View Full Version : Chrysler Crossfire 3.2 - Virgin dump needed - 0261 208 425 - ME2.8
Pali33
9th August, 2011, 03:08 PM
Hi all,
i have problem with this car:
Chrysler Crossfire 3.2 160kW
0261 208 425
ME2.8
Motor don't start and in ECU is this fault code:
P2071 - START ENABLE OF DAS NOT SENT CHECK FAULT MESSANGES IN CONTROL MODULE EZS (P1999)
I have just ECU (0261208425) and Immobox from this car. Dumps from ECU (95p08 + 29f400) are attached.
In immobox Siemens (5WK4 8697, 170 820 17 26) is processor:
Freescale (Motorola) QFP64
SC507540CFU
1D69J
Please, can anybody help with this problem. If needed, i can read (with UPA) Motorola processor in Immobox, but i don't know which procesor is this. Is this MC68HC08?
Many thanks in advance!
Pali
Pali33
10th August, 2011, 07:59 AM
i found eeprom 93c56 in Immobox. Maybe can anybody repair or virginize this dump:
dilick
10th August, 2011, 08:12 AM
what about fault codes on IMMO box?
does it recognizing key ?
what says live data
nothing
10th August, 2011, 06:29 PM
sound that you need to process the fault in immo box , try to read the actula values in Immo box when you install the key in the switch see if the immo box can recognize the key , ME 2.8 virgin in eeprom not in the flash , but the flash back and eeprom and proceed in immo box , we can make keys for the immo box in case the immo box can't recognize the key , or change the immo box and we can virgin the ecu for you :) good luck
nothing
10th August, 2011, 06:32 PM
can you take a picture for the immo box ? 93c56 in immo box ? as i know all the data in 705x32 ( 64QFP )
Pali33
11th August, 2011, 06:25 AM
here the picture and dump from Motorola 68hc05x32 (QFP64).
Unfortunately, i don't know, if the immo box can recognize the key. I have only the ECU and Immoobx. The car is 300km away from me and i have very few information. I suppose, the car owner has change the BATT and after that motor don't start.
Now ist the situation as follow: engine starter rotate, motor startet and go out immediatelly (after 1 second). This happen 2 times. Then engine starter not rotate.
It must be disconnect the BATT, then motor started again 2 times (but only for 1 second).
I think, the synchronisation is wrong.
Please, can anybody do "something" and i send it to car owner to test.
Thanks.
Pali33
12th August, 2011, 08:39 AM
... i suppose, the immobox can recognize the keys. What to do next? Make ECU virgin?
Pali33
18th August, 2011, 07:10 AM
Nobody can make virgin for this ECU (ME2.8, eeprom 95p08)?
Many thanks in advance.
sogaro
18th August, 2011, 07:57 AM
Factory data: 3A80827AA508162B18462B4A5F7F1220303030303030303030 30303030303030
Pali33
18th August, 2011, 08:22 AM
Factory data: 3A80827AA508162B18462B4A5F7F1220303030303030303030 30303030303030
thanks mate,
what means "factory data"? What's the use of it?
addgsm
4th May, 2012, 11:26 AM
what software u use to make ecu adaptation? i have try with mb das but cant get communication
br
chiptorque
29th July, 2014, 08:55 AM
hello mate, sorry if I upset you this query: I have a similar problem with the same vehicle Chrysler Crossfie, same ECU and same Inmobox.
as I solve the problem? Ecu Virgin? Virgin Inmobox???
I need to fix this as it is a colleague and we have sold.
thanks and regards.
duplikeytor
22nd October, 2016, 05:15 AM
Any solution to this if ECU and IMMO in hand? To make new keys and SYNC?
duplikeytor
5th March, 2017, 02:59 AM
Any info pleasE?!!!
Addautokumasi
28th February, 2020, 10:55 AM
keep up the good work
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.