help with this imobox

[dam495]

hi guys my custorm lost all his keys, the car is fiat palio 2004, and does not have a bc, just this immo box, how can i get a new key for this immo box,

i have mvp v9.99
sbb v 31.02
zed bull v 5.08
and upa prog,

it's possible right a key using zed bull?
or if not how can i pre coded a chip for ,program with mvp or zed bull are there solution for this tool, ? which o need ? chinese market has anything?

[super jumbe]

http://hobertech.com/uploads/images/car%20key%20programmer/Fiat%20Key%20Programmer.jpg

fiat key programming

If you have lost all the keys this tool will do the job???

1. Remove BSI PC from the car, the BSI PC is in the left side of the driver, with the insurance seat for one seat.Need to remove the whole insurance box, and take out the BSI PC from the back of the insurance box,then weld 93LC66, the following picture for refence.

2. After remove 93LC66?clear all the feet of 93LC66 insert 93LC66 to the adapter of this programmer as the following picture, then connect the adapter to the programmer.check below.

3. Switch on the LED turn red then trun green, which mean the programmer selt-test is normal.

4. Choose M1 or M2 to program keys.If the led light twinkle one time and the loudspeaker loud one tim, it shows that the programming is success.If LED lighting 5 times,and loudspeaker loud 5 times, it shows the wrong 93LC66 data or couldn?t find the 93LC66, need to check it is wrong with the connection or placement of the feet of 93LC66, and program keys again;If LED lighting 10 times, loudspeaker louding 10 times,it shows the ID48 chip is locked or the type of chip is wrong, need to program again.

5. Weld 93LC66 after finish the programming, and install BSI back to the car then it could be started.

:beer:

[dam495]

http://hobertech.com/uploads/images/car%20key%20programmer/Fiat%20Key%20Programmer.jpg

fiat key programming

If you have lost all the keys this tool will do the job???

1. Remove BSI PC from the car, the BSI PC is in the left side of the driver, with the insurance seat for one seat.Need to remove the whole insurance box, and take out the BSI PC from the back of the insurance box,then weld 93LC66, the following picture for refence.

2. After remove 93LC66?clear all the feet of 93LC66 insert 93LC66 to the adapter of this programmer as the following picture, then connect the adapter to the programmer.check below.

3. Switch on the LED turn red then trun green, which mean the programmer selt-test is normal.

4. Choose M1 or M2 to program keys.If the led light twinkle one time and the loudspeaker loud one tim, it shows that the programming is success.If LED lighting 5 times,and loudspeaker loud 5 times, it shows the wrong 93LC66 data or couldn?t find the 93LC66, need to check it is wrong with the connection or placement of the feet of 93LC66, and program keys again;If LED lighting 10 times, loudspeaker louding 10 times,it shows the ID48 chip is locked or the type of chip is wrong, need to program again.

5. Weld 93LC66 after finish the programming, and install BSI back to the car then it could be started.

:beer:
thanks but this car does not has a bc , just that immo box in the photo,to work with bc i have zed bull, but this is not bc , i've never saw that immo box before, any idea?

[darrenhyland]

can you open the immo box and post a picture of the inside....i think it might have 908 inside similar to 110.01.

[Badger-]

Same immo box as the Ducato an seicento i believe. Should have a 93lc56 eprom. Prepare id 48 key with zed bull module 12 and program to the car with mvp.

[darrenhyland]

Same immo box as the Ducato an seicento i believe. Should have a 93lc56 eprom. Prepare id 48 key with zed bull module 12 and program to the car with mvp.
module 12 is for delphi immobox....his box is MM

[Badger-]

module 12 is for delphi immobox....his box is MM

Sorry my bad should have looked closer :stupid:

[igorr]

orginal transponder temic 11
motorola SC512743CFU (1k59h)

[mastaflex]

tell us what do you have inside or post a picture, so we can help you better.

anyway i think zedbull will be enough for precoding and pin code, after program you key to car using mvp or SBB

[keygargoil]

if its after 1999 it will be id 48 module 62 with j66d mask

[dam495]

if its after 1999 it will be id 48 module 62 with j66d mask

it's code 2 with megamos crypto but the car does not have bc, just this immo box and one ecu, and module 62 of zed bull? tm pro? wich tool a need to do this job? and thanks

[keygargoil]

it's code 2 with megamos crypto but the car does not have bc, just this immo box and one ecu, and module 62 of zed bull? tm pro? wich tool a need to do this job? and thanks

so is your chip a motorola j66d il tell you what you need to do

[igorr]

immo 001for brasil
motorola SC512743CFU (1k59h)
Programaci?n de Controles (http://programacion.cerrajeriamg.com/)
lock in moduls section fiat