PDA

View Full Version : Audi A4 2006


DiagService
1st October, 2011, 09:47 PM
I need Help
Audi A4 2006 2.0 TDI
I will change KM in DASH what is the best solution for change KM, I have vag K+Can 3.0 , UPA, x-prog .....

Thank
ledojo
1st October, 2011, 11:36 PM
Most appear to be microwire eeprom. Would depend on the cluster and clips you have for which tool.... Me, if no clear test points, I'd just remove ic and use uusp....
DiagService
2nd October, 2011, 01:21 PM
Most appear to be microwire eeprom. Would depend on the cluster and clips you have for which tool.... Me, if no clear test points, I'd just remove ic and use uusp....


I think that this should be done through the OBD ???
cokolo
2nd October, 2011, 03:54 PM
I think that this should be done through the OBD ???

OBD - Dp3 , Enigma , Avdi , Dashcoder , ..........:itsme:
sepistar
2nd October, 2011, 04:27 PM
if it is before 06.2006 you can also use tacho universal.
best regards
cokolo
2nd October, 2011, 04:57 PM
TU can correct Audi A6 before 06.2006 but A4 RB8 dash (-06.2006)on OBD , NO ??? Eeprom clip maybe .
dealerdon
2nd October, 2011, 06:40 PM
And what about vag dash can 5.17???
DiagService
2nd October, 2011, 06:55 PM
OBD - Dp3 , Enigma , Avdi , Dashcoder , ..........:itsme:


Is CARPROG good for mileage corection ????
cokolo
2nd October, 2011, 07:13 PM
Is CARPROG good for mileage corection ????

Nothing special :embarassed: in my experience is better for air bag :burnout:
sepistar
2nd October, 2011, 09:17 PM
TU can correct Audi A6 before 06.2006 but A4 RB8 dash (-06.2006)on OBD , NO ??? Eeprom clip maybe .
nope,because the algo what TU use,are in my opinion not corect and that ends with f....ed dash.
best regards
sepistar
2nd October, 2011, 09:27 PM
And what about vag dash can 5.17???

vag dash can can do it but only ecu.no dash!
best regards
cqae
3rd October, 2011, 04:29 AM
carprog wil work on some, its worth a go if you already have one, I've done a few VAG cars recently
autofan1965
3rd October, 2011, 08:17 AM
vagdashcan work with RB8 dashes. MDC too.
honingkoning
3rd October, 2011, 11:04 AM
vagdashcan work with RB8 dashes. MDC too.

dont use vagdash can it will end up with screwed dash
remove dash, remove eep, post dump or use licznick or other prog to calculate ans job done

Regards Honingkoning
d2mike
3rd October, 2011, 03:32 PM
vagdashcan work with RB8 dashes. MDC too.
That's right.
VagDashCan can do RB8.

... please use version 5.05. 5.17 is too bugy.
dealerdon
3rd October, 2011, 07:16 PM
That's right.
VagDashCan can do RB8.

... please use version 5.05. 5.17 is too bugy.

Can I use my orange vag dash k+can interface with 5.05 sw?
Anybody can send me a good version or give me a link?

thnx...
d2mike
3rd October, 2011, 07:26 PM
I don't know if there exists a 5.05 version with the orange interface box. My VagDashCan 5.05 is black ;)