.2 Om
- R40 200 Om
- R43 820 Om
- L2 220 uH

For board as in post #140...

kennfeld
12th November, 2012, 11:48 AM
not obd, bench tune job

Not it work also on obd plug i use original cmdflash cable for obd ;)

ACDC
14th November, 2012, 03:27 PM
Got my Piasini yesterday, and I also have a problem with voltages. Managed to change some components according to michael122's instructions, and now I have about 16,4V on 16V line (yellow wire) and 11,4V on 12V line (red) but if there's a load on the 12V line, voltage falls back to about 10,5V. I don't really think that is enough, anyone got any more suggestions what to change?

ivoo
14th November, 2012, 06:08 PM
Got my Piasini yesterday, and I also have a problem with voltages. Managed to change some components according to michael122's instructions, and now I have about 16,4V on 16V line (yellow wire) and 11,4V on 12V line (red) but if there's a load on the 12V line, voltage falls back to about 10,5V. I don't really think that is enough, anyone got any more suggestions what to change?
Try change resistor R32 to 22kohm now is I think 19,1 kohm

ducatisti
14th November, 2012, 11:55 PM
Got my Piasini yesterday, and I also have a problem with voltages. Managed to change some components according to michael122's instructions, and now I have about 16,4V on 16V line (yellow wire) and 11,4V on 12V line (red) but if there's a load on the 12V line, voltage falls back to about 10,5V. I don't really think that is enough, anyone got any more suggestions what to change?

where are the problem clones comming from ?

obd2s.com was excellent :) my contacts had 5 last year and all were good

michael122
27th November, 2012, 12:03 PM
My solution for k-line :

I replaced the R23 and R28 to the resistors 39k and replaced by SI9241 .

I did not have in stock 9241, so I mounted the L9637 (according to datasheet) , and R21 replaced by 4.7 kOm to optimize L9376.
Now the K-line is working properly

ducatisti
29th November, 2012, 10:38 PM
I have same problem. With 12v plugged in it went grey and only j tag was green . what is problem ?

Update - i have found R8 is missing off my board. What does R8 do ?

michael122
2nd December, 2012, 08:05 AM
R8 - 10kOm
Pullup for programming interface LPC2368...

ducatisti
2nd December, 2012, 08:18 PM
R8 - 10kOm
Pullup for programming interface LPC2368...

Thanks

Will this explaine why when using flash voltage , the device does not communicate and then the green lights go grey like the power has been pulled ?

michael122
3rd December, 2012, 10:20 AM
Measure the supply voltage for ECU coming out from device .
R8 does not affect this.

ducatisti
6th December, 2012, 12:32 AM
i have 12 volts. The issue is when i hit connect. The lightss go grey like the usb cable has been disconnected ?

can anybody give me a link to buy two good working units ?

ducatisti
6th December, 2012, 12:33 AM
my euro clone bought 2 years ago has never had problems :)

dragger
7th December, 2012, 01:00 AM
Solution for 16V :

- R41 0.2 Om
- R40 200 Om
- R43 820 Om
- L2 220 uH

For board as in post #140...

Anyone tried it? is it working ?

ivoo
9th December, 2012, 05:38 PM
Anyone tried it? is it working ?
Yes solution from "michael122" is working, after replacement of parts I have around 16.3V.

Youneselm
9th December, 2012, 06:01 PM
its working like a charme

Babos
13th December, 2012, 09:41 AM
hi mates!
I have problem with feding in piasini clon whit out logo.
i tested wire +12V i have +14mV and wire +16V i have jumping feding +6v-+13v. How fix this problem?
Who know if i take +12V not to tool but other place i can working with this piasini? and if i take +16V to other place?

jolidj
29th December, 2012, 10:26 PM
friend is possible pin out pdf for yamaha T-max ecu?
serch this file for long time.thanks all.

popescovici11
6th January, 2013, 04:05 PM
please help with activation file for piasini master

yJZ3O4WGQaKK1xB7AnQcUucDSkk=

thanks

dyc
6th January, 2013, 05:42 PM
please help with activation file for piasini master

yJZ3O4WGQaKK1xB7AnQcUucDSkk=

thanks


check pm friend

nick22
7th January, 2013, 07:23 PM
Please help -activation file for piasini master

dMRvvKmLB2+6KLe5ArEi0pqF9em3Muu5

Thanks :)

wiseman
7th January, 2013, 07:43 PM
Please help -activation file for piasini master

dMRvvKmLB2+6KLe5ArEi0pqF9em3Muu5

Thanks :)
...................

donesko
8th January, 2013, 09:10 AM
one thing I dont understand, does piasini suite 4.1 includes Ford/Mazda ECU tool?
I see they sell this separatly for more than piasini alone

kennfeld
8th January, 2013, 01:05 PM
one thing I dont understand, does piasini suite 4.1 includes Ford/Mazda ECU tool?
I see they sell this separatly for more than piasini alone


it's not working on masters
it work only on official slave that piasini srl is master from

you need at least have a working v4.4 to have the obd mazda fiat working

chris_e36_328
18th January, 2013, 11:15 PM
Hi guys, has anyone tried piasini on a DCM3.5 before? cheers

Catalin_TCM
21st January, 2013, 03:16 PM
Piasini Clone can read/write Nissan NAVARA 2.5dci 140hp on OBD ? Ecu is DENSO D3

Stanton
21st January, 2013, 08:52 PM
Piasini Clone can read/write Nissan NAVARA 2.5dci 140hp on OBD ? Ecu is DENSO D3

No, neither can original.

maglaras
22nd January, 2013, 03:03 PM
I HAVE PROBLEM ON K LINE can you help me?
thank you

maglaras
22nd January, 2013, 09:44 PM
any help for k line i have problem

pbn
22nd January, 2013, 11:30 PM
:giveup:has anyone pdf for yamaha xt660 or mt660 please?
i have pdf for facer 2005, but the board its not the same! :hmmmm2:

mbtun
23rd January, 2013, 12:12 AM
Piasini Clone can read/write Nissan NAVARA 2.5dci 140hp on OBD ? Ecu is DENSO D3
you need some soldering to make it work

Mulatre
23rd January, 2013, 05:05 PM
Hi guys, has anyone tried piasini on a DCM3.5 before? cheers

WARNING!

Tried Piasini Portugal on Mercedes Delphi with Nexus JTAG MPC55xx, read ok, but writing locked ECU! :sleep:

It seems cloned software version 4.1 have no good working driver for MPC55xx. :reddy:

tehnosoftex
23rd January, 2013, 05:17 PM
can you send the connection from piasini with the nexus jtag? I want to try myself


Sent from my iPad using Tapatalk HD

kennfeld
23rd January, 2013, 06:55 PM
Piasini Clone can read/write Nissan NAVARA 2.5dci 140hp on OBD ? Ecu is DENSO D3


yes you can do with last version 4.4 contact support to get it !

Stanton
23rd January, 2013, 08:52 PM
Please post file read via OBD on Navara DCI.

Stanton
23rd January, 2013, 08:52 PM
Please post file read via OBD on Navara DCI.

BrunoPT
23rd January, 2013, 09:17 PM
errorrrr :)

Catalin_TCM
24th January, 2013, 02:24 PM
Soldering in ecu or in interface ? :)

gkoutsis
31st January, 2013, 12:15 PM
My solution for k-line :

I replaced the R23 and R28 to the resistors 39k and replaced by SI9241 .

I did not have in stock 9241, so I mounted the L9637 (according to datasheet) , and R21 replaced by 4.7 kOm to optimize L9376.
Now the K-line is working properly

Can you please explain how you used a L9637 in place of the SI9241? pinout is completely different.

Datasheet of L9637
http://www.microchips-tuning.com/pdf/L9637.pdf

Datasheet of SI9241
http://www.microchips-tuning.com/pdf/SI9241.pdf

I can only assume you used small cables and matched the pins to the new L9637 driver

Did you measure the SI9241 and found it dead? What if you replaced it with a working SI9241?

gkoutsis
31st January, 2013, 01:15 PM
Can you please confirm this?

LI and CS seem to have the same function as inputs but I am not 100% sure.
Fault and LO are both shutdown signals if conditions are not correct.

http://www.microchips-tuning.com/pdf/Replacement%20of%20SI9241%20by%20L9637.jpg

megasosio
31st January, 2013, 03:54 PM
I have a problem whit my piasini interface. Only read on bdm not for obd, Any whit this problem or is possible to repair.

Thanks for all.

moky
31st January, 2013, 08:31 PM
normal,piasini is not hardware for obd..

which car you test ?

megasosio
1st February, 2013, 11:11 AM
HI! thanks for the fast response. My piasini have a obd conector, and in the list have many cars. I test whit at least 12 cars on the list, ie. ,alfa 159 3.2, mazda 6 denso, and other 10 or 12 cars.
I think im a very very newbie... piasini not read in obd conector in cars??
Thanks for all.

moky
1st February, 2013, 11:53 AM
yes lot of cars don't work by obd ..

someone tested piasini from gocardiag? work fine?

I want to buy one wo work

Thx!

Roydnier
2nd February, 2013, 07:10 PM
Good morning everyone
I'm from Brazil and I just bought a clone and PIASINI'm with some doubts about it, could someone give me a little help?
msn: reparodecentral@hotmail.com
Skype: reprodecentral

veloseeped
2nd February, 2013, 10:52 PM
yes lot of cars don't work by obd ..

someone tested piasini from gocardiag? work fine?

I want to buy one wo work



I think that's impossible to buy Piasini 4.1 working over OBD.
This version should work only!!! with some Mazda/Ford ECU.
But "should" does not equal "work" :flybye:
I have original Piasini V4.1 master and it also not work over OBD.
I know it 100% because have insider info from P.

johan240
2nd February, 2013, 11:46 PM
please manual pdf for subaru tribeca 3.0 denso

Bosses
3rd February, 2013, 01:30 AM
Pinout volvo Denso 140,170 ps?
No big issue,google nada.
Do enyone know? i cant find any info on the net.
I find nothing,or i?m just stupid.

kennfeld
4th February, 2013, 01:31 PM
HI! thanks for the fast response. My piasini have a obd conector, and in the list have many cars. I test whit at least 12 cars on the list, ie. ,alfa 159 3.2, mazda 6 denso, and other 10 or 12 cars.
I think im a very very newbie... piasini not read in obd conector in cars??
Thanks for all.


obd work only on official tools that are slave from the piasini company

leolux
4th February, 2013, 02:04 PM
Hi,

can Piasini read and write the Nissan GT-R r35?

Leo

kennfeld
4th February, 2013, 06:36 PM
Hi,

can Piasini read and write the Nissan GT-R r35?

Leo

solution to read they cost about 2000 euro ex vat

kennfeld
4th February, 2013, 09:59 PM
I think that's impossible to buy Piasini 4.1 working over OBD.
This version should work only!!! with some Mazda/Ford ECU.
But "should" does not equal "work" :flybye:
I have original Piasini V4.1 master and it also not work over OBD.
I know it 100% because have insider info from P.


up to now only piasini official slave do obd you need a slave that christian is the master otherwise it do'nt work

veloseeped
5th February, 2013, 02:21 AM
can Piasini read and write the Nissan GT-R r35?


Yes, on ECUs with 7058 CPU.
Don't test piasini on new ECUs with 7059 CPU inside.

johan240
6th February, 2013, 08:57 PM
my piasini have 10v in red .

i conect de piasini to external suply of 16v and red have 11.9v

is correct is posible damage piasini or ecuS???

another cuestion how cable for boot ecus in piasini???

dariobmw
7th February, 2013, 02:05 PM
try to change the usb cable maybe faulty i have same prob with
gall2

e.t.
10th February, 2013, 12:42 PM
Hi

Today i test piasini on denso Opel Astra 1.7 cdti 125hp.
It Start Reading after 10s it stop and the green "select Car" are grey! Can someone help me? I Shows that there is now Connection

Tanks

kevfield
10th February, 2013, 03:26 PM
I read and write this type ecu no probs u must have bad contions or clone tool is not good.
Is your power supply good ???
Thanks kev

e.t.
10th February, 2013, 04:16 PM
I read and write this type ecu no probs u must have bad contions or clone tool is not good.
Is your power supply good ???
Thanks kev

Perhaps the power supply is the problem! I Test it again. But when i take off the power its not the same mistake

Where you buy your clone?

e.t.
10th February, 2013, 07:08 PM
I test it with other power supply but its the same probem.

Unkown USB is coming on windows

leolux
11th February, 2013, 05:57 AM
Yes, on ECUs with 7058 CPU.
Don't test piasini on new ECUs with 7059 CPU inside.

Hi thanks for info. With old one you have test read and write? it is only BDM or other soluton?

Leo

fodortms
15th March, 2013, 10:59 AM
I test it with other power supply but its the same probem.

Unkown USB is coming on windows

Hi!
The the first wire on the clone are the other side(red wire) than original !!!
The picture wrong! Sorry !
I have same problem with it! My cable are different, than this picture. My red wire are the other side than on the picture!
Check it your cable!
Br Tamas

radion2005
20th March, 2013, 08:32 PM
Can you please explain how you used a L9637 in place of the SI9241? pinout is completely different.

Datasheet of L9637
http://www.microchips-tuning.com/pdf/L9637.pdf

Datasheet of SI9241
http://www.microchips-tuning.com/pdf/SI9241.pdf

I can only assume you used small cables and matched the pins to the new L9637 driver

Did you measure the SI9241 and found it dead? What if you replaced it with a working SI9241?

Hello,
This solution works fine on my interface.
Thanks

kriseo
20th March, 2013, 09:46 PM
The problems with the cable 2x10 is serious. Lastday I made this picture and send it to the China company, no answer:)

motorsoftekb
6th May, 2013, 07:07 AM
Hello Comrads! Please help me to activate Piasini Master! :)

QGmZbl07Pp16DCYUW/22KA==

Regards, Igor

albertros
6th May, 2013, 09:39 AM
yes lot of cars don't work by obd ..

someone tested piasini from gocardiag? work fine?

I want to buy one wo work

Thx!

Hi
I bought mine from gocardiag. Silver box
Wont write S3000 renault reads ok.

uldinnsh
6th May, 2013, 09:27 PM
196847
motorsoftekb activate

kennfeld
6th May, 2013, 11:09 PM
Hi

Today i test piasini on denso Opel Astra 1.7 cdti 125hp.
It Start Reading after 10s it stop and the green "select Car" are grey! Can someone help me? I Shows that there is now Connection

Tanks
powersupply need several amp?res ...
mine is 5A

moky
6th May, 2013, 11:20 PM
Now we can have good euro piasini clone for 3xx euros..for those who know work on all this ecu..they just can help me to say : one concil pay 300 euros.. lot of people slashhh ecu with chinese clone (Me first) so be careful ...and after: 300 euros is ...hum ..too light :D

motorsoftekb
8th May, 2013, 04:37 PM
Thank you so much!! It work's!

LaraVAG
30th May, 2013, 07:26 PM
Need key: 8BSaBz3PPHTaNuvzbiw+3fMwSMY=

Thx in advance

autotuning
30th May, 2013, 07:40 PM
here it is enjoy
201406


Need key: 8BSaBz3PPHTaNuvzbiw+3fMwSMY=

Thx in advance

chipex10
1st June, 2013, 08:05 PM
Hi, pls licence for this ID QGvYEZVPVprD86c0
Regards

stevan
3rd June, 2013, 07:40 AM
HERE PIC OF PCB WITH ALL MARKINGS201959

autotuning
3rd June, 2013, 08:35 PM
here you go
202090

Hi, pls licence for this ID QGvYEZVPVprD86c0
Regards

Zmann
12th June, 2013, 01:50 PM
Hi, I'm looking for good pin description of the 20 pin plug, mine from the cd is incomplete. thanks

2xded
12th June, 2013, 02:12 PM
This can help you

Zmann
12th June, 2013, 02:22 PM
thanks, I have the same file in the cd that I think it's unclear, need more details especially to the jtag pins if possible.

Cipo
23rd June, 2013, 09:36 AM
Hello, I need a key. My id is : JC8aDB2wwTlug/kTT3UA2g==

Thank you

marsete
23rd June, 2013, 10:20 AM
Hello, I need a key. My id is : JC8aDB2wwTlug/kTT3UA2g==

Thank you
Hi friend,here your licence.Regards

xanubysx
20th July, 2013, 04:35 PM
Hi guy... please help, i need pinout for PIASINNI to car NISSAN Xtrail Denso 2.2dci year 2004 ... picture here...210001

e.t.
20th July, 2013, 05:25 PM
Hi!
The the first wire on the clone are the other side(red wire) than original !!!
The picture wrong! Sorry !
I have same problem with it! My cable are different, than this picture. My red wire are the other side than on the picture!
Check it your cable!
Br Tamas

Yes my cable is not the same like original piasini

You have the same problem?

Techhead
9th August, 2013, 01:10 PM
Hi, can someone help me with piasini connection pdf or connections for the ECU for Honda Civic EP3 2.0 TypeR?

BrunoPT
9th August, 2013, 05:06 PM
Hi, can someone help me with piasini connection pdf or connections for the ECU for Honda Civic EP3 2.0 TypeR?

Piasini Car LIST :) - > https://www.dropbox.com/s/j3mkgzqlndwfpjx/Cars_Piasini.zip

choro
29th August, 2013, 10:20 AM
hi friends need license.key
HW ID:ECC+yqGEJonGB8H8s9PtlA==
thanks

chris_e36_328
6th September, 2013, 07:15 PM
Hi all, has anyone got a piasini connection pdf for 2.0L petrol mazda 3 mitsubishi ECU? possibly same as 2.3 NA petrol. cheers

aassfour
7th September, 2013, 12:22 PM
hello need license for piasini
rHrzRp0N4sTXPjW1
anyone ? thx

LaraVAG
29th October, 2013, 03:19 PM
Hi, need key please

5LdRYsnkZmJq706MYjNXJb/6Tyc=

Thx in advance!

autotuning
29th October, 2013, 04:16 PM
227073 here you go

ker0sin
12th November, 2013, 11:01 PM
Hi, need key please

VNRvfXmStXLuPc9EFj2N2NN/VOY=

Thx in advance!

choro
13th November, 2013, 02:06 PM
Hi, need key please

ECC+ygG1mq3GB8H8f7SAKg==

Thx in advance!

waldi1979
13th November, 2013, 09:14 PM
Here you are.

atomiczen
8th May, 2014, 11:37 PM
license for straki007

name: straki

choro
10th June, 2014, 04:09 PM
KBWuCb2H0cKKCfczi2f4tg==
please help again

ysarius
10th June, 2014, 08:43 PM
activation for choro
name:choro

263308

Matador1340
10th June, 2014, 09:24 PM
Does any of you has a working k line? i have 3 of those clones and none of them has a working k line only j tag working.

OVERSPEED
11th June, 2014, 11:32 AM
Mine is working now, but I resolder practically all of elements that are related with powerline...

magnacin
13th June, 2014, 12:11 AM
Mine is working now, but I resolder practically all of elements that are related with powerline...

Can you please provide images?
Thanks

VAGR666
16th June, 2014, 10:42 AM
mine is working but it is a 4.3 EU clone

Best Regards

Matador1340
16th June, 2014, 09:36 PM
where did u get that i am looking all over the net please pm me the info

VAGR666
17th June, 2014, 10:32 AM
i had the 4.1 EU and received the upgrade maybe 2 months ago.


where did u get that i am looking all over the net please pm me the info

moky
25th August, 2014, 01:00 PM
hi all

I have a problem on piasini clone,read denso ecu,no problem,modify and flash ok


i read flash after and file is corrupted,read and write 100% ok 3 times.....


Someone ever seen this problem? (simple ecu 4D56)


original file attached


many thx!

steveeprom
25th August, 2014, 03:58 PM
Used Piassini Slave Original for sale! It is in perfect contition, it made only 4 ecus is like new.It can supported from piassini company to send you tune files,update are free!

steveeprom
31st January, 2015, 01:46 PM
I sell used slave Piassini with all wires like new.!! with piassini copmany support!! 1000 euro

Johnner
31st January, 2015, 01:47 PM
Steve,I'd stop posting for sale stuff,or else you're gonna be wearing a coat of grey !!!

jeremy96121
1st October, 2015, 10:05 AM
Hi all,
My piasini 4.3 is not working, i tried to use it on YFZ. But no ecu found. I think my problem is 12v (in fact only 8 to 10v). Is anyone already solved this problem?

turboB
25th October, 2015, 12:35 PM
hi friends need license.key
HW ID: lPUH+oVRBCW+apctGkDzjIOxTLs=
thanks

Yura123
25th October, 2015, 08:27 PM
hi friends need license.key
HW ID: lPUH+oVRBCW+apctGkDzjIOxTLs=
thanks

license.key

turboB
26th October, 2015, 01:02 PM
thanks my friend