need immo of 4mv.f

[jolidj]

need immo of for this ecu , the car is polo.
please help me.

[haroutioun]

need immo of for this ecu , the car is polo.
please help me.
----------------------------------------
Hi,
friend till know no immo off yet>>>for M/M ECU
maybe pin code can help you>>> (00108)

[jolidj]

for use the pin code must have the VCDS??vas 5054 is the same??
i enrty in the imobilizer voice and tell immo of??
is wright??

[tecautomotive]

eprom 87c510 or 27C512 ?
post file

[jolidj]

the ecu are flash 29f400 and eeprom 95080.

[haroutioun]

for use the pin code must have the VCDS??vas 5054 is the same??
i enrty in the imobilizer voice and tell immo of??
is wright??
-----------------------------------------------
Hi,
friend what is your problem in the car? way you want to do immo off ?
about enter the pin yes you can use (VCDS) & by vas (5054) must calculate 4 digit pin to 7 digit when you want i am ready to do this for you, after you can to enter the pin on login,
& about immo off MAGNETI MARELLI 1AV-it must be (27c512) but try....

[jolidj]

i have the problem whith original ecu,wen i read the eeprom i erease it :( :(.
i find anather ecu, and to enter this new ecu in the car i serch the immo of.the car dont start.the ecu is 4MV.F dont have the 27c512.help please

[haroutioun]

i have the problem whith original ecu,wen i read the eeprom i erease it :( :(.
i find anather ecu, and to enter this new ecu in the car i serch the immo of.the car dont start.the ecu is 4MV.F dont have the 27c512.help please
----------------------------------------------
ok, friend did you have tool can read your pin from dash?

[jolidj]

i have texa axone tool.
if i entry in dash section ,i find the pin dash???

[haroutioun]

i have texa axone tool.
if i entry in dash section ,i find the pin dash???
--------------------------------------------
friend is this tool can read by OBDII or by dump? i dont listen about this be4 ,sure in DK friends know about your tool,
so try read carefully if it is by dump,if by OBDII it is simple .
ok?

[jolidj]

ok, i read the dash eeprom??
and more ??

[kokkinos panos]

then u adapt new<used>ecu and job done if everything else in the car is ok!

go ecu engine

block 50

enter pin that DK found for you and then go again engine ecu=
block 50 and change pin with the pin that you found in your dash


or visit rosstech wiki page and you will find everything you need
to do this job.

[haroutioun]

ok, i read the dash eeprom??
and more ??
-----------------------------------------
1) did you calculated your dump, to get pin which read it from dash?
2) or by OBDII you get your pin code?
3) if you get your pin from dash>> use manual of that DK found for you..

[jolidj]

ok i understand, the pin dash is number ,i found this in to dash sector.(ore i read the eeprom in the dash?).esist a screanscot to see this operation?
is the first time for me.

[haroutioun]

ok i understand, the pin dash is number ,i found this in to dash sector.(ore i read the eeprom in the dash?).esist a screanscot to see this operation?
is the first time for me.
---------------------------------------
my friend,
1) in the dash you must have eeprom i thing (93c86) get this eeprom & try to read after post it hear in DK, the same lick which you load it above (ecu dump),after we give you the pin code of the dash,ok?
when you get the pin of dash + ecu (oraddy you have it) after you can adapt and your problem it be solved ok?
if you have to ask any question feel free plz.

[jolidj]

i dont have vcds to read the eeprom dash.i have only texa tool and this texa i dont read the eeprom dash.
texa take me this data dash area.ecu code.q0920820
kombi ecu wegfahrsp VDO V08
codification 1141
thanks for all.

[haroutioun]

i dont have vcds to read the eeprom dash.i have only texa tool and this texa i dont read the eeprom dash.
texa take me this data dash area.ecu code.q0920820
kombi ecu wegfahrsp VDO V08
codification 1141
thanks for all.
--------------------------------------
friend,
1) vcds cannot read eeprom from dash,only for diagnostic + you can adaptation your key + ecu +++.
2) let me know how you read eeprom 95080 from ecu + flash dumps?
the same, you can read from dash, open the dash after found eeprom (93c86)in case this is the eeprom, desolder the eeprom read it after post it hear to get pin code.ok?
my friend believe me i want to help you, my english is weak but try to do how we are write ok?
so dont worry to write and feel free to ask if you dont understand me ,i am sure in DK have good friends can help to you and write more than me....
Good Luck....

[jolidj]

tomorow i see to read the dash eeprom.
thank you for all.

[jolidj]

I read the 93c eeprom .
can i have the pin please???
With this pin what can i do??
help please.

[jolidj]

please help me.

[haroutioun]

I read the 93c eeprom .
can i have the pin please???
With this pin what can i do??
help please.
---------------------------------------------
Hello,
my friend your pin code is (01542)

[jolidj]

what can i do whith this??
acticate my key car??
i go to the dash section and activate new key??
thank you

[jolidj]

anyone tell me ,what can i insert this pin??
please :(

[haroutioun]

what can i do whith this??
acticate my key car??
i go to the dash section and activate new key??
thank you
-----------------------------------------------
OK,
i dont for get to you.but i have many work in my garage....
1) you must to go to dash (17)
2) in the login write (01542) after go to
[Adaptation - 10]
Enter 050 in "Channel Number".after use the PIN of the CAR.
(00108) ok, above our friend kokkinos panos he writ to you how and he give to you the link.Ross-Tech: Home (http://www.ross-tech.com/)

[jolidj]

nice. all ok thenk you very much.

[gadroulll]

i have a similar problem here .
the car working . car goes to a be painted.
suddenly the car stop working and there is a immo light blinking.
i have vag commander i read the pin code from dash.
i make reset ecu .
i program succesful the keys .

but nothing.

i do it with sbb ,vagtach o ,all the same results ,
all programed succesfully and the key still blinking.

i do the same with a second hand ecu , also the same .

when i read the dashboard has fault that the engine ecu has problem.
when i read the ecu it says that ecu has been blocked .

the dealer says the ecu to be changed.

does anyone has here a advise or a eeprom 29f400 and 95080 from ecu that is not blocked?

does anyone knows how to unblocked the ecu?

i know the best way is a emulator to try .

[haroutioun]

i have a similar problem here .
the car working . car goes to a be painted.
suddenly the car stop working and there is a immo light blinking.
i have vag commander i read the pin code from dash.
i make reset ecu .
i program succesful the keys .

but nothing.

i do it with sbb ,vagtach o ,all the same results ,
all programed succesfully and the key still blinking.

i do the same with a second hand ecu , also the same .

when i read the dashboard has fault that the engine ecu has problem.
when i read the ecu it says that ecu has been blocked .

the dealer says the ecu to be changed.

does anyone has here a advise or a eeprom 29f400 and 95080 from ecu that is not blocked?

does anyone knows how to unblocked the ecu?

i know the best way is a emulator to try .
--------------------------------------------------
Dear,
try to read the fault codes with your scan tool, if you can do (auto scan) and post it hear.
to know what hapen in your car maybe we can help you...

[gadroulll]

my problem is that may be a problem by the welding of the painter. the dashboard actually can not access the immo data of ecu .
i have not check the eeprom yet in the programmers

the ecu has no fault data after the clear ,but the dashboerd has .