Mercedes W210 probem with EIS

[unar]

I have problem with w210 2001year 2,2cdi. key unlock ESL but dont unlock EIS and dont turn eis.

orig EIS - 210 545 02 08

now I have EIS with key and ESL from another car but it is from benzin, this key unlock esl and eis but starter dont crank.

new EIS - 210 545 00 08

in engine ecu i have fault P1330 - starter control, readed via autoboss v30.
I dont have nec merc key programer.
is there any way to make ECU dump worked with new EIS and ESL.

fuses checked.

What I sholud do with it?

thnks for reply

Regards
unar

[bassit]

post the original dump for your ecu
do u have das for adaptation?

[unar]

post the original dump for your ecu
do u have das for adaptation?

Sorry is there any other way to make this ecu because i dont have das.

Here is my ecu original file

[bassit]

u need das
for other tools I don't know

[sogaro]

Don't know about Autoboss but i use X431 from time to time to do some ECUs not all. However, no harm in trying. What would have been easier for you is to buy NEC programmer for key or similar too to write key files. Am almost sure you are going to have a dead car at the end of the day if you are not careful------your new set might not work

[gtmech]

Don't know about Autoboss but i use X431 from time to time to do some ECUs not all. However, no harm in trying. What would have been easier for you is to buy NEC programmer for key or similar too to write key files. Am almost sure you are going to have a dead car at the end of the day if you are not careful------your new set might not work

x431 will do ECU adaptations for merc?

[bassit]

I have problem with w210 2001year 2,2cdi. key unlock ESL but dont unlock EIS and dont turn eis.

orig EIS - 210 545 02 08

now I have EIS with key and ESL from another car but it is from benzin, this key unlock esl and eis but starter dont crank.

new EIS - 210 545 00 08

in engine ecu i have fault P1330 - starter control, readed via autoboss v30.
I dont have nec merc key programer.
is there any way to make ECU dump worked with new EIS and ESL.

fuses checked.

What I sholud do with it?

thnks for reply

Regards
unar

hello!
disold the mcu1 and mcu2 from original eis then sold them on new eis.
the car will start normally, not need das ;)
give the report

[unar]

now I have DAS and nec key prog, so what I should to do with this car?
I have readed original eis dumps and I see that first mcu is FFFFF...
anyway dumps of original EIS and ECU from this car are in attachments.
Is there way to start it without touch ESL or is there any way to read ESL via upa or xprogm?

Plesase give me some tips to make this car start.

Regards
unar

[adikk]

now I have DAS and nec key prog, so what I should to do with this car?
I have readed original eis dumps and I see that first mcu is FFFFF...
anyway dumps of original EIS and ECU from this car are in attachments.
Is there way to start it without touch ESL or is there any way to read ESL via upa or xprogm?

Plesase give me some tips to make this car start.

Regards
unar

Try write correct damp to EIS 1 and write new key (4-8 not used) and post resalt. Pass in PM
BR

[unar]

Try write correct damp to EIS 1 and write new key (4-8 not used) and post resalt. Pass in PM
BR

Thank You for dumps tomorrow I will give back results.
And what about engine ECU, do I need reprogram it or not?

Regrds

[lateef]

autoboss can do adaptation too

[adikk]

Thank You for dumps tomorrow I will give back results.
And what about engine ECU, do I need reprogram it or not?

Regrds
If EZS work OK, You dont need reprogram engein ECU. But if You dont have equipment for work to ESL, pls write ONLY one key (for ezample key#4) and post resalt.
BR
If EZS dont work, read and post damps of new EZS

[unar]

autoboss can do adaptation too

I try to find but no result. I will deep try again today

[unar]

Try write correct damp to EIS 1 and write new key (4-8 not used) and post resalt. Pass in PM
BR

Your dumps are good , I put Your dump to mcu1 and program key4, EIS unlock ESL unlock
Can You write what program do You use for this?

Best Regards
unar

[fernandoherocha]

I esou a problem with the W210 mcu2 FFFFFF is erased and now I do not I write the key if I change the dumps and mcu1 mcu2 conseguri will I solve this problem?

[AC_SHNITZER]

try to virginize ecu and personalize with new esl / ezs

[vanya86]

Hello friends.
I have NOIMMOlt ori tool but i don't have any tool to read nec from key N4

Is possible that someone make me from EIS dump repaired dump for Key N4, i have tool only to write NEC.

Please help.

Thank you

[nikinik]

I have problem with w210 2001year 2,2cdi. key unlock ESL but dont unlock EIS and dont turn eis.

orig EIS - 210 545 02 08

now I have EIS with key and ESL from another car but it is from benzin, this key unlock esl and eis but starter dont crank.

new EIS - 210 545 00 08

in engine ecu i have fault P1330 - starter control, readed via autoboss v30.
I dont have nec merc key programer.
is there any way to make ECU dump worked with new EIS and ESL.

fuses checked.

What I sholud do with it?

thnks for reply

Regards
unar


You can make ecu file Virgin with immokiller and then with DAS
go to Ecu and Replace ECU options in adaptation menu.
I have same situation here now ,but maybe my DAS is brocken
and when i start procedure and das say switch ignition off ,i switch ignition off but nothing happend.Das cant see the ignition off,and no success .i dont know why?
Many colleges test this without problem,dont know why i cant finish the procedure.