PDA

View Full Version : MAGPRO2 CL*N TEST OK IN VEHICLES



psico
31st August, 2011, 11:13 AM
Hi

I thought about going by making a list of vehicles we are doing and if things go wrong, can be divided into the euro clone and Chinese clone.

I personally I have a euro clone.

ALFA GT 1900 16V 150CV---------EDC16+ R/W OK
AUDI A4 2.0TDI 140CV -----------EDC16+U31 R/W OK
FORD FOCUS 1.8 TDCI 115CV-----SIEMENS SID202 R/W OK
OPEL ZAFIRA 1.9 CDTI 150CV-----EDC16+ CAN BUS R/W OK
OPEL ASTRA 2.0 T 190CV----ME 1.5.5 R/W OK
PEUGEOT 207 1.4 HDI 68CV----EDC16+ CAN R/W OK
PEUGEOT 207 1.4 8V 75CV------JHONSON VALEO CAN R/W OK
PEUGEOT 307 2.0HDI 110CV----EDC15C2 R OK W BLOCK no problem with slow speed, i selected max.
RENAULT MEG 1.5 DCI 82CV----DELPHI K R/W NO
SEAT LEON 1.9 TDI 105CV----ECD16+U34 CAN R/W OK
SKODA OCTAVIA 1.9TDI 105----EDC16U R/W OK
VW GOLF 1.9 TDI 105----EDC16+ R/W OK
Clon chinese VW GOLF R32 250CV----ME7.1.1CAN R/W BUT NO START.........
MERCEDES VITO 110CDI ----EDC15C0 R/W OK
CITROEN PICASSO 2.0 HDI 2007 SIEMENS SID803A READ OK
PEUGEOT 307 HDI SIEMENS SID801 WRITE OK
ALFA BRERA 2.4 JTDM BOSCH EDC16 C39 READ AND WRITE OK------------read 45 min
MB ML 3.0 2009 224CV EDC16+ READ AND WRITE OK , for no problems fans engine off .
FIAT DUCATO 2.0 SIEMENS SID803 CAN READ WRITE NO PROBLEMS READ 2MG.

With the collaboration of all, we can avoid many headaches.

i always slow speed for no problems.:wink::wink:

With 5.5 update

Read and write mazda 1.6 group psa , read and write ok.

bazare
31st August, 2011, 12:00 PM
Or you can buy the original and avoid ALL headaches and also have support! Plus the new version v5.0 don't work with clones.

psico
31st August, 2011, 02:16 PM
5.0 in clone....time ..time friend,

I do not belittle people who have the original, I do not work on this, just a hobby.
If reprogramming my job I would not hesitate in buying a Galletto 2.

My intention is that people who are starting or not your job does not have this problem or has the minimum.

Magpro2 and x17 is good good machine and no more cost for the coverage you have.

psico
2nd September, 2011, 08:23 AM
FORD FOCUS CMAX 1.8 16V TDCI SIEMENS SID202A R OK

bambula tuner
29th October, 2011, 11:38 PM
Hello at all (o:

I have read & write the fallow ECUs

-Fiat Stilo 1.6 16V Marelli 5NF
-Fiat Ducato 2.3 & 2.8 JTD EDC 15
-Fiat Ducato 2.3 JTD EDC16C39
-Fiat Panda 1.2 8v Marelli 5af
-Fiat Croma FL 2009 2.4 JTD EDC16C39
-Fiat Doblo 1.9 JTD EDC16C39
-Fiat Bravo 1.4 & Grande Punto Abarth SS 1.4tjet 180 HP -Bosch ME7.9.10 READ IN Boot mode writing via OBD but -works only with fast Speed Option
Alfa GT 2.0 JTS Bosch MED7.1.1 Read & Write in Boot Mode
-Alfa 159 EDC16C39 2.4 JTD & 1.9 JTD 6 diffrent Cars

- Golf 5 R32 Bosch Me7.1.1. read & write on CAN via OBD

The only one ECU Bosch EDC16U from a VW Transporter T5 2.5 TDI i cant read & write via OBD. with Galletto i can read but no write this ECU any Idea?

Mario4044
29th October, 2011, 11:42 PM
DO with BDM100

bambula tuner
29th October, 2011, 11:59 PM
i have a bdm 100 Clone but i hear,that somes has wrong connection inside. Do you now how can i check this ?

thanks for the quickly reply

serguei
30th October, 2011, 07:41 AM
I read and write clone MPPS 5.0 via OBD: T5 1.9TDI BRS 2008 and T5 2.5TDI BNZ 2006.

psico
30th October, 2011, 10:41 AM
T5 is best read and write bdm.

jejevfr
30th October, 2011, 01:56 PM
peugeot 407 2.0 136cv , dcm 3.4 OK
picasso 2.0 hdi 90cv edc15 OK
seat leon 150cv tdi edc15 OK

test recovery edc15p tdi 100 OK

serguei
30th October, 2011, 02:10 PM
VW Touran 2.0 TDI BMM EDC16U34 2007 read OK.

sukkamotton
1st November, 2011, 06:47 AM
hello whats recomended for USA makes ford dodge and gm . what interface and what software any help will be apreciate

psico
1st November, 2011, 04:41 PM
Hi ,for ford good interface is powergate .

psico
25th December, 2011, 11:39 PM
ANYONE has read and written a sid803a siemens in can of citroen hdi?

chris_e36_328
26th December, 2011, 12:07 AM
Posted in other thread but no replies there..
Hi, got my MagPro2 delivered a few days back. A few questions for those more familiar with it:

1. is it safe to use the clone with v2.42a even though it was delivered with 4.1? I am annoyed with the fact I have to request key files from my supplier each time I change the laptop. How does 2.42 goes around this? has anyone got keygen for the 4.1?

2. My interface came in a black alu case, but looking at the pictures the PCB seems same as the one in blue alu listed in this thread ealrier on. To be frank I see no differences between these other than solering quality. Any one can elaborate?

3. Can anyone onfirm whether the Kess V1 clone HW is any better, stable or reliable than the MagPro2? There seem to be slight differences between these two.

4. re 803A: What is your experience with this SID? Reading/writing? Anyone has any connectivity issues with Kess v1 or MagPro or are these safe to use on the 803 and 803A?

ominimicu
26th December, 2011, 02:01 AM
ANYONE has read and written a sid803a siemens in can of citroen hdi?

I did, the MCU only for DPF removal.

psico
26th December, 2011, 09:04 AM
I did, the MCU only for DPF removal.

thanks friend,

REad and write with magpr* clon??

Mario4044
28th December, 2011, 08:09 PM
Usually in mirror shape.

chris_e36_328
29th December, 2011, 01:33 AM
Mate, the 10pin IDC BDM socket pinout is a major pain. They differ from one another. The pinout is the same actually, it is the connector that's mounted on the probe's PCB the other way round. For example the Bosch probe from Optican has same layout as DimSport one, but the alientech's probe has got the IDC socket mounted the other way round.
I am putting together my own set of probes as I have enough of working out which probes to buy and which connector to use as I have gen. 555pro as well as clone bdm100.

cosmind
18th January, 2012, 07:23 PM
what is the time for read and write edc16c39 from fiat, alfa, pug or citroen ?

ross79ta
19th January, 2012, 01:19 AM
what is the time for read and write edc16c39 from fiat, alfa, pug or citroen ?

Edc16c19, like Marelli 6JF, around 40 minutes to read, and around 2-3 minutes to write.

psico
19th January, 2012, 09:25 AM
Posted in other thread but no replies there..
Hi, got my MagPro2 delivered a few days back. A few questions for those more familiar with it:

1. is it safe to use the clone with v2.42a even though it was delivered with 4.1? I am annoyed with the fact I have to request key files from my supplier each time I change the laptop. How does 2.42 goes around this? has anyone got keygen for the 4.1?

2. My interface came in a black alu case, but looking at the pictures the PCB seems same as the one in blue alu listed in this thread ealrier on. To be frank I see no differences between these other than solering quality. Any one can elaborate?

3. Can anyone onfirm whether the Kess V1 clone HW is any better, stable or reliable than the MagPro2? There seem to be slight differences between these two.

4. re 803A: What is your experience with this SID? Reading/writing? Anyone has any connectivity issues with Kess v1 or MagPro or are these safe to use on the 803 and 803A?

hi, if your clone is the one with the RJ45 to obd2 , you can use soft 4.2a smoothly and without serial.
this soft is ok.


I recently sid803a Realize a c4 without problems.

chris_e36_328
20th January, 2012, 03:28 AM
Hi Psico, thanks for info. Yes, its the RJ45 with one can line missing. Did the 803A with my mates Kess2 just to stay on the safe side for now. Could anyone confirm that if PSA 803A is all good it's going to be the same for 803A on Ford? thanks

pablo1971
4th March, 2012, 01:34 PM
can anyone help me,ive read a 2007 range rover sport 3.6 tdv8---the read was ok,now ive got a tuned file,but when i open it,i get a error message----WARNING-INVALID FILE---obv i thought there was a problem with tuned file but that is ok.....so i tried to write back the original file from the car,and im still getting the same error message,this is the first time ive ever seen the error message on the magpro2(clone).......just wondered if anyone can help...

psico
4th March, 2012, 05:35 PM
hi

I see your selec medium speed, please read in mode slow and, test , write ori in slow speed.

Where is your version of soft?

psico
4th March, 2012, 05:39 PM
New link of soft magpro2 version 4.2a

without serial

https://rapidshare.com/files/3532048577/setupMAGpro2_42a_portugues.rar

pablo1971
4th March, 2012, 07:54 PM
psico-thanks for the speedy reply.....and the software i am running is the 4.2a.....i will try the write back at slow speed-but,if i pick the original to write back i am still getting a error......normally,if you write back at a fast speed you can open and load the file into magpro,and as it starts to write the file back it will error,i am getting a error as soon as magpro as seen the original file...

clio_williams
13th March, 2012, 02:33 PM
best sw for this euro clones is v3.0 i have made many cars via this tool never had anyproblem about 2 years... what is important is to check if tool calculates chk for that ecu... always try in slow or medium speed...

psico
14th March, 2012, 11:41 PM
best sw for this euro clones is v3.0 i have made many cars via this tool never had anyproblem about 2 years... what is important is to check if tool calculates chk for that ecu... always try in slow or medium speed...

my clon , perfec vers 4.2a ,alu box, i always slow or medium speed

sarkann
20th March, 2012, 11:45 AM
Ford Transit MY2010 2.4TDCI ECU Visteon Read OK. Didn?t try to write.
Punto 1.2 60HP Marelli IAW59F R/W OK.

psico
20th March, 2012, 09:33 PM
Ford Transit MY2010 2.4TDCI ECU Visteon Read OK. Didn?t try to write.
Punto 1.2 60HP Marelli IAW59F R/W OK, after starting MIL is blinking.

where is your version of soft??
Where is your clon? conexion rj45 or other?
You read in slow?

I read and write perfec visteon 2.4 ford.... and magpro correct checksum good.

sarkann
25th March, 2012, 11:58 AM
Software Magpro2. Connection USB. Blinking MIL was because of learning process after rewriting ECU - so everything is OK.
Another cars:
CMAX SID 803 1024+452 kB R/W ok
CMAX SID803A 2048 kB R/W ok
Renault EDC16c34 CAN Read OK, I didn?t try to write untill now
OPEL EDC16C39 R/W OK
Alfa EDC16c39 R/W OK
Kia EDC16+ R/W OK

psico
25th March, 2012, 11:09 PM
Software Magpro2. Connection USB. Blinking MIL was because of learning process after rewriting ECU - so everything is OK.
Another cars:
CMAX SID 803 1024+452 kB R/W ok
CMAX SID803A 2048 kB R/W ok
Renault EDC16c34 CAN Read OK, I didn?t try to write untill now
OPEL EDC16C39 R/W OK
Alfa EDC16c39 R/W OK
Kia EDC16+ R/W OK

ok, thanks friend.

ZIZZOU
26th March, 2012, 08:22 PM
Hi guys
i don't know what's happen to my magpro2 device!!
every time i tray it,it can only read ID ecu(SW and HW)
but if i try to read the dump ,it failled,and a window is open and say that may be i have selected a wrong ecu ....and that i have to try to disconnect the device and try it again
like it happen to me with this DACIA LOGAN 1.5DCI with DCM1.2 ecu
before this it happened the same think with peugeot207 petrole with valeo ecu ,and with fiat MAREA with BOSCH ME2.1
is there a suggestion to solve my probleme?
http://i43.servimg.com/u/f43/16/03/79/30/sans_t14.jpg

sarkann
17th April, 2012, 08:24 AM
I have some problems, too.
Zafira B, EDC16+ - first write always bad checksum, Second time OK.
Alfa EDC16c8 - no read/no write - it writes "illegal acces" -solved by mpps
Marea EDC15c2 E2 - fail during writing, need to solder :(
Chrysler Voyager - edc15 2.5CRDI - illegal acces. No R/W. - solved by mpps

sarkann
17th April, 2012, 08:26 AM
Hi guys
i don't know what's happen to my magpro2 device!!
every time i tray it,it can only read ID ecu(SW and HW)
but if i try to read the dump ,it failled,and a window is open and say that may be i have selected a wrong ecu ....and that i have to try to disconnect the device and try it again
like it happen to me with this DACIA LOGAN 1.5DCI with DCM1.2 ecu
before this it happened the same think with peugeot207 petrole with valeo ecu ,and with fiat MAREA with BOSCH ME2.1
is there a suggestion to solve my probleme?
http://i43.servimg.com/u/f43/16/03/79/30/sans_t14.jpg

Marea ME2.1 couldn?t be read/write by OBD. Other cars I don?t know.

mbtuning
17th April, 2012, 08:44 AM
It's easy ... mess around with clones and buy the original. Already version 5.2 in the genuine tool. And everything is working like it should.

subarurex
10th June, 2012, 01:15 AM
Hi

Have anyone do a read/write Renault meganeII 1.5 DCI 85cv (Renault Delphi E4 dci CAN) ?

AGS
10th June, 2012, 05:24 AM
Hello,
can anybody try to read via BDM sid803 peugeot/citroen 407,307,picaso,c5... ecus(Mpc 555/6),and write by magpro2 clone?
how is feedback?
thanks fo reply.
best regards

psico
10th June, 2012, 10:57 AM
Hello,
can anybody try to read via BDM sid803 peugeot/citroen 407,307,picaso,c5... ecus(Mpc 555/6),and write by magpro2 clone?
how is feedback?
thanks fo reply.
best regards

Yes , no problems , remember always in slow mode read and write , no problems.

sid 803 sid803a read and write.

subarurex
10th June, 2012, 02:18 PM
No one have test the Magpro2 clone on Renault Delphi E4 dci CAN?

Smac_a
10th June, 2012, 05:18 PM
No one have test the Magpro2 clone on Renault Delphi E4 dci CAN?

I only read it... As for write I can't say because I never tried.

Btw how come you always have to use slow speed? Does anyone have a solution - I already changed lm339 but only reads/writes slow speed...

Regards,
Smac_a

AGS
10th June, 2012, 05:19 PM
Yes , no problems , remember always in slow mode read and write , no problems.

sid 803 sid803a read and write.
In my magpro sid803 only write by obd ,not ready function by obd

Smac_a
10th June, 2012, 08:35 PM
That is normal, I tried couple of versions of software and reading is not posible...

Regards,
Smac_a


In my magpro sid803 only write by obd ,not ready function by obd

spawns3
10th June, 2012, 09:05 PM
Sid 803aCAN , can read and write

Smac_a
10th June, 2012, 09:08 PM
Sid 803aCAN , can read and write

Sorry - I forgot! On can it's posible!

Regards,
Smac_a

AGS
11th June, 2012, 03:40 AM
that sid803A i know what no problem read and write! Oldest cars do it via "k-line",newest via "can".
Sid803A have only flash 2mb and eeprom at ecu.
But sid803 have flash,external memory mpc555/6 where is all map's and fap calibrations,and etc...and eeprom fore immo,configurations....
I did not try write mpc555,so ask that question maybe anybody tried to write.(read by bdm-write via obd)
best regards
thanks for all:top:

AGS
12th June, 2012, 05:03 AM
Tested pug 308 1.6hdi edc16c34 full can!Not work magpro2,after reflash wrong make checksum magpro2!BDM +winols correct chk as bad car not start! Only bdm tool make correct chk and car start ok.:cool:

bambula tuner
24th February, 2013, 06:53 PM
Tested pug 308 1.6hdi edc16c34 full can!Not work magpro2,after reflash wrong make checksum magpro2!BDM +winols correct chk as bad car not start! Only bdm tool make correct chk and car start ok.:cool:

The problem is that magpro 2 partial flashing and win ols make the checksumm total. I had the same problem with a g. Punto bosch edc16c39. Its easy to fix only dont make the checksumm correction not with winols leave the magpro calculate. Then works fine. You can also make on a modified file the checksumm on original stand in winols. You dont need editing again

pablo1971
24th February, 2013, 07:11 PM
Mate, the 10pin IDC BDM socket pinout is a major pain. They differ from one another. The pinout is the same actually, it is the connector that's mounted on the probe's PCB the other way round. For example the Bosch probe from Optican has same layout as DimSport one, but the alientech's probe has got the IDC socket mounted the other way round.
I am putting together my own set of probes as I have enough of working out which probes to buy and which connector to use as I have gen. 555pro as well as clone bdm100.



the bdm100 is a pain......best is to get a couple of ecu from scrap yard and practise....make a pogo adaptor,and go for it...

flixuno
24th February, 2013, 07:31 PM
disculpas por my ingles
audi a-4 2.0 tdi leer y escribir ok
bmw E46 gasolina 170 cv leer y escrivir ok
mag pro funciona 60% de vehiculos sobre todo gasolina

flixuno
24th February, 2013, 07:34 PM
sorry for my English
audi a-4 2.0 tdi literate ok
bmw E46 170 hp petrol and read this written ok
pro mag works 60% of all vehicles on gasoline

psico
25th February, 2013, 12:08 AM
Magpro works very well and is stable, I have done many cars with it, and I could not have been some EDC15 do not really care because it can be done with lower cost tools.

For those who dont have even the software update 5.5

https://www.dropbox.com/s/2gwr8es5aec8k6b/MAGPro2%20upgrade%20V5.5%20for%20V4.2%20PSICO%20.r ar

heteromies
21st April, 2013, 04:52 PM
Is this update 4.2 to 5.5 working one? Have any member all ready test it? General version is that 4.2 and after that clone newer is difficulted by owner

J_amb_o
21st April, 2013, 07:20 PM
No, it isn't

mauronow
21st April, 2013, 10:54 PM
hi....where I buy good clone of Magpro 2???

ZIZZOU
22nd April, 2013, 09:09 AM
Tested pug 308 1.6hdi edc16c34 full can!Not work magpro2,after reflash wrong make checksum magpro2!BDM +winols correct chk as bad car not start! Only bdm tool make correct chk and car start ok.:cool:

MAGpro2 read/write peugeot 308 1.6 HDI EDC16C34 very well
first,magpro2 ask you to save injectors codes ,then you can read the flash,it take some times,about 10minutes
and write flash very fast ,
i had read/write with MAGpro2 citroen berling 1.6HDI years2011,peugeot 207 1.6 HDI ,peugeot 206 1.4 HDI,and work like a charme
you can also programme the injectord codes that you had saved with magpro2,no need pp2000 or lexia
and i attached the flash of 308 1.6HDI read by MAGpro2

heteromies
22nd April, 2013, 10:17 AM
MAGpro2 read/write peugeot 308 1.6 HDI EDC16C34 very well
first,magpro2 ask you to save injectors codes ,then you can read the flash,it take some times,about 10minutes
and write flash very fast ,
i had read/write with MAGpro2 citroen berling 1.6HDI years2011,peugeot 207 1.6 HDI ,peugeot 206 1.4 HDI,and work like a charme
you can also programme the injectord codes that you had saved with magpro2,no need pp2000 or lexia
and i attached the flash of 308 1.6HDI read by MAGpro2

What version v4.2 or v5.5?

Clone?

Where its buyed?

ZIZZOU
22nd April, 2013, 11:01 AM
v4.2, clone of corse:laugh: from china
i got it from MERCIS, a DK member here,he has a good china clone
best regard's

kosiik2
29th June, 2013, 11:15 PM
is good?
magpro2 chiptuning tool Mag pro 2 v4.2 (http://www.obd2tuning.com/magpro2-chiptuning-tool-mag-pro-2-v42-p-809.html)

psico
29th June, 2013, 11:59 PM
hi

this is good. use new software 4.2 and 5 and run pefect.

MAG PRO2 V4.1 OBD2 ECU TUNING TOOL (http://www.esobd2.com/wholesale/mag-pro2-obd2-ecu-tuning-tool.html)

H.Wessel
30th June, 2013, 02:51 PM
hi

this is good. use new software 4.2 and 5 and run pefect.

MAG PRO2 V4.1 OBD2 ECU TUNING TOOL (http://www.esobd2.com/wholesale/mag-pro2-obd2-ecu-tuning-tool.html)

Could you upload 4.2 soft without license? you old link is died friend

Thanks in advance!
H.W

psico
30th June, 2013, 03:23 PM
here, without license, only install.

https://www.dropbox.com/s/wb8fchjwqvevji7/setupMAGpro2_42a%20RPERFOMANCE.rar

H.Wessel
30th June, 2013, 04:14 PM
here, without license, only install.

https://www.dropbox.com/s/wb8fchjwqvevji7/setupMAGpro2_42a%20RPERFOMANCE.rar

You are the best! thanks friend

flixuno
30th June, 2013, 04:56 PM
hi!
In seat toledo year 2002 1600 16v petrol read and write ok
renault clio 1500 dci not read and not write
renault 2000 dci year 2009 140 cv read and write ok

icezero2010
1st July, 2013, 10:01 AM
use with mpps slow speed and it works

H.Wessel
15th July, 2013, 10:46 AM
hi

this is good. use new software 4.2 and 5 and run pefect.

MAG PRO2 V4.1 OBD2 ECU TUNING TOOL (http://www.esobd2.com/wholesale/mag-pro2-obd2-ecu-tuning-tool.html)

I just recieved this MagPro2, I test with you soft and doesn't work(Because ori need license and I don't have it yet)
Soft open fine but when It try to connect after push "Data" button it say that ecu is not found.
Do you know why?

Regards
H.W

psico
15th July, 2013, 08:37 PM
only use drivers my software, run perfect test with more magpro 2, i think is problem drivers.


before run software conect obd2 in vehicle 12v and conect usb , run software and light red run 5 sec and open software.

test and report.

H.Wessel
15th July, 2013, 11:36 PM
Btw, does someone have pinout from rj45 port to obd?, I just had to rework mine but not trusting is wired ok..

Edit: K-line edc15v works fine at slow and medium speed, but edc16u34 doesnt work yet. Anybody could see the pinout from rj45 to obd to make a good cable?

Thanks

H.Wessel
17th July, 2013, 12:11 AM
I repaired obd cable, was wrong, now I can read edc16u34 only if I choose edc16cp34 but it can not write, if I choose edc16u34 program give "error comunication ecu", so for me works worse than a 10$ mpps cable...

psico
17th July, 2013, 10:46 PM
image of rj45 to obd2, test.

Very important

always speed in slow

ludbe
29th July, 2013, 01:29 PM
What about MAGPRO CLONE and psa group injector codes? does magpro save codes before writing and after writing wrote them back or? Does exist EU clone or only chinese?

H.Wessel
29th July, 2013, 04:46 PM
image of rj45 to obd2, test.

Very important

always speed in slow

Nothing, my magpro doesnt work with can cars...I also reflow with hot air the pcb and allwats the same problem,
thanks for your help.

2200
19th September, 2013, 12:32 AM
where is v5? no link work

psico
19th September, 2013, 09:52 PM
where is v5? no link work


here

https://www.dropbox.com/s/qrfqkixrl8ruwjm/MAGPro2%20upgrade%20V5.5%20for%20V4.2%20PSICO%20.r ar

update to 5.5

2200
20th September, 2013, 12:23 PM
Magpro works very well and is stable, I have done many cars with it, and I could not have been some EDC15 do not really care because it can be done with lower cost tools.

For those who dont have even the software update 5.5

https://www.dropbox.com/s/2gwr8es5aec8k6b/MAGPro2%20upgrade%20V5.5%20for%20V4.2%20PSICO%20.r ar

make please a good picture of your PCB i know why edc15 is not good working.
the software is from user TribleX80 and this version you have give me link is not the last good one :-) .
regards

psico
21st September, 2013, 04:12 PM
its a problem of all magpro clone, any edc15 not run..

2200
21st September, 2013, 04:39 PM
its a problem of all magpro clone, any edc15 not run..

with mod all edc15work

make a picture....pcb

heteromies
21st September, 2013, 05:45 PM
What about MAGPRO CLONE and psa group injector codes? does magpro save codes before writing and after writing wrote them back or? Does exist EU clone or only chinese?

I am intereted also, is there EU clone available !?!??

Please send link, price PM....

psico
21st September, 2013, 11:43 PM
this is magpro 2 eu clone 220628

2200
22nd September, 2013, 03:57 AM
one Resistor is missing :joyous: on your board

2200
22nd September, 2013, 08:43 PM
check this :top:

psico
22nd September, 2013, 09:46 PM
check this :top:


where is the pass?

thansk.

elosomaloso
13th April, 2014, 11:08 PM
have pm... Thanks

jonixins
5th May, 2014, 12:15 AM
...........

mandaxcdd
13th August, 2014, 11:04 AM
Hello .I have the same problem with my Magpro2 on Edc15 .Where is the magic resistor for this problem? Thanks in advance !

mandaxcdd
6th October, 2014, 11:29 AM
No answer for a long time ago .................................... no comment

2200
6th October, 2014, 05:27 PM
R6 = 10 Kohm

mauronow
6th October, 2014, 06:28 PM
R6 = 10 Kohm
Hi mate... these resistor afect other protocols? ?? Or only edc15?
Thanks

2200
6th October, 2014, 06:40 PM
Hi mate... these resistor afect other protocols? ?? Or only edc15?
Thanks

K-Line function

mauronow
6th October, 2014, 07:24 PM
K-Line function
Thanks.. you magpro is stable?
Much protocols? What soft you use?

mandaxcdd
7th October, 2014, 11:17 AM
Thanks my friend.Today will try with R6 .Magpro is very good on italian cars .Where Galetto v53 not work ,Magpro is ok .On Fiat Bravo 1.4 tjet 120cp with Kline Galetto is not good,,,,,,,,Magpro write ok. Very stable with 4.2 software.

mandaxcdd
24th October, 2014, 09:59 AM
Now it works .The "God ressistor " is very important for edc15.I put that ressistor with a switch just for edc15 because the rest of ecu is works fine without R6. Thanks again

grigore4443
11th December, 2014, 01:25 AM
MAGPRO2 software please!!!can possible without license . Thanks in advance !!

mandaxcdd
11th December, 2014, 09:11 AM
Download from here ,is ok magpro2 chiptuning tool Mag pro 2 v4.2 (http://www.obd2tuning.com/magpro2-chiptuning-tool-mag-pro-2-v42-p-809.html)

cotymoto
30th August, 2015, 11:18 AM
mate ford cmax 1.8tdci 16v not exist. only 8v. mppsv13, read perfectly obd.