upa usb damage after install v1.2

[kasim_izmir]

Hi
Please can ypu help ? I am looking for solution for upausb 1.1
When i install upausb 1.2 , my upa damage . I write dump to 24c128
Give me message ;
upa usb connected ,programmer not found 1001

WBR
kasim

[technobox]

mate ur upa org or clone

[kasim_izmir]

mate ur upa org or clone
sorry mate , i bought from ebay :(

[einet]

100% clone!!!

[barbos]

How repair UPA after ver 1.2?

[jokersat]

programme ic 24c128 with this dump 100/100 can be work good again

@+

[marcus5]

Hello you can find out where the 24c128? thanks

[barbos]

programme ic 24c128 with this dump 100/100 can be work good again

@+

After rewrite atmel at24c128 UPA as unknow device too.
What me try

[einet]

You lost the RS232-USB converter firmware!

I tray this in one clone with change one from the orguinal.

[barbos]

[QUOTE=einet;1207961]You lost the RS232-USB converter firmware!

CY7C 68013 dont have internal ROM.
This chip based on core 8051
8051 in this chip can boot from RAM.
Firmware may written to RAM only from USB and i1c eeprom.
This chip dont have firmware.
I will try another dump.

[rabie_m]

post your dump upa

[jolidj]

hi friends, i bye the upa 1.1 , i upgrade this a 1.2 version and now dont work.
i write the 24c128(with file in this discussion) and now the pc see the upa programmer.
i try to read one eeprom 95640 but telle me only error.
help me please.thank you
i post my original upa dump after the upgrade.
the image is upa after write the 24c128.

[zeljolaki]

hi friends, i bye the upa 1.1 , i upgrade this a 1.2 version and now dont work.
i write the 24c128(with file in this discussion) and now the pc see the upa programmer.
i try to read one eeprom 95640 but telle me only error.
help me please.thank you
i post my original upa dump after the upgrade.
the image is upa after write the 24c128.

Try this..

[jolidj]

the usb driver is the same ??

[jolidj]

Try this..

thank you . work fine.

[LATTINO]

Hi all friend

My original UPA worked fine about two year.

Please can you help me, I am looking for solution for upausb 1.1
When start the programm give me message:
upa usb connected ,programmer not found 1001.

here is my dump

Best Regards

[ovi_dk]

Try to use the file from first page from this topic,write in 24c128 and try,if u have the same problem,loock to your driver,if its 3,4 reinstal and use driver from version 1,1
Good Luck!

[LATTINO]

Try to use the file from first page from this topic,write in 24c128 and try,if u have the same problem,loock to your driver,if its 3,4 reinstal and use driver from version 1,1
Good Luck!

I do it, is the same dump, cero diferences

[Tereksaz]

Hi all friend

My original UPA worked fine about two year.

Please can you help me, I am looking for solution for upausb 1.1
When start the programm give me message:
upa usb connected ,programmer not found 1001.

here is my dump

Best Regards
tell me your serial number UPA original 1.1?
I am try to help.

[didi_du_93000]

Hello,

I have UPA USB from china.
It's version 1.1.

I have tryed to use with vsoftware version 1.2 and now my programmer don't work.
I think when i have tryed the 1.2 soft my programer was automaticly updated and then locked.
I have tryed all dump from DK for 24LC128 but always same problem.
I have error " Programmer not Found 1001 "

Anyone can help me please?

[pepesound]

my UPA original work 6 yers perfekt

[didi_du_93000]

I have solved my problem with dump from this thread and with old driver.

[hugos31]

I have solved my problem with dump from this thread and with old driver.
upa clone, works well, you read memoirs? I recommend to buy?

[auto421]

hello friends, I have two upa usb and both are faulty. both when I connect the usb port are recognized by the program, but when I use the voltmeter current ranges until the 12volts and 16 volts. someone can help me with this fault? Thanks and Regards

[JammerOne]

hello there ,,

anyone can share the old Drivers and old Software after revive ,, I lost my CD ..

then I try to use 1.2 and it will damage again ..

thanks a lot ..

Regards,

[pezao]

180879
Upa 1.1

[JammerOne]

180879
Upa 1.1

Thank you very much about this ..

Appreciated

Regards,

[sanjaycip]

i have all version of hcip calculator
want to try one? lol :tee:

[JammerOne]

i have all version of hcip calculator
want to try one? lol :tee:
can you share?

[spider-wifi]

What is difference between original and clone?(beside update)

BR

[scarymistake]

Where can i find the 24c128 chip
Get this picture after update to 1.3
190868

190867


24c128

[Milkman]

IC4 on USB module =24c128.

[Kiselov]

programme ic 24c128 with this dump 100/100 can be work good again

@+
this file is a work?

[Dacha]

UPA USB V1.1 has stopped working.
not a changed version of the software
with the V1.1 software worked the next time a connection came up with a problem
upa usb connected ,programmer not found 1001.

V1.1 software and driver are reinstalled,
but unsuccessfulThe V1.1 software and the driver with which it worked has passed time but without success
reprogrammed 24h128 with landfills you set up here on the forum but without success.

replaced the USB cable and tried on another computer and again without success

UPA USB repair solution

In the event that the serial number of the interface is not evaluated in the software
and the error is "hop usb connected, programmer not found 1001" fixed
in the following way:


1. Check the safety of the 15V 160mA fuse on the main board. That was in my case was faulty.
After switching the fuse interface it worked.

2.If the disruption of the contents of the eeprom to the USB module occurs due to the change of the version of the software
it can be successfully reprogrammed.

Remove the USB module from the main board. Remove the USB module from the 24LC128 eeprom
and wipe it (FF FF) .Please empty the eeprom back to the USB module.

Connect the USB module itself without the main board to USB cables after which the computer will ask for driver installation.
Install the correct compatible driver.

After installing the driver, run the program according to which the program itself will be
offer entry of contents in eeprom. Allow to enter eeprom and do a reconnection
USB module on the computer after which the usb module will log

in correctly
on a computer that can be seen in the device manager.
In the softer it will still be a mistake for an unprocessed serial number.
uninstall the USB module and return to the main board.

Connect it back to the computer, start the software and in the status will
the serial number of the interface appears properly, indicating that the interface is working properly again.
The serial number of the interface is contained in some IC on the main board itself!

[montero2000]

hello friends i am in a big problem i will hurt my upa programmer usb clone and i need to program the 24c128 d that brings the interface thanks for the help

[montero2000]

I can not download this fail that I need

[Josep4891]

Is it possible to update the clone in version 1.2 to version 1.3?

[obd.tech]

Is it possible to update the clone in version 1.2 to version 1.3?

I would also like to know if this is possible ... please :hmmmm2: :)

[mustafr]

thank you for your help

[nelsonlince]

I have a clone UPA for some time it does not read the eprom. it does the reading process but it does not show the information. can you fix it with this file