Clio2 PIN from UCH dump

[niki85]

Hello

Please could someone calculate pin code
from UCH p8200065817--a 93c66
clio2 1.2 16v year2002.



Thanks

Regards

[ammarben]

corrupted fife read again

[boukad]

hi
dump incorect

[florin_leo]

The pin code is 000000468800

[niki85]

florin leo
sorry, pin is wrong

hope this is good dump

[niki85]

without arhive can`t upload

[florin_leo]

Is the same dump like first.

[alfabit]

florin leo
sorry, pin is wrong

hope this is good dump

Wrong dump, it says your VIN is : 0123456789ABCDEF !

[niki85]

hi

from last clio2 i ask for pin code and file was very similar,
uch was been 8200 234 045 UCH-N2, eeprom same 93c66.
i got pin 3FFCDCFAF2CA and it`s work`d

i don`t think that i have done bad reading 93c66 ( with beeprog ),
i know your type of calculation florin leo
first 2 number from 126H, second from 189H, third from 1A6H, fourtd 125H, fivetd 1A5H and sixtd 188H, but that work for
another type of UCH, and in that type you can see VIN number
if do swap bytes.

if someone know the solution, i would like to know.
thanks

regards

[niki85]

i forgot to tell that when i look in status and parametars
of UCH with Clip, i found empty configuration, car won`t turn over, no fault in uch, no fault in engine and immobiliser is ok too, i succesiful do configuration and all i need is to programm the keys.

all simptoms starts when battery went out...

sorry for bad english ( if it`s bad :) )

[damih]

Hello,I think your read is good

but he have lost some info (like code PIN ect)
it's like virgin sometimes you can get 0123456789ABCDEF and no VIN because renault factory don't program it

you can post dump of ecu to get a rigth PIN and try to configure this
or find a good dump of uch for your cars
reset ecu then programme a new key

[niki85]

hi damih

how to read ecu, i think it`s magneti marreli half hibrid

regards

[niki85]

now i see it`s IAW5NR.C2

[richard27]

Pin Kod: 3FFCDCFAF2CA

[niki85]

yes that`s pin code for uch that i post for exaple, also i post the pin code too ( you can see it ), but i need pin code for dump from first post, or 5th post ( it`s same dumps ) .

thanks

[niki85]

any luck ?

[niki85]

i can`t read hybrid ecu 95160 to make virgin
and somehow make virgin uch but again i don`t now pin code...

[damih]

Hello,have a look here

http://www.digital-kaos.co.uk/forums/f178/renault-clio-5nr-ce1-immo-off-221489/#post1214958

[niki85]

yes i try to read but without sucess, tonight i try more, connect that 4 wire, external connect +5v and gnd to programmator, and disable pin check, he read but nothing in a buffer.

[PierreTheron]

Wrong dump, it says your VIN is : 0123456789ABCDEF !
Hi Alfabit . I have found many dumps on clio2 without vin that looks similar to this .
If you connect clip it stills finds vin number from other unit. sometimes you must input the vin if it does not find it from uch or airbags module.But with or without vin car is still a runner.

Niki .. Your file for uch n2,n3,bg???
It seems there are no keys written into this file so i presume there will be no pin code for this file..

Keys in line 50 and line 60.



What model year is this vehicle??
.(You seem to get different algo on these>>

[niki85]

Hi
it`s year 2002.,
in immo parametars 0 key programmed, car won`t crank, no immo light on dash.

i think that uch is BG because n2 or n2 not writen on label.

[niki85]

does someone have virgin UCH dump or know how to make?

[alfabit]

does someone have virgin UCH dump or know how to make?

Save the actual dump and write all the prom with FF all locations. ( erase it completely ) Some UCH work this way, make virgin. If do not, you can go back whenever you want, rewrite the prom with the dump you previously saved.

[niki85]

thanks i`ll try now.
i got pin code from diler throw vin, but when try to program keys, say that uch is empty, when try to programm uch say that pin code is wrong...
i will kill my self....

[niki85]

with all FF not work for me, same as before,
maybe i get wrog code or something...

[PierreTheron]

Hi

Virgin file for uch.

Pass in pm

[richard27]

Hello

Please could someone calculate pin code
from UCH p8200065817--a 93c66
clio2 1.2 16v year2002.



Thanks

Regards

24D70DAD5799 This must be your pin code

[niki85]

now i go try,
will post results

thanks

[niki85]

richrad27

pin code is ok, but
when i try to programm keys say that UCH is blank,
when i try to program body, pin code is ok but say that pin is not corespond to the key.
i try my original dump, virgin dump and few dumps more but always the same.
what now?

thanks

[alfabit]

niki, go to the reprogram UCH procedure, if empty you need to input only APV code, and old keys must be recognised. No old keys, you must reprogram new ones, it should work this way.
Old keys are linked to the APV of the car, they will work with the UCH reprogrammed with the old APV that you now know.

[niki85]

alfabit

i don`t know what is APV code, how i can know what is my apv code ?? where to get it ?
in Clip i see option SPARE and there want to enter some code
is that apv ?
i have two old keys

thank

[alfabit]

alfabit

i don`t know what is APV code, how i can know what is my apv code ?? where to get it ?
in Clip i see option SPARE and there want to enter some code
is that apv ?
i have two old keys

thank

APV = apres vente code, also known as PIN code.
I use ddt2000, it is very simple to reprogram keys and UCH, i don`t know what code asks clip for.
The old keys you must know their APV, write that APV inside a virgin UCH and they will work . The APV you were told by the dump you posted here. It must match the keys APV.

[niki85]

hi again

now after many spent hours get immo light fast blinking ( been off all the time )
but i don`t have damn pin code again
if someone have strenght to help...

[topclef]

hi again

now after many spent hours get immo light fast blinking ( been off all the time )
but i don`t have damn pin code again
if someone have strenght to help...
:wink:
PIN CODE = 45 57 5D FE DC B2

[Johnner]

I get the same pin as Pierre


Regards,

[Johnner]

I get the same pin as Pierre


Regards,



Doh!! That was meant to be Topclef !! Sorry !!

[niki85]

still got no start the clio

[gabigafu]

Pin code : 8B9FCD9ACD6F

[niki85]

gabigafu

from which dump is that pin?

thanks

[gabigafu]

from uch10.rar

[PierreTheron]

Hi

At the moment this is all i know about these dumps.

Maybe it can help ..

[niki85]

gabigafu
that`s wrong pin, topcelf give`s right pin in upper post.

pierre very nice, i`ll try to play, but i don`t know in which line
is pin and sinhro with ecu

thanks

[niki85]

hi

can i fit and make virgin iaw5nr2.c6 instead my iaw5nr.c2(hybrid) ??

thanks

regards