Open PLI Oscam & CCcam UK Ready EPG Mapped Backup

[pogo2009]

http://linuxsat-shares.com/images/imported/2011/03/1.gif

Open PLI Of 25/8/11

OSCAM 1.10rc-svn build #5921 & CCcam 2.13

Preinstalled with 0963 Configs
Radio Times EPG Is Ready Mapped !


Ready to Run, Just Insert Your Card !

No need to enter boxkey as oscam will detect your card automatically.

Card speed automatically clocked to 5mhz

Image Contains UK bouquets & will store 2 days worth of epg data, the

following bouquets are already mapped for you.

Sports
Movies
Documentary's
Entertainment
Lifestyle
Kids
Music

http://img21.imageshack.us/img21/241/moviesj.png

To download epg simply press yellow select

dreambox epg config then press yellow to

retrieve.

http://www.digital-kaos.co.uk/forums/IMG]http://img545.images%20%20hack.us/img545/2075/newsn.png
NOTE: 30 seconds after boot both cams are restarted with oscam

starting first, this is to eliminate any problems with oscam not

finding card reader.

Installation

Install Via Flashwizard pro (attached )
1. Download Image & exract to desktop.
2. Download & start Flashwizard pro
3. Fill in DM configuration Then simply drag image file Into programme

as shown below
4. Enjoy, image will be flashed in under 2 minuetes

http://www.digital-kaos.co.uk/forums/[IMG]http://img545.imageshack.us/img545/8750/flashwizard.pnghttp://img545.imageshack.us/img545/8750/flashwizard.png
Enjoy

image

Multiupload.com - upload your files to multiple file hosting sites! (http://www.multiupload.com/PWG39HTFC8)

flashwizard

Multiupload.com - upload your files to multiple file hosting sites! (http://www.multiupload.com/4KDM7QGXUX)

[satsmo]

Nice post but seen it elsewhere are you the OP? I will say you are as I have seen previous.

[pogo2009]

Nice post but seen it elsewhere are you the OP? I will say you are as I have seen previous.

Yes satsmo it is my work, we have been here before lol.

[satsmo]

I will let you away with it once more, stop doing that :)

Stickied also, I can see it been put to good use.

[alom5]

will this work on 800se sim 2.1

[mtv1]

simples m8 NO :)

[ade786]

hi is this clone safe
/

[mtv1]

all pli images are mate :) just check the size of the file if it looks too big then its not safe ;)

[pogo2009]

hi is this clone safe
/

It was made on a clone so no worries there mate,
all passwords & ports are default root & dreambox.

Oscam webinfo

http://ip_of_dreambox:8888/

User =admin
Pass = admin

[southpaw]

just to confirm , oscam will read card , then hand sharing to cccam , so its just a matter of entering port and f-lines to cccam.cfg and all up and running ,
if so , nice job op , this will save a lot of people a lot of hassle , nice of you to share your work

[pogo2009]

just to confirm , oscam will read card , then hand sharing to cccam , so its just a matter of entering port and f-lines to cccam.cfg and all up and running ,
if so , nice job op , this will save a lot of people a lot of hassle , nice of you to share your work

Yes this is correct mate, just make sure you remember all passwords are default at the moment so make sure all is secure first if you intend using it for c/s.

[mtv1]

:hmmmm: sorry mate went to flash a spare 500s i have hangs on restoring image please wait :( followed your very good instructions , has this happened before and hate to be awkward but have you this as an image file for dreamup :D

[pogo2009]

:hmmmm: sorry mate went to flash a spare 500s i have hangs on restoring image please wait :( followed your very good instructions , has this happened before and hate to be awkward but have you this as an image file for dreamup :D

I do have it in .img format but had no pc with a serial handy to test it so used flashwizard. I know a lot have flashed successfully using flashwizard so ill upload the .img file now & pm you a link.

you can be guinea pig lol

[mtv1]

i am that lol nice one m8 ;)

[mtv1]

awwww man thats the dogs :) much appreciated :) will you post it for other thicko's like m8 ;) also would you mind if i put a link on my siggy ?? lol

[pogo2009]

Glad it worked mate & thanks for testing it, here is the link for anyone who has probs with flashwizard.

backup.img - 4shared.com - online file sharing and storage - download (http://www.4shared.com/file/AFr1w3tQ/backup.html)

Thank pli for the image not me lol, all i did was share a backup i made i am glad you like it mate. Feel free to share it as you like the point of posting it was exactly for this. The last backup i made appeared on ebay so the more people find it for free the better.

:cheers:

[viru2375]

Hi, I have DM500s with gemini image and all the same settings which my friends DM500s got but my DM500s is not showing some channels can u please help ?????

[Data7]

Pogo m8 can tell me if your image is easy to just enable oscam to be a client only. as the oscam is twice as fast at handling the emu's than cccam. thanks in advance.

[badboi79]

After all the crashing trying to flash this with FWP I eventually did a dreamup with it and must say I did not like it at all.

Just my two pence worth guys..

[pogo2009]

Hi, I have DM500s with gemini image and all the same settings which my friends DM500s got but my DM500s is not showing some channels can u please help ?????

I think you would have more chance of an answer starting a separate thread for this one mate.

[Data7]

Pogo m8 can tell me if your image is easy to just enable oscam to be a client only. as the oscam is twice as fast at handling the emu's than cccam. thanks in advance.

[pogo2009]

Pogo m8 can tell me if your image is easy to just enable oscam to be a client only. as the oscam is twice as fast at handling the emu's than cccam. thanks in advance.

You will need to install oscam dvbapi for this you will find all the info you need on oscam wiki.

[southpaw]

pogo , does this backup have ecmwhitelist enabled ?

[pogo2009]

No it doesn't mate as it changes frequently so may cause problems for the less experienced, if you want to use it just add the line to the reader section of oscam.server. The oscam version will support it.

[scotty001]

hi
just tried to load this and lost everything, no channels not even freeview. i was using jade pli 2 image. can anyone help please.

cheers

[micflair]

Yes this is correct mate, just make sure you remember all passwords are default at the moment so make sure all is secure first if you intend using it for c/s.

Alright mate, just a quick question - probably a stupid one - but why did you make it so cccam does the sharing and not just oscam doing both reading and sharing? Any particular reason? Anychance of some instructions on how to make it just oscam only? Ive tried the obvious menu option of default cam/readers but youve got it auto booting to cccam regardless I think..

Also - thanks for the image, awesome work ;)

[musky1970]

yo,mega newbie here,my dm500 has pli jade on it,is there any advantage in me putting this image on,or is it just to help read a card?ta

[SGTFlipFlop]

Flashed this image, Will give it a whirl

[Ureyesonly]

thanks for the image, i'v tested it but movies & sports not clearing?

Edit: never mind sorted, thanks.

[Fellianis Wig]

When you flash with the flashwizard are you supposed to get the flashwizard 2.5.9 screen everytime you reboot?

[donkeyboy]

Morning guys

Ok i trieed to flash this img last night i got my self an old lappy with null modem connection on the back plus i have the correct cable aswell /got flashwizard pro install
now when it comes to flash it connection error check parameters which i think ive done correctly
name of box /dreambox
IP of box
log in /root
PW dreambox

any tell me what im doing wrong

cheers guys

[jw2000uk]

@Donkey... just use dream-up mate, with the null cable... job done.. theres a backup.img in this thread u need.


Great image, BUT im getting one major problem..

If i boot up, go to a random channel, and then back to bbc1, its black, and so are 50%...

i reboot, then all back...

tried my own boquets and the same problem.. Shame.

[pogo2009]

Here is another UK Ready backup for dm500 Users, one or two reported problems with Oscam not starting first on the last backup so this is for you.

http://img716.imageshack.us/img716/8775/oie211859560spzf6pe.jpg (http://img716.imageshack.us/i/oie211859560spzf6pe.jpg/)

Loaded with SGTFlipFlop bouquets of 14/9/11

CCcam info installed

No need to enter your boxkey, Oscam will read it from your card


http://img6.imageshack.us/img6/2630/screenshot1rr.jpg (http://img6.imageshack.us/i/screenshot1rr.jpg/)

http://img23.imageshack.us/img23/5771/screenshot2kmw.jpg (http://img23.imageshack.us/i/screenshot2kmw.jpg/)


Oscam Web info is installed, to view & check your entitlements
In your web browser type


http://IpOfDrembox:8888/E.G 192.168.0.9

Username & password = admin

Click Readers

http://img713.imageshack.us/img713/7150/39423511.png (http://img713.imageshack.us/i/39423511.png/)

Then view entitlements

http://img138.imageshack.us/img138/4436/18455198.png (http://img138.imageshack.us/i/18455198.png/)

**********************This image is configured to update your entitlements automatically ************************


Install by Dreamup or Flashwizard pro, both formats attached below.
Use whichever you prefer.

Enjoy

Dreamup Version
(http://www.multiupload.com/RA26LXYKXT)
Flash Wizard Version (http://www.multiupload.com/8P8K39ZHWX)

[RockMonster]

Just playing around with DM500 images. successfully uploaded Nabilosat and Gemini. Tried this one and my box is now dead as a dodo!!!
Maybe its something I did, but lets be careful out there.

[Ureyesonly]

Just playing around with DM500 images. successfully uploaded Nabilosat and Gemini. Tried this one and my box is now dead as a dodo!!!
Maybe its something I did, but lets be careful out there.

Not sure wot you done wrong but this image works perfect, I'm usein it in DM500c

[juliusng]

Hi...


I need help on how to reset and flash my 500C. Now mine set is totally mesh up.

Thank alot...

[tony49]

ok lads can someone till me pls ive been told that cccam 2.13 will not auto update my card if that is the case y does all these images come with oscam and cccam 2.13 not 2.14

[cgscott]

Very apt for the 256 trick i think

[standarren]

i cant seem to get the epg working not sure why any one have it working ?

[kevhky]

Pogo2009

Installed and working spot on the gemini version, why is it though when i look at the servers in webinfo its showing as 1 connected and its newcamd, is this something you have put into the image as its none of the servers i have got with an ip address of 127.*.*.10001

Cheers

Kev

[visco]

Here is another UK Ready backup for dm500 Users, one or two reported problems with Oscam not starting first on the last backup so this is for you.

http://img716.imageshack.us/img716/8775/oie211859560spzf6pe.jpg (http://img716.imageshack.us/i/oie211859560spzf6pe.jpg/)

Loaded with SGTFlipFlop bouquets of 14/9/11

CCcam info installed

No need to enter your boxkey, Oscam will read it from your card


http://img6.imageshack.us/img6/2630/screenshot1rr.jpg (http://img6.imageshack.us/i/screenshot1rr.jpg/)

http://img23.imageshack.us/img23/5771/screenshot2kmw.jpg (http://img23.imageshack.us/i/screenshot2kmw.jpg/)


Oscam Web info is installed, to view & check your entitlements
In your web browser type


http://IpOfDrembox:8888/E.G 192.168.0.9

Username & password = admin

Click Readers

http://img713.imageshack.us/img713/7150/39423511.png (http://img713.imageshack.us/i/39423511.png/)

Then view entitlements

http://img138.imageshack.us/img138/4436/18455198.png (http://img138.imageshack.us/i/18455198.png/)

**********************This image is configured to update your entitlements automatically ************************


Install by Dreamup or Flashwizard pro, both formats attached below.
Use whichever you prefer.

Enjoy

Dreamup Version
(http://www.multiupload.com/RA26LXYKXT)
Flash Wizard Version (http://www.multiupload.com/8P8K39ZHWX)i have installed this back up on clone dm500s and workks great for me and family clines,but i went into cccam 2.13 confg server and clients and could not see entitlements info is there a reason or can i edit and put the entitlement info back. so i know when card willl need updating .thanks

[pogo2009]

Pogo2009

Installed and working spot on the gemini version, why is it though when i look at the servers in webinfo its showing as 1 connected and its newcamd, is this something you have put into the image as its none of the servers i have got with an ip address of 127.*.*.10001

Cheers

Kev
This is the nline connecting oscam & CCcam, the ipaddress is for local machine. Sorry for the late reply.



i have installed this back up on clone dm500s and workks great for me and family clines,but i went into cccam 2.13 confg server and clients and could not see entitlements info is there a reason or can i edit and put the entitlement info back. so i know when card willl need updating .thanks
You now have to view entitlements via oscam as shown in the post you quoted.CCcam no longer reads the card thats why you see no entitlements mate.

[sgerrard]

hi i have the openPLi-beta-dm500 image on my dreambox 500s clone.

is this the same image as the one becing discussed in this thread?

i have been through some of the menu, and kept it at most of the default settings (changed the time zone etc)

now its asking me "no diseqc" "simple" or "complex"

im not sure what i should choose now? i have a 1 metre motorised dish

anybody help please?

thanks

[fay28]

"Oscam Web info is installed, to view & check your entitlements
In your web browser type


Code: Check this link
http://IpOfDrembox:8888/
E.G 192.168.0.9

Username & password = admin

Click Readers"


hi guys image uploaded fine but cant get to the above, entered my box ip but cant get webinfo. can anyone help please?

[visco]

"Oscam Web info is installed, to view & check your entitlements
In your web browser type


Code: Check this link
http://IpOfDrembox:8888/
E.G 192.168.0.9

Username & password = admin

Click Readers"


hi guys image uploaded fine but cant get to the above, entered my box ip but cant get webinfo. can anyone help please?This is what you need to type.
for example..http://192.168.0.9:8888/
it worked for me,please note you must use the ip of your recieve.r

[fay28]

This is what you need to type.
for example..http://192.168.0.9:8888/
it worked for me,please note you must use the ip of your recieve.r

my box ip is 10.x.x.x and it does not work with

http://10.x.x.x:8888/

[azzakidiwala]

Hi i really want this image but cannot connect remotely few problems :/ is it possible i can get a copy of a .img?

Thanks Azza

[azzakidiwala]

I flash mine with the file from OpenPli's website. and when i tried to do this with a remote access it patches through and does everything on the computer but nothing happens to the box :S? Can someone help. Thanks

[azzakidiwala]

New problem
ok updated firmware on dm500 with the backup.img copy (Thanks for that btw) all up and running with DreamUP.
OK plug it in ethernet port and stuff. But non of the channels work? SO CONFUSED :'(

Someone please help me! Newbie and want to get my head around this!

Thanks Azza :)

[fay28]

my box ip is 10.x.x.x and it does not work with

http://10.x.x.x:8888/

im still stuck on this folks can anyone help?

[azzakidiwala]

@fay28 (http://www.digital-kaos.co.uk/forums/members/28219-fay28/) what i did is input my ip address and press enter.

Http://192.168.0.0:8888/

Just put that in the address bar simple!
so you see my ip address is 192.168.0.0

(Dont worry not my actual ip ;))

[fay28]

tried that

i get


Internet Explorer cannot display the webpage

[rricky]

Hi guys been using this image for a few months and everything 100 %. Now when i remove a few users from oscam.user they still seem to show in the web info as user not found or user disconnected.

Any help as to what i am doing wrong.


Thanks in advance

[rricky]

Any help guys about users removed showing in web info as anonymous disconnected from ip addy or the persons username not found.

I thought when you remove a user they shouldn't be able to try and connect.

[DigitalDaz]

I flashed this image, really liked the look of it but as someone else posted above, I could hardly receive any channels. Even a scan picked up very few.

I'm using a genuine DM500S

[garry1312]

Any help guys about users removed showing in web info as anonymous disconnected from ip addy or the persons username not found.

I thought when you remove a user they shouldn't be able to try and connect.

Although they can no longer access your card while the line is still in there receiver it will try and connect to the server. This still causes unwanted traffic but they cannot view your card.

Advice them to remove the line from there receiver.

[maclaren786]

are the pli images are faster than nabilo sat and stable?????

[garry1312]

are the pli images are faster than nabilo sat and stable?????

Not sure mate but when I used a 500s I found that Pli images were extremely stable, better epg support and never had any issues with speed.

[satshop77]

hi is there something im missing here? i have flashed the box as i have a hundred time and installed the cccam. inserted the card and its not recognised by the internal reader. what am i missing?
what should i be looking for?

thanks

[cmfable]

Install by Dreamup or Flashwizard pro, both formats attached below.

Use whichever you prefer.

Enjoy

Dreamup Version
(http://www.multiupload.com/RA26LXYKXT)
Flash Wizard Version (http://www.multiupload.com/8P8K39ZHWX)

Pogo Dreamup Version, all links are dead or removed... can you please upload?

[AfyB]

Am i right in saying if you currently have cccam installed, you can upload this soft cam on this thread and it wont affect your cfg file? Is it just a matter of uploading this file??? I have had a disconnecting issue of clients on only cccam, will this file of oscam and cccam possibly solve my problem? Is it worth switching?

[garry1312]

theres no need to use cccam and oscam together. Oscam as reader and server works very well and you are still able to issue C lines by using CCcam protocol or whatever line using other protocols.

Personally I would use Oscam on its own.

[AfyB]

Sounds good, but as certain "people" already have clines, maybe it's better for me to use Oscam with CCcam? I don't mind just using Oscam, but i don't know where to start with setting that up?

[garry1312]

Got your PM earlier mate will send you a PM over the weekend and explain a bit more :)

[AfyB]

Top man. Decided to buy a Dm800HD pro today, but i'll try the Oscam route hopefully that will solve my problem.

[madmanuk]

yo lads where do i put my flins in this image. do i just download cccam config like before.
thanks

[smoggie]

cfg file goes to var/etc. If there isnt one in image then back up the one on your current image and transfer it over. failing that you can create your own using note pad naming it CCcam.cfg

[madmanuk]

thanks mate so its just like using cccam,Also where do i put my port for them to connect to my box or do i put all the config in with port and bk and what ever els is in there.
thanks pal

[fay28]

tried and tested, caused frezzing issues among users

[madmanuk]

the links dead lads

[madmanuk]

Yo lads got this another one from somewhere els and it looks like its working i now get pick tv and without bk,just got to see how its gets on now thanks for your help lads,Just 1 more thing does anyone know how to get this setup on my dm600 pvr.
thanks

[madmanuk]

yo lads how can i get this working with cardshare studio so i can see the channels my mates are on and card updates.
thanks/Sorted who's online but i car't see what channel there on and my card updates.help

[smoggie]

get the latest channelinfo and cccam.provider files and put them in var etc.
For entitlements put http://192.168.#.#:8888/ in to web bowser and login in.Click on Reader and on next page to the right is Action, under here is what looks like a piece of paper with a key on it. Click on this and you will get your entitlements.

192.168.#.# server ip

[madmanuk]

thanks mate i can now see the entitlements,Now where can i find channel info and cccam provider files mate.
thanks

[smoggie]

google is your friend for that

[madmanuk]

ok mate thanks

[SGTFlipFlop]

thanks mate i can now see the entitlements,Now where can i find channel info and cccam provider files mate.
thanks

http://www.digital-kaos.co.uk/forums/f216/sgtflipflop-skyuk-bouquets-updated-regularly-163750/index32.html#post1464205

Channel.info here

[madmanuk]

cheers mate

[madmanuk]

all working now mate thanks

[Fano]

theres no need to use cccam and oscam together. Oscam as reader and server works very well and you are still able to issue C lines by using CCcam protocol or whatever line using other protocols.

Personally I would use Oscam on its own.

Can you issue both C and N lines using this setup ?

[Shady]

can you read the rules about c/s talk on dk?

[madmanuk]

who i didn't know i did anything wrong if your on about me sorry

[satsmo]

I don't think shady meant you.

[madmanuk]

thats good then mate thanks

[mrmaskin]

can i flash this using dreamup or do i have to use flashwizard. i find flashwizard confusing and hard to use.

im a newbie

[madmanuk]

its easy with flash wizard mate

[iGame]

So does this include everything such as the epg, and channels. I am a newbie.

So all I would have to do is put my cline and fline in then it should work, and what is a fline

I will try this on my clone box when it arrives

Thanks

[seanmckeown]

the easiest way of all is probably to telnet.

1. unzip image and FTP it in var/tmp (rename it backup.img)
2. Open 'Run' in windows, type 'cmd', press ok
3. type this: telnet 192.168.xx (the IP of ur box)
4. login as root/dreambox
5. type this: cd /var/tmp (press enter)
6: type this: eraseall /dev/mtd/3 && cp backup.img /dev/mtd/3 (press enter)
7: type this: reboot (press enter)

then it reboots with the new image

[hollander95]

can we have a screenschot please?thanks

[n0chex]

The links are dead to the image file and flash wizard anyone got a working link for both please.

[n0chex]

Anyone help me wih a valid link for the above files please.

[mtv1]

can you read the rules about c/s talk on dk?

wtf is cs :hmmmm2:

oscam on its own is ok when you have peers you can trust i would recommend cccam as a rule :D

also that new burger in burger king is the dogs { literally }

[AfyB]

How do you set up oscam to run as reader and cccam as processor?

[bigup]

anyone still using image hows it been? stable?

[sloshed]

will this work on a dm500s clone

[cgscott]

will this work on a dm500s clone

Yes pli images are fine. As are most images now anyway.

[pauliebb]

Hey guys im new to dreambox but loving it.

flashed a few images but not really suiting me a uk user.

wanted to try this but links are gone? anyone can help?

thanks for fantastic forum!

[gji25]

file does not exist from the link.. any other link available ?

[psats]

file does not exist from the link.. any other link available ?

more links posted on other pages.

http://www.digital-kaos.co.uk/forums/f214/open-pli-oscam-cccam-uk-ready-epg-mapped-backup-225268/index3.html#post1268807

[gji25]

This file does not exist, the access to the following file is limited or it has been removed due to infringement of copyright.
any ideas ?

[mtv1]

https://rapidshare.com/files/2889307361/pli_uk_backup.rar enjoy :)

[southpaw]

wonder if somebody can advise me , downloaded the gemini image and changed a few settings (test1 test2 user/pwd) and entered my f-lines to the ccca# config , however osca# doesnt seem to let ccca# connect , giving the following log

c user southpaw is trying to connect but doesnt exist ! (CCcam)
2012/07/03 12:39:26 c plain newcamd-client 127.0.0.1 rejected (no such user)
2012/07/03 12:39:26 c thread 32025B50 ended!
2012/07/03 12:39:37 c client connected to 10001 port


can anybody advise were i have gone wrong please, obviously somethin bloody obvious but nothin i can see

mtia

[mtv1]

did you add user and reader to oscam ?? :afraid: ask upstairs lol

[southpaw]

thanks for reply mtv , yeh all the configs were pre-installed in the gemini image on page3 , just tweaked the user/pwd
from test1/test2 to my own, obviously changed these in the n-lin# in ccca#cfg also but it dont seem to allow ccca# to connect , read somethin from davvo bout the "script path" last post in this thread
http://www.digital-kaos.co.uk/forums/f39/oscam-ccam-debian-linux-209949/
but would have thought everythin was pre-configged on this image as the title suggest`s ???

[owengrey]

wonder if somebody can advise me , downloaded the gemini image and changed a few settings (test1 test2 user/pwd) and entered my f-lines to the ccca# config , however osca# doesnt seem to let ccca# connect , giving the following log

c user southpaw is trying to connect but doesnt exist ! (CCcam)
2012/07/03 12:39:26 c plain newcamd-client 127.0.0.1 rejected (no such user)
2012/07/03 12:39:26 c thread 32025B50 ended!
2012/07/03 12:39:37 c client connected to 10001 port


can anybody advise were i have gone wrong please, obviously somethin bloody obvious but nothin i can see

mtia
Same as above is trying to tell you!

Have you added the user to oscam config as server is saying client is trying to logon but no such user..... hope that helps!

[madmanuk]

could do with one like this for the 600pvr lads

[stefanb]

Multiupload.com - upload your files to multiple file hosting sites! (http://www.multiupload.com/PWG39HTFC8)

flashwizard

Multiupload.com - upload your files to multiple file hosting sites! (http://www.multiupload.com/4KDM7QGXUX)[/QUOTE]

I could no download the files from there with out installing some crappy client that tried to fill my laptop of search engines and toolbars with out even downloading a byte, it is really disappointing that what seems to be good image is only posted but not downloadable unless spending hours fixing up after trying.

Id appreciate some different delivery method like attachment here in the forum as others do.

[gold7]

Hi good people . can not download this image from links provided can somebody please show me where i can download it from.

much appreciated

[the man]

any new working links?
any updated 0scam or oscam-cccam 2.1.3 500s images?

[visco]

i have back up rar what everyone needs if admin say its ok i will post it mates

[waj_uk]

Having a little problem got this image on my 500s and inserted card and only clearing basic channels not premium, internal card reader is working as it reads cards for the basic package any ideas i havet changed anything in the config files i assumed it was ready to go

[mdt]

Having a little problem got this image on my 500s and inserted card and only clearing basic channels not premium, internal card reader is working as it reads cards for the basic package any ideas i havet changed anything in the config files i assumed it was ready to go

enter box key,regards mdt

[housh]

where can i dwonload this

[piptaps]

The links provided dont work

[digicon]

They are well gone by now unless some kind sole still has all the software and re-uploads

[davemdavem]

Hi.

Hopefully someone can point out where I'm going wrong with this as i can usually resolve these sort of problems just by reading through many many comments but after 4 full exasperating days, i've decided to ask for assistance as i'm sure it's going to be very very simple to sort.

I'm trying to set up pogo2009's image (Open PLI 25/8/11) to use oscam as client on my dm500, with a dm800 being server.

The client dm500s has oscam 1.10 rc-svn build #5921 & CCcam 2.1.3. (assume this has an ip of 192.168.0.100)
The server dm800hd has oscam 5965 & CCcam 2.1.3. (assume this has an ip of 192.168.0.200).

Below are my client & server files.

Client oscam.user
[account]
user = client1
pwd = client1
disabled = 0
uniq = 1
group = 1
au = 1
caid = 0963:000000
monlevel = 0
host = 192.168.0.200


[account]
user = dvbapiau
pwd =
group = 1
au = 1

Client oscam.server
[reader]
label = skyuk
protocol = newcamd
device = 192.168.0.200,12000
user = client1
password = client1
services = 0963
group = 1
emmcache = 1,3,2
blockemm-unknown = 1
blockemm-u = 1
blockemm-s = 1
blockemm-g = 1
cccversion = 2.1.3
ccckeepalive = 1
audisabled = 1


[reader]
label = skyuk
protocol = camd35
device = 192.168.0.200,12000
user = client1
password = client1
group = 1

Client oscam.dvbapi
P: 0963:000000 # prioritise CAID 0963 with provider 000000

Client oscam.conf
[global]
logfile = /tmp/.oscam/oscam.log
nice = -1
serverip = 192.168.0.200


[monitor]
port = 16500
nocrypt = 127.0.0.1,192.168.0.1-192.168.0.255


[newcamd]
port = 10000@0963:000000;10001@0963:000000
key = 0102030405060708091011121314
allowed = 127.0.0.1,192.168.0.0-192.168.255.255
user = client1


[cccam]
port = 12000
reshare = 1
version = 2.1.3


[dvbapi]
enabled = 1
au = 1
boxtype = dreambox
user = client1


[webif]
httpport = 8888
httpuser = admin
httppwd = admin
httprefresh = 60
httpallowed = 192.168.0.1-192.168.0.254
httphideidleclients = 1

Server oscam.user
[account]
user = client1
pwd = client1
uniq = 1
monlevel = 1
caid = 0963
ident = 0963:000000
group = 1
au = 1
#
[account]
user = client2
pwd = client2
uniq = 1
monlevel = 1
caid = 0963
ident = 0963:000000
group = 1
au = 1
#
[account]
user = client3
pwd = client3
uniq = 1
monlevel = 1
caid = 0963
ident = 0963:000000
group = 1
au = 1

Server oscam.server
[reader]
label = skyuk
enable = 1
description = dm800
protocol = internal
device = /dev/sci0
detect = cd
boxid = xxxxxxxx
caid = 0963
ident = 0963:000000
group = 1
reconnecttimeout = 5
emmcache = 1,3,2
blockemm-u = 0
blockemm-s = 0
blockemm-g = 1
blockemm-unknown = 1
lb_weight = 100


#ecmcache = 1

Server oscam.dvbapi
(empty .. all lines commented out)

Server oscam.conf
[global]
nice = -1
logfile = /var/log/oscam.log
maxlogsize = 0
saveinithistory = 1 # save to /tmp/.oscam/reader<number>
WaitForCards = 1
PreferLocalCards = 1
cachedelay = 120
server = 192.168.0.200
#
[monitor]
port = 988
monlevel = 4
nocrypt = 127.0.0.1
#
[cccam]
port = 12000
reshare = 1
version = 2.1.3
#
[newcamd]
key = 0102030405060708091011121314
port = 17000@0963:000000
keepalive = 1
allowed = 127.0.0.1,192.168.0.1-192.168.255.255
user = client1
#
[webif]
httpport = 16000
httpuser = root
httppwd = xxxxxxxx
httprefresh = 5
httpallowed = 127.0.0.1,192.168.0.1-192.168.255.255
httpdyndns = xxxxxxxxxxxxxxxxxxxxxxxxxxxxx
#
[dvbapi]
enabled = 1
user = dvbpiau
au = 1
boxtype = dreambox
#
[cs357x]
port=12000

Regards,

Dave

[psats]

pli oscc backup.img

[digicon]

Hi Psats,


Do not post images with keys or roms included this rule also includes Cams


I am sorry but the forum will not allow any images that include Cams in the image to be uploaded, If you want to upload to an external link such as one of the many file sharing sites then thats fine.



Thanks for understanding

[psats]

doohh forgot...

[davemdavem]

@psats

thanks for the attempt to help me. any chance you can save my sanity, and my wife's sarcasm, and post the oscam files? i'm sure it's only a couple of settings i have wrong but i just cannot see what is wrong.

thanks,

dave.

[r11co]

Anyone got a link to an upload of this ;) ;) ;).

Many thanks.

[PaphosAL]

Just wondering, but why do peeps need oscam AND cccam resident at the same time, when oscam has its own built-in cam so can do everything? You just tell it to use cccam protocol

Cheers- AL :)

[digicon]

Just wondering, but why do peeps need oscam AND cccam resident at the same time, when oscam has its own built-in cam so can do everything? You just tell it to use cccam protocol

Cheers- AL :)


Basically Al without stepping on the rules too much but having the them both connected there are more options available on the C side for control than there is on the O side


Regards

[PaphosAL]

OIC, ta. But when I was configuring o**am recently, Mr Google found me a sample vanilla o**am.conf file that read like 'War and Peace' in terms of available options, LOL!

Cheers- AL ;)

[lfc84]

deleted - posted in wrong thread

[z11]

Guys,
Was looking to try the Pli image on one of my old boxes - all the downlinks seem to be broken on this thread .