BMW 320 Bosch 0 281 001 445

[t77]

Hi friends I need help with immo off BMW 320 ECU Bosh 0 281 001 445 ,I was tryed with otocheck2 car still not start (EWS relay short) ,maybe who has experience with this model and could help me .In side 2 flash 29F010 and EEPROM 24c04

[immokill]

Hello

Here you go . Try it..
Need to prog all files. It is 24c02 small eep and 2 flash memoryz.

Report please!



Regards

[t77]

Hi Immokill thanks for quick answer...ok I was trayed your files and car not start ,only crank .Write 2 flashes High and Low a nd eeprom and nothing.

[immokill]

Hello


Did you disconnect ews?
I personally didn't try it but it is working solution as I know.


Regards

[immokill]

Hi

Here are more files.




Regards

[immokill]

Hello

Any news ?
Did you start that bmw?


Regards

[graczek234]

hello @immokill , i can see you really want to help people so i hope you can help me :D
my problem look like this:

car have working ews with good key, someone put there second engine with second fuel pump, car is cranking but won't start, when you spray cockpit spray it runs
i have two ecu's :
one from the car valid vin, ews and others- EDC15M 0281010205 7786887
second ecu from donor of engine - 0281001445 2249970
the question is what can i do to make this car running? i have kess but i think it can't do the job, also have ktag,inpa cable
i am big newbie still learning but i'v done one immo off and some popmods ms41/42
with the devices i have can i read both memory and eeprom or i have to desolder eeprom and buy programmer?
i am wondering if virginize edc 0281010205 will do the job or better do the ews sync to the 0281001445?
BIG regards for any help

[graczek234]

sorry for lack of informations, car is of course bmw 320d 136 hp
ecu 0281010205 -2001yr
ecu 0281001445 1999yr

[Lambda1]

There isnt any released solution, as far I know about EDC15M immo off... the carlabstuff dont work.

[graczek234]

i know EDC15M can be virginized, but not immo off. i am wondering if that can do the job, car have working immo but engine with fuel pump from other car.
i've readen there is immo or sth in pump and that is why car won't start
also i've found that ecu 0281001445 can be done immooff info from ECUbyte- YT and mhhauto. but there is only info that can be done without any solution

second question is what device or program i need to read that ecu, K-tag don't have protocol, kess can only read flash
i've done ms41 on the bench by inpa cable but there were program for reading/flashing ms41

[graczek234]

immo universal decoding can do the virgin, but i need eeprom 24c04 i think flash from kess wouldn't be enough .
so question, what programmer would you reccomend?
tell me if i'm thinking right or i am far away from solution? :highly_amused:

[graczek234]

There isnt any released solution, as far I know about EDC15M immo off... the carlabstuff dont work.
Okay, so far i tried to read the eeprom from both ecus
Ecu from car eeprom 24c04 readen with no problemEcu from donor 24c02-can't read-only FF, probably bad memory
What can i do in that case? And question is why car won't start but cranking, i have readen there is NO IMMO in pump so where is the problem?