View Full Version : Cummins INLINE 5 INSITE 7.5 setup
autodiagnostic
12th October, 2011, 07:02 AM
Cummins INLINE 5 is not easy to use especially for the beginers, I find one
(http://www.uobd2.com/upload/pro/cummins-inline5-v7.3-diagnosis-software-setup-instruction.pdf)
dimitar22
29th December, 2011, 10:24 AM
95601I have one question i need pinout from the inline 5 interface so i can use it with vcads pro.
I found this pinout on the forum, but in order to make one a need to know what the eight pins on the volvo connector are which is GND which is VIN and so on, and which pins correspond on the inline 5 adapter.
dimitar22
29th December, 2011, 01:05 PM
I found that
Pin 23 is 24V-
25 is 24V+
6 is J1939+
8 is J1939-
4 is J1708/1587 LO
3 is J1708/J1758 HI
This is on the inline 5 interface.
But now i don't know if J1708 LO is J1708 plus or minus ?
And can some one please confirm that the pinout on the picture above for the volvo 8 pin is correct?
pbateman
2nd January, 2012, 02:33 AM
Hey fellow DK friends don't know if anyone has seen them or not yet but Cummins has released a new inline 6 thought the information would be helpful to those who are using inline adapters.
http://inline.cummins.com/downloads/I6DriverSetup32.zip
http://inline.cummins.com/downloads/I6DriverSetup64.zip
http://inline.cummins.com/onlinemanuals/ServiceInstructions6.pdf
:party:
mozzie
2nd January, 2012, 11:27 AM
Hey fellow DK friends don't know if anyone has seen them or not yet but Cummins has released a new inline 6
Yes i suppose they had to do something
the inline 5 was a dud.
Check out the Dec2011 newsletter;
-says inline 6 has support for J2534 also.
https://insite.cummins.com/insite/info/index.html
renesis
3rd January, 2012, 11:56 AM
why is the Inline 5 a dud?
I have been using it for the past 4 years and all is well... except I cannot get Wabco Toolbox/Volvo Vcads to work through it.
mozzie
3rd January, 2012, 12:09 PM
why is the Inline 5 a dud?
I have been using it for the past 4 years and all is well... except I cannot get Wabco Toolbox/Volvo Vcads to work through it.
Many of them just stopped working;
was unpredictable when sometimes
less than a year sometimes after yrs.
kitty-hawk
3rd January, 2012, 09:22 PM
Dimitar,
Pinout volvo connector for DPA4+ or nexiq USB.
renesis
4th January, 2012, 04:16 AM
Many of them just stopped working;
was unpredictable when sometimes
less than a year sometimes after yrs.
thanks for your warning.. means I should be getting a replacement set for standby...
will inline6 work with older insite 7.4?
jctech
4th January, 2012, 03:47 PM
thanks for your warning.. means I should be getting a replacement set for standby...
will inline6 work with older insite 7.4?
Inline 6 works with Insite 7.5 and later, Inline 6 is supposed to support all Cummins Electronic engines.
service tool instruction attached
Roy Suryadwiananda
20th July, 2012, 07:43 AM
Inline 6 works with Insite 7.5 and later, Inline 6 is supposed to support all Cummins Electronic engines.
service tool instruction attached
Friends, if you have a Cummins Cummins adapter firmware 5.6.4.3 for Inline 5, beg to be shared here, thank you.
yogosutirto
20th July, 2012, 03:44 PM
Friends, if you have a Cummins Cummins adapter firmware 5.6.4.3 for Inline 5, beg to be shared here, thank you.
Take here . . .
http://www.digital-kaos.co.uk/forums/attachments/f166/133047d1342770484-dddl-6-4-inline-5-usb-inline-5.rar
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.