volvo with audi motor immo off

[zoro1]

Hi i need to know how to remuve immo for this car,Bosch ecu N 0281001592
And where immo chip is?there is some atmel chip on the component side,but it is not 2402 or else .
Thanks for your answers.
EDC MSA 15.7-4.2 and clear dump please

[zoro1]

i am still need this file please

[damih]

Hello,post picture of ecu

[zoro1]

hI ,I will take a photo soon as posible,becose the car is no here...

[delio78]

only emulator of k-line from white immo box

best regards

[zoro1]

the new ECU is from crased car and it is with immo box and key,but the car starts only for 2-3 sec and turn off.Pic of the ECU and dump from file soon as I reurn from holyday.

[zoro1]

Here are pictures and dump from eeprom ,but may be it is wrong dump.My pc crashed and tomarow i wil restore HDD from it and i will post dump read with UPA,this dump I read with JDM and IC prog.

[zoro1]

And more pictures.The chip is ATML81402-b1,but in UPA is 24c02

[klakier]

a few day ago i done very similar ecu from audi read memory 24co4 or 24c02 and post here.

[zoro1]

Is my dump correct or not?Here are pictures from volvo scaner screen

[klakier]

your dump is good but, I can`t do immo off you must buy immo emulator.

[zoro1]

I think my dump is not correct,Datamaneger sey:wrong dump file,Why do I need to by a emulator ,the car is with original immo box end ECU and key,there is change from petrol motor to disel motor -but the change is complete-all electrical installation with sensors and zll crap is moved.
Now here is dump read with BP Programmer ,i think it is correct,but i stil can not find original file,this one is "cleaned" with dataexplorer maneger.
PS.file VOLVO is H and L from 29f010 in the ECU

[zoro1]

Are you shure that i need emulator for this ECU?Where can I be wrong?The immo box and key and ECU is from old car and still can start engine...Turns on for 2 sec and go off .

[zoro1]

Well is there a solution for this ECU or not?

[zoro1]

Is posible that immo to be in imo box?There are eeprom and some MCU?

[gtmech]

Is my dump correct or not?Here are pictures from volvo scaner screen

what volvo software is that your using buddy?

[bgcomp80]

Volvo FCR is the software .

The problem is that the IMMO BOX is different for diesel engine, you need the original IMMO BOX to be paired with the ECM .

[zoro1]

Yes Volvo FCR with vag com USB interface,but in DM is at com port 1!I hawe a ori immo box,but there is a eeprom ,and some gays tampered with it.Where I can find a original dump,or all dumps are different?

[zoro1]

Today I'v try files from data explorer manager,ECU Vonix,cartool,different immo cleaners-car starts for 2 sec and go off.Did enybody knows wich audi car hawe this motor ,and is enyvere files /HI and LO /for it.I will try to write files and start the car like audi,there is MSA,but the file is not good for me,in original Volvo style.
PS.With 24c02 remuved car is starting for 2 sec and go off,with original dump with or without immo box car wont start.

[chriskross]

it is audi A6 4A 5 cyl diesel 140 ps AEL 2,5l tdi

[ohhello]

Why not use a US spec file? We didn't get Immo systems here till 1999. So all 1998 and earlier bins are no immo. So long as the pinout is the same on the ECU it would work. PM me and I'll send you a known good M4.4 bin file that will remove immo and you can then tune.

Over here all our ECU's are 0 261 204 xxx so you might need an actual ECU from a US spec car. I have plenty if you need one. Pay shipping and I'll send it to you pretuned....

[zoro1]

still need solution!here is dump from immo box
....

[zoro1]

Well there is no solution i think,so from where to find immo emulator for this car?To bay or make it?

[zoro1]

PROBLEM SOLVED.CAR IS RUNNING!

[ecarruda]

What you did?