PDA

View Full Version : IVECO DAILY 3.0 HPI FAP REMOVE



MACKIE
5th July, 2011, 04:04 PM
Friends I need help...need to remove FAP filter in:

Iveco Daily 3.0 HPI 16v 65c18 Year 2007

Inside EDC 16c39

EcuSafe 2.0 Not Working

1. After ecusafe : With diagnostics car shows NO FAP but still go in LIMP mode...shows error car oil fluid quality....and EDC lamp ON (Not Blink)

2. Before ecusafe :With diagnostics car shows FAP filter problem and EDC lamp blink...

Best regards and thanks

Mackie

MACKIE
7th July, 2011, 09:57 AM
Any solution for this?

Regards
Mackie

mikeli
9th July, 2011, 12:29 PM
Mackie,
you solved this?

I need help with this too...

Mikeli




Friends I need help...need to remove FAP filter in:

Iveco Daily 3.0 HPI 16v 65c18 Year 2007

Inside EDC 16c39

EcuSafe 2.0 Not Working

1. After ecusafe : With diagnostics car shows NO FAP but still go in LIMP mode...shows error car oil fluid quality....

2. Before ecusafe :With diagnostics car shows FAP filter problem...

Best regards and thanks

Mackie

MACKIE
9th July, 2011, 11:22 PM
No still have problem with limp mode...

Regards
Mackie

mariooo
10th July, 2011, 08:26 AM
No still have problem with limp mode...

Regards
Mackie

The file you read is not good
make a good read and post the file to the flash

MACKIE
10th July, 2011, 08:42 AM
File must be good with this file car start but FAP ON here is another readout...

Regards
Mackie

mariooo
10th July, 2011, 02:20 PM
File must be good with this file car start but FAP ON here is another readout...

Regards
Mackie
Your file is not good you have misread your ECU is a bosch?
if you open the file with these data ecm2001
Siemens 5WS SidXXX MPC563
Cod prod: S12453??????
OMO Cod: ?Z02810121931039
------------------------------
Cks: 2BEE
Size: 2097152 = 0x200000

Bosch? or Siemens? read the file with BDM

grinovsky
10th July, 2011, 02:44 PM
Your file is not good you have misread your ECU is a bosch?
if you open the file with these data ecm2001
Siemens 5WS SidXXX MPC563
Cod prod: S12453??????
OMO Cod: ?Z02810121931039
------------------------------
Cks: 2BEE
Size: 2097152 = 0x200000

Bosch? or Siemens? read the file with BDM
and from when the MPC563 use a dump of 2mo?

MACKIE
10th July, 2011, 07:44 PM
Your file is not good you have misread your ECU is a bosch?
if you open the file with these data ecm2001
Siemens 5WS SidXXX MPC563
Cod prod: S12453??????
OMO Cod: ?Z02810121931039
------------------------------
Cks: 2BEE
Size: 2097152 = 0x200000

Bosch? or Siemens? read the file with BDM

This is BOSCH and this is readout from BDM

ECU HW: 0281012193
ECU SW: 1037378086


Regards
Mackie

grinovsky
10th July, 2011, 08:59 PM
upload the dump dpf off that get you probleme with oil quality

MACKIE
10th July, 2011, 10:30 PM
Here it is...dump done with ECUSAFE 2.0 ...

With this file car starts and no FAP but still in limp mode and Oil problem..

Best regards
Mackie

grinovsky
10th July, 2011, 11:21 PM
ok, try this and repport for result
pw........pm

mariooo
11th July, 2011, 08:06 AM
ok, try this and repport for result
pw........pm
because you put all your passwords in a file?? If you want to help you use the password is stupid ... or aid or not by!

Hail .. I can not read the file properly in the original can not help you

mariooo
11th July, 2011, 08:17 AM
Here it is...dump done with ECUSAFE 2.0 ...

With this file car starts and no FAP but still in limp mode and Oil problem..

Best regards
Mackie
FAP off my file does not contain passwords I hope to be helpful for all my files I think works well hello

if you want to try it and write the result here

MACKIE
11th July, 2011, 11:21 AM
ok, try this and repport for result
pw........pm

With this file car wont start...

Regards
Mackie

MACKIE
11th July, 2011, 11:32 AM
FAP off my file does not contain passwords I hope to be helpful for all my files I think works well hello

if you want to try it and write the result here

With this file car start but still in LIMP mode and EDC lamp ON

Regards
Mackie

grinovsky
11th July, 2011, 11:36 AM
you have a probleme with your programmer
all the dump that you have upload here have wrong CKS since Flash Readout (http://www.digital-kaos.co.uk/forums/attachments/f173/70905d1310283699-iveco-daily-3-0-hpi-fap-remove-flash-readout.rar) file that is original but have wrong cks

MACKIE
11th July, 2011, 11:46 AM
I know that CKS are wrong but programmer fix it when writing....BDM read flash without CKS, ECU SAFE also wont correct checksum....so i need file with FAP OFF without correct CKS...my programmer will fix CKS...no worry...

Regards
Mackie

grinovsky
11th July, 2011, 11:52 AM
yes,but i sent you file with FAP OFF and correct cks and when you write it your programmar change the cks to wrong
that's why the car don't start

MACKIE
11th July, 2011, 11:53 AM
Thats right my friend ;)

Regards
Mackie

mariooo
11th July, 2011, 01:07 PM
Thats right my friend ;)

Regards
Mackie
I do not think you read that right file fromto 29bl

have you tried the file I sent you on page one?

mariooo
11th July, 2011, 01:11 PM
Thats right my friend ;)

Regards
Mackie
instead of using BDM tries to read obd d apres EDC16C39 and e-file you'll see that reading is better than your BDM does not work

MACKIE
11th July, 2011, 01:19 PM
I do not think you read that right file fromto 29bl

have you tried the file I sent you on page one?

Yes I tryed that file and I post result file start the car ...no FAP but still in LIMP mode...

Regards
Mackie

MACKIE
11th July, 2011, 01:20 PM
instead of using BDM tries to read obd d apres EDC16C39 and e-file you'll see that reading is better than your BDM does not work

And believe me my BDM is ok

Regards
Mackie

MACKIE
11th July, 2011, 01:35 PM
Here you are Galletto readout too...

Regards
Mackie

mariooo
11th July, 2011, 02:21 PM
Here you are Galletto readout too...

Regards
Mackie
The file that you read all right now, these data are accurate ..
Bosch
EDC16C39
1037378086

write the file using obd cock

you'll see that it works

after you unplug the sensor, which is close to the discharge from the two tubes and leaves the sensor free fap

grinovsky
11th July, 2011, 04:54 PM
And believe me my BDM is ok

Regards
Mackie
IF your BDM is Ok he shuld read the dump from ecu with right cks like is donne with galetto
may be you use a different plugin to your ecu to read/write with BDM!!!!!?
try this ,it's the same lake the other but from galetto dump
same pw

MACKIE
11th July, 2011, 06:28 PM
The file that you read all right now, these data are accurate ..
Bosch
EDC16C39
1037378086

write the file using obd cock

you'll see that it works

after you unplug the sensor, which is close to the discharge from the two tubes and leaves the sensor free fap

With this dump EDC lamp not blinking just light ON and car start but still in LIMP mode....

I unpluged 3 connectors two from FAP tube and one below bonet...

Regards
Mackie

MACKIE
11th July, 2011, 06:29 PM
IF your BDM is Ok he shuld read the dump from ecu with right cks like is donne with galetto
may be you use a different plugin to your ecu to read/write with BDM!!!!!?
try this ,it's the same lake the other but from galetto dump
same pw

With this dump same problem EDC lamp not blinking just light ON and car start but still in LIMP mode....not more then 3500RPM...

Regards
Mackie

grinovsky
11th July, 2011, 06:43 PM
what's dtc?
is the probleme relative to oil quality gone?

mariooo
11th July, 2011, 07:17 PM
With this dump same problem EDC lamp not blinking just light ON and car start but still in LIMP mode....not more then 3500RPM...

Regards
Mackie
I think your BDM has read and written so bad you ruined your files delal ECU .. try to find a backup of this unit and write it all again, maybe you've ruined the file E2PROM .. I did my other files works dayli

grinovsky
DK Veteran
I do not understand why you put the password to your files I give everyone the chance to see what kind of help from the forum? You will not help anyone to understand that your files are always good ...

mariooo
11th July, 2011, 07:18 PM
With this file car start but still in LIMP mode and EDC lamp ON

Regards
Mackie
maybe you should clone your ECU with no equals fap

MACKIE
11th July, 2011, 08:08 PM
OK....last results from testing...

Oil DTC gone...EDC lamp was ON because of OIL DTC now when DTC is cleared no more EDC LAMP....

With all FAP OFF DUMPS car start and have no DTC no EDC LAMP...but LIMP still there....

Car can't run more then 3500RPM's...in first start car can go over 3500RMP's but after couple seconds go in LIMP...

I unpluged 3 connectors two from FAP tube and one below bonet...

Don't know why maybe our dumps are not good...

Regards and thanks for help
Mackie

MACKIE
11th July, 2011, 08:14 PM
I think your BDM has read and written so bad you ruined your files delal ECU .. try to find a backup of this unit and write it all again, maybe you've ruined the file E2PROM .. I did my other files works dayli

grinovsky
DK Veteran
I do not understand why you put the password to your files I give everyone the chance to see what kind of help from the forum? You will not help anyone to understand that your files are always good ...

Read this post before....My files are 100% good (READ ALL FILES WITH BDM, GALLETO AND ELNEC BEEPROG+) this car before we start all procedure had same simptomps cant run after 3500rpm's i think it is because some kind of LIMP mode....

But that LIMP mode was maybe because of FAP errors...now when we clear all that errors still same problem....

No LAMPS no DTC's but car want run good....

Regards and thanks
Mackie

mariooo
12th July, 2011, 09:47 AM
Read this post before....My files are 100% good (READ ALL FILES WITH BDM, GALLETO AND ELNEC BEEPROG+) this car before we start all procedure had same simptomps cant run after 3500rpm's i think it is because some kind of LIMP mode....

But that LIMP mode was maybe because of FAP errors...now when we clear all that errors still same problem....

No LAMPS no DTC's but car want run good....

Regards and thanks
Mackie
I'd do a test at this point .. try to find the original file on the network if there is no version of FAP and write it instead of your original ... it seems strange that turns off the light with the file fap off! Usually with both ecusafe vers.1.9 2.0 EDC16C39 that work well ...

trying to find an original file without fap .. I found this site

Iveco is not easy to find a file on the network ..

0281012193_378086_ORIG (http://www.tuningserver.com/index.php?page=shop.product_details&product_id=162&flypage=flypage_images.tpl&pop=0&option=com_virtuemart&Itemid=2&lang=en&vmcchk=1)

MACKIE
12th July, 2011, 10:15 AM
I think that those files are good and that otiginal files maybe not solve this problem....

Regards
Mackie

grinovsky
12th July, 2011, 08:42 PM
try this and report
same pw
dump from galetto

tachonow
12th July, 2011, 09:41 PM
Do you have diagnostic tool for reading the values ?

grinovsky
12th July, 2011, 09:48 PM
i have more than diagnostic tool,i have the dump
probleme solved for MACKIE (http://www.digital-kaos.co.uk/forums/members/231188-mackie/)

MACKIE
13th July, 2011, 12:43 AM
try this and report
same pw
dump from galetto

I'll try this first thing in the morning and post results...

Regards
Mackie

grinovsky
13th July, 2011, 01:41 PM
repport please,the night is soon

soundnavigator
13th July, 2011, 01:52 PM
I think that you need to try with all sensors plugged on. For EDC16C9 and C39 sensors need to be included.

Best regards.

MACKIE
13th July, 2011, 02:31 PM
I think that you need to try with all sensors plugged on. For EDC16C9 and C39 sensors need to be included.

Best regards.

Are you sure about that ?


Regards
Mackie

MACKIE
13th July, 2011, 02:32 PM
repport please,the night is soon

Problem solved car is not in LIMP mode anymore...no more EDC LAMP...

Best Regards and thanks
Mackie

svrecar
11th June, 2012, 05:40 PM
Hi,

Can anybody enlighten me, how to deactivate limp mode?
Iveco 60c18 ....same soft as above.
Should sensors stay connected or not ?



Br,

svrecar
11th June, 2012, 07:45 PM
O.K.

I tried to made dpf off manually, got past dpf errors, so now i have no dpf no mil and limp mode (3500rpm) car.
I tried to make it with swiftec , but with no luck...still limp mode (sw&hw numbers are the same,but soft is different (versions 086,086a,086b,086c,086d....) basically maps are slightly different and not all are in all versions)

I checked the wiring ecu---sensors, all ok.
I am shure that i need sensors disconnected. :dong:

Any help would be very much appreciated. :giveup:
Br,

tarekdj
14th June, 2012, 09:23 PM
Hi,

i have Peugeot 406 2.2hdi Fap year 2001, Bosch EDC15.
Now my problem with DPF, I can not communicat with ADGGO1 calculator, I am sure that my eolyse is low (just 160g).
With Multidiag when i diagnos engine he tell me that the eolys is low and the sensor of eolys is not good.
Now i am not in limp mode , juste the indication that '' Amonalie Additif Gasoil''.

- Can you tell me please, if this indication ''Amonalie Additif Gasoil'' desapear whene i make DPF-OFF with swiftec.
- Can you tell if the difference of Swiftec and Ecusafe was juste to no-need to change any think in BSI.

Thank you for all your supports

mifko
14th June, 2012, 11:49 PM
Friends, if anyone has a solution to exclude FAP. Everything I tried failed. Ceksuma be good, but when I type the car will not start. Thanks in advance for help

PanN
27th September, 2012, 03:56 PM
hi. i have same car with same problem.
try ecusafe and volta.
NO FAP but still go in LIMP mode...shows error car EDC lamp ON.
can help me with solution ?

dakoal
1st October, 2012, 11:52 PM
Hi,

because of same Problem, is there solution?

best regards

rottweiler71
19th June, 2013, 02:15 PM
Hi. I have same problem with Iveco Daily 3 HPI 0 281 012 193, i understand resolved problem with DPF OFF2.rar ?! Send me please pasword from this dump.
Thank You very much !

Africa
17th July, 2013, 11:23 PM
seems that many of you feel the same.
If not start, you may BDM calculate your chk automatic, but the old version of the checksum is the ecu. The most modern ecu takes more changes better than the old computers do not recognize. for that may be that if the chk is ok, and the write change, and not be chk ok. : Arriba:

Africa
17th July, 2013, 11:48 PM
I have one the same, and made with ecusafe and perfect, whith BDM-EVC , no faults marked, but the two weeks the car comes with lack of power and does not exceed 3500 rpm and will charge any forward again but customer at 2 weeks back with the same problem and mark on the diagnosis Fap 67% of soot.

Help me!!!

Africa
27th July, 2013, 12:40 AM
I have the same problem. is no more than 3500rpm. You've solved? ..
send me pass please!!!

Africa
28th July, 2013, 12:02 PM
pass please!!!

ecutuners
28th July, 2013, 02:44 PM
All iveco dpf off no problem, only manual solution works 100% i did many times, no limp mode, no loss of power, no problem

ominimicu
28th July, 2013, 10:27 PM
Do with volta and raise torque and limp mode torque to max

sarkann
2nd September, 2013, 02:55 PM
Hi guys, don?t be so grasping to earn everytime. Good tuner has a lot of better oportunities for making money.

Here you are - DPF OFF file for everyone. Tested. TQ limiters for limp mode extended, DTCs erased, postinjection done by ecusafe. Enjoy!

greyg
4th September, 2013, 04:18 PM
sarkann,
Your solution works only on 65C18 ... and has a lot of errors. EGR damage after some time.

clio_williams
3rd November, 2013, 08:22 PM
Regularly i make dpf off for these , neither ecusafe nor others can solve it as this ecu and engine is differently configurated in terms of ecu. U have to do it manually one by one finding the all necessary maps...

tonih
4th November, 2013, 10:27 AM
Only solution manual for this ecu

angelx431
20th November, 2013, 05:46 PM
Help PASS! for DPF OFF2. THANKS!

alfista51
12th December, 2013, 11:29 AM
Hi friend
i have need dpf off on this IVECO DAILY 3.O234617234618

vlade
18th January, 2014, 06:13 PM
please can you send me a paswpord for the file dpf off2.rar

zeljko84
28th January, 2014, 06:26 PM
Hi friend

I have problem too

Iveco Daily 3.0 hpi
Bosch edc16c39
1037378086

try with ecusafe, volta ... not working stay on limp mode

Download file iveco_dialy_3.0_hpi.rar (http://rg.to/file/97822e4256815ad73ebf78cecea0af1b/iveco_dialy_3.0_hpi.rar.html)
(ori&try files)

Any help?

metercar
17th October, 2014, 05:51 PM
Hi
I need correct the cheksum of my Iveco

3.0 HPi

Thanks! :top:

mario38
17th October, 2014, 06:37 PM
Hi
I need correct the cheksum of my Iveco

3.0 HPi

Thanks! :top:

iveco cks ok

avskpu
27th May, 2015, 08:53 PM
Help pass for DPF OFF2.
Thanks!

brombal
9th October, 2015, 01:34 PM
Help PASS! for DPF OFF2. THANKS!

neokreska20
25th January, 2019, 04:56 PM
pass pleas DPF OFF2 THANKS