montero 02 ecu replacement

[placido]

hi friends, i need your expert advise, i repleace a used pcm on this montero, i want to see if someone could help me to virginize the ecu, i see a 5223970 eprom, can you give advice on how to read this one i aassume this is where the imo info is stored but i have no idea how to read eprom, wich option 93c66 or which one your help is always apreciated thanks in advance

[ray-ray]

Can you pull the immo. Off the donor car,located behind the radio? If not can you post a picture of the pcm?

[placido]

no donor vehicle, but here is the pictures
http://img844.imageshack.us/img844/4585/imag0339z.jpg




http://img819.imageshack.us/img819/711/imag0340z.jpg




http://img215.imageshack.us/img215/7070/imag0341o.jpgthis is what i call the back side if pictures are not that good let me know i will take better ones thanks

[sogaro]

Don't bother yourself with eeprom matters, get a tcode and simply program the ecu.

[placido]

where do i get a card sogaro? and the software to marry the coputer? i looked on ebay there is nothing can you give me a hint? thanks

[placido]

Ups my bad, a tcode has this option? i doubt it

[Zohar]

If you have a programmer for renesas MH83xx series, just read MCU`s flash and put dumps of ecu (512kb) and immo here. I will try to help you with matching immo+ECU.

BR

[sogaro]

Changing ECU in Montero is same as programming key to the car, i have done it at least 3 times. You don't need any card , when you need pin, tcode provides it for you so you just go ahead and do it.

[placido]

i tried to program keys to it,it didnt work i have tcode and it bypasses any pin code.

[placido]

i have upa, omega, and willem do any of this work? thanks

[sogaro]

There is a light that should show on the dash , can't really remember what sign it is again but its controlled by a relay on the front right side of the passenger seat. If its off or bad, programming won't take place

[Zohar]

I do not know about solution like `Sogaro` says, with keys rewriting. In this cause i am writing synchro bytes manually in dumps of ECU and IMMO.
Only MMCFlasher (??????? ??????? (http://www.mmcflash.ru/catalog/)), Piasini flasher and Ecuflash software (??????? ??????? (http://www.mmcflash.ru/catalog/)) may read this ECUs types.
Use OPENPORT 2.0 (cost above 180 USD - this is best tool for Mitsubishi, Mazda and Subaru chiptuning and ECU`s rewrite) with Ecuflash software for easy read/write this ECU via K-Line. Dump size is 512KB. Flashing method: EVO9

BR

[placido]

Can you post a link as where to buy this flashers

[Zohar]

Tactrix OpenPort 2.0 official site - Tactrix (http://www.tactrix.com/)
MMCflasher software official site - ??????? (http://mmcflash.ru/) , http://mmcflash.ru/forum/index.php?showforum=9?
Piasini flasher official site - Home: Piasini Engineering (http://www.piasiniengineering.com/)
Ecuflash software available on Tactrix site in download section (look at link in my previous post)
Only MMCFlasher can do some specific Mitsubishi ECUs (Lancer X 1.5 and etc). This software is also support reflashing of Mazda (all ECUs with MCU renesas SH70xx) and Ford (Visteon, SIM28) vehicles and this fllasher works perfect via OBD.

[Zohar]

For your education: full dump of ECU from Mitsubishi Pajero 3.0 AT MY2003 with MCU MH8301F.

BR

[placido]

i ordered the tectrix, i tried to locate the immobox, i cant find it behind the radio anyidea where else it could be located?

[placido]

another question raised, would it be possible to just read the old computer, and write over the donor one? using the dump from the original

[lateef]

@sogaro it doesn't work when you are matching ecu. it easy to program key with tcode but doesn't work for ecu.

[lateef]

only mitsubishi tool work on that.

[placido]

which on is that my friend?