AM29BL802 pinout to Elnec Labprog

[paraver]

Hi,
I have Elnec Labprog 48 (ZIF 48) and i need to program one AM29BL802 but i don't have adapter.

Can somebody give me the schematics so i can connect it?

I only need to program one AM29BL802, i don't need to build adapter. Is it possible to connect just the necessary wires to Programmer?

Thanks in advance

[Zmann]

If you search the forum, I started exactly the same topic as yours 1 year and 25 days ago. Almost to get a solution but not!

I think that's not easy you make all wire connections, too complicated and too narrow pitch. Look at my that thread, I put an example diagram of an Elnec adaptor there. that's just for a 32 pin device and not 56 pins like this.

[paraver]

I've seen, but it was for beeprog, and the zif socket is only 40pin. That's why i created a new thread.

Maybe someone can help us...

250eur is a robbery for an adapter, to use one or two times.

[Zmann]

I think we both have ZIF48, is the wiring of adaptor #70-0099 you looking for?

[Room]

I think we both have ZIF48, is the wiring of adaptor #70-0099 you looking for?

Hi

I have DIL48/SSOP56 ZIF Flash-2 70-0099 Elnec adapter.
I need some time to check all wire connections to write schematics.
I hope two days will be enough.
Sorry, too much work just now.

[paraver]

Thanks a lot for your good intention of helping us.

I'm looking foward for your reply.

Thanks in advance

[Room]

DIL48/SSOP56 ZIF Flash-2 70-0099 pinout

[paraver]

Many, Many, Many Thanks!

R1, R2, R3 - The 3 resistors connect to pin 36 of dil48?

Best Regards,
P

[Room]

Many, Many, Many Thanks!

R1, R2, R3 - The 3 resistors connect to pin 36 of dil48?

Best Regards,
P

Yes. I think pin 36 of DIL48 must be Ucc

[garageozcar]

you can read with flash programmer this flash but file is crypted


best is use BDM
if no use BDM and use flash programmer you need use DECRYPTOR CRYTOR

here is

PLease Click to Thanks

[paraver]

I don't need to read it, i just need to write it.

It was a bad galletto write, but i have a dump that i'd already read it.

[Room]

I don't need to read it, i just need to write it.

It was a bad galletto write, but i have a dump that i'd already read it.

Some ECU has mixed data lines for the convenience of the trace.
Bosch and Siemens are different in trace.
You may need to convert dump before write flash with programmer.

[Zmann]

Thank you Room, what file extension is it.


DIL48/SSOP56 ZIF Flash-2 70-0099 pinout

[Room]

Thank you Room, what file extension is it.

It is simply TXT file.

[Zmann]

I think I have a problem with ZIP, just rename the unzip file with .txt but the file is not readable

Can you help to resend in .rar thanks

Ok now, no need a .rar uploading, I change the browser and it works.

[Room]

Can you help to resend in .rar thanks

Here is rar mate

[Zmann]

Your new post above is skipped over to the new page I didn't notice so I edited my last post, but thank you.

[Zmann]

Just finish all wirings, tested. Your connections are correct, thanks.


Here is rar mate

[paraver]

Just finish all wirings, tested. Your connections are correct, this's a helpful support to me, many thanks.

I may be able to accomplish one more small project, M58BW016DB, if similar wiring diagram of the Elnec adaptor #70-0225 can be found. I know it's time consuming work for the one who's going to tract out all 80 pin wiring.


Where did you get your SSOP adapter?

[Zmann]

China, one year ago and one time buying not certain for the name. But first time using was yesterday.

[paraver]

I've tryed to send dump (normal, descrambled or scrambled) and i allways get an error. Everytime on a different address.

I'm using an Elnec LabProg+

I managed to empty the flash, write 0102... etc, but when i try to send any of my dumps (original read with galletto or after egr removal)... allways error.

I cannot find original dump on the net.. MB C220 2.2CDI 0281011165

[leandroks]

I ve tryied to get the schematic but i couldnt find it could anyone get it to me???
AM29BL802 pinout to Elnec Labprog



Thanks a lot..

[dimitar]

Just finish all wirings, tested. Your connections are correct, thanks.
can you post the schematic mate??

[dunkler]

I need schematics for SSOP56 too, anyone can help?

[bidu20]

i need to read and write a AM29BL802 from Bosch EDC16U1 with elnec beeprog2c and adapter 70-0099. but when i write the file to a new flash i have no communication with vcds. anyone can help?

Thanks

[klom4548]

thanks thank you

[klom4548]

[报价=房间;1166261]DIL48/SSOP56 ZIF 闪存-2 70-0099 引脚排列[/报价]