PDA

View Full Version : Reanult with ECU Delco rare case!



dikseln
4th July, 2011, 01:41 AM
Hello,

I need to change the engine ecu of Renault Clio.

The ecu is:

HOM 7700861413
7700872546
BMUL

Delco
Made in UK


This ECU is old model 36pin and the mask of MCU internally of ECU is E22B

anybody know the way for revergin this ECU?
or immoOFF?

Thanks

atayok
4th July, 2011, 08:02 AM
virgin file

atayok
4th July, 2011, 08:04 AM
Empty the box private message

meli
14th July, 2011, 04:23 PM
@atayok can you give me pass for this file?

thanks in advance
greetz,
meli

haddia
27th September, 2011, 08:41 PM
Please pass thanks

mcsk8r
2nd November, 2011, 09:55 AM
please pass thx

tecautomotive
3rd January, 2012, 11:09 PM
what is password virgin E 9.rar (http://www.digital-kaos.co.uk/forums/attachments/f178/70071d1309762941-reanult-ecu-delco-rare-case-virgin-e-9.rar) thanks
my friend

tecautomotive
5th January, 2012, 06:46 PM
resolving thanks ecu is work

m3m5
22nd August, 2012, 06:17 PM
please atayok can you give me pass?

i need change this ecu from scrapyard.

This is immo off?

Meat-Head
23rd August, 2012, 07:40 PM
CHUFFING hell, yet ANOTHER GREAT tthread RUINED by people asking for a sodding password, why why why.

m3m5
28th August, 2012, 03:38 PM
I need this immo offff!!! or virgin!!! for this unit!!

PLEASE!!!!

atayok
31st August, 2012, 10:24 AM
hi no pass :)

m3m5
31st August, 2012, 01:43 PM
Thanks!!!
I have writted car start!! Light in dash blink but car start.

jolidj
31st August, 2012, 01:53 PM
what car mount this ecu??

Meat-Head
31st August, 2012, 02:10 PM
what car mount this ecu??

VERY VERY early clio.

Can i sell you one of these ECU's?

Got my DK subscription expired.


What chip is it?

jolidj
31st August, 2012, 02:26 PM
:) i see this ecu is from 1990......new generation

m3m5
31st August, 2012, 09:26 PM
Yes, old clio and 19 1.4 petrol

Key it's infrared, new ecu 700 eur too much for old cars.
Mcu it's Motorola mc68hc11e20 you can read with xprog chip it's secured but can be readed perfectly!

I removed light in dash! Hehehehehe

m3m5
16th September, 2012, 10:06 AM
Mates!! i have got problems with this ecu in the same car.

car fails, start but fails, run like 3 cilinders.

I have bought the same ecu from scrapyard. I have writte immo off in mcu. But car not start. plugs haven't got spark. car only crank.
Perhaps ecu from scrapyard it's broke? Any transistor open?

thanks!!

Meat-Head
16th September, 2012, 10:14 AM
cool is there a blob of sodder left inside ecu

m3m5
16th September, 2012, 10:23 AM
thanks meat!
Do you refer behind?? other face? cool weld point?

Meat-Head
16th September, 2012, 01:00 PM
thanks meat!
Do you refer behind?? other face? cool weld point?

i was thinking where you connected to immo off, if you have left some 'weld' in their.

m3m5
16th September, 2012, 07:25 PM
not mate !

this unit has got transparent rubber, you must remove this rubber for sold.

I can't find fault. Used ecu car only crank, ecu from car immo off car start but fails a lot. We have change coil, spark plugs, plug's wires, other distributor etc...

omglol
14th February, 2014, 10:32 PM
I also need to do this ECU. Does the virgin file work as immo off when immo wire is cut? Which pin is immo? Autodata shows 23, while some say 29?

omglol
15th February, 2014, 07:11 PM
Can somebody help me on this one? I used virgin dump from post #12, but car is badly overfueling ... injector is already open on ignition, so that's a bad solution. :(

Meat-Head
15th February, 2014, 07:15 PM
On iShit so can't view. Fill entire dump with ff. And hope

omglol
15th February, 2014, 07:49 PM
Whole dump FF for sure can't work ...

omglol
16th February, 2014, 11:42 PM
OK, after hours of research I finally found the solution. IMMO is in the last 2 bytes. I put C8 C8 (like in virgin dump), cut pin #23 (IMMO) and presto! - car starts.

Meat-Head
17th February, 2014, 08:29 AM
Cool can you upload photo of your prigrammer connections pleass

omglol
17th February, 2014, 08:23 PM
No, sorry, car is already away.

Piece of spacecake anyway ... 7 wires, solder to predefined soldering points, set frequency to 8000 kHz (a must! - Auto frequency won't work) and that's it. Talking for UPA, of course.

pollito128
26th January, 2015, 07:46 PM
hi omglol thanks for sharing your experience, you mean changing the last 2 bytesthe car starts.I'll try now hope to get lucky thank you very much