TOYOTA TUNDRA all keys lost

[KILL_THE_IMMO]

hi all
i have toyota tundra 2006 usa ,all keys are lost,
can i use sbb to reprogram new key after erasing immobilizer?

plz i need explication step by step what i should to do because its the first time that i do this kind of car and its far from me about 250KM

waiting ur detailled help and thanks in advance:call2:

[placido]

yes just reset to 30 min, cicle ign from off to on six times if only one master key is registered good luck

[ray-ray]

No immo. On 06 they started adding transponder in 08 with the new body style.

[placido]

ray-ray is correct after 07, here in the usa they started cominig out with transponders, before that they did not, i apoligize

[KILL_THE_IMMO]

when i reset immobilizer last time and sbb write me erasing immobilizer succes
i? sure that have immo

plz what can i do after that???

[placido]

you might have to flash immo or computer chip, to get the car to learn keys, it depends on what king of sistem you have, look behind dash to see if there is an imovilizer , read and post your eprom is usually a 93c56 let us know

[ray-ray]

I would look for the ariel first,no ariel no transponder. Next I will fine the ecu should have 4 plug in (non-transponder) if it has 5 plug in then open ecu and flash non-transponer file and unplug center small plug.

[KILL_THE_IMMO]

it have a ring in the ignition so it is with transponder

[KILL_THE_IMMO]

PLZ I NEED TO KNOW WHAT CAN I DO FOR IT STEP BY STEP
THIS IS THE FIRST TIME THAT I DO THIS CAR

[ray-ray]

What is the immo. Light doing with the key in the ignition and with it out? If light is solid then it is reset and waiting to see 4D chip ,3key needed.2master and a valet the valet will close the learn mode. you can add 1master and 1valet and close.

[placido]

either way you do it, you still have to read the eprom out of the immobilizer or the computer, wichever one the vehicle has, you must determined wich one it is, i would guess that you have the separate immo behind the cluster and if that was the case read the eprom load up your file and someone here will help you virginize it, so the car will be ready to learn keys, it will be the same way when you remove the computer if the key info is stored in the computer once you determined which sistem you have then everything else should be simple, after that you might have to syncronize the computer with the cluster, but determine your sistem then we move on to syncornize

[placido]

by the way the eprom you are looking for could be a 9xxxx

[KILL_THE_IMMO]

What is the immo. Light doing with the key in the ignition and with it out? If light is solid then it is reset and waiting to see 4D chip ,3key needed.2master and a valet the valet will close the learn mode. you can add 1master and 1valet and close.


yes it is blinking without key and fixx when the key in ignition

[KILL_THE_IMMO]

either way you do it, you still have to read the eprom out of the immobilizer or the computer, wichever one the vehicle has, you must determined wich one it is, i would guess that you have the separate immo behind the cluster and if that was the case read the eprom load up your file and someone here will help you virginize it, so the car will be ready to learn keys, it will be the same way when you remove the computer if the key info is stored in the computer once you determined which sistem you have then everything else should be simple, after that you might have to syncronize the computer with the cluster, but determine your sistem then we move on to syncornize


if the immobilizer is reset whit sbb reading eprom isnt necessary?????

[KILL_THE_IMMO]

whit zedbull i know how can i precode 4D to be 4D67 toyota master key but Valet key i dont know how can i do it

[koncimobil]

valet key / sub key code: 92, 93, 95, 97, 99

[placido]

do you already have a master key?

[ray-ray]

Reset has been done,and the 1key is in the system. Need to add a valet or cycle key 5X and step on the brake.

[KILL_THE_IMMO]

no i dont have a master key

[KILL_THE_IMMO]

Reset has been done,and the 1key is in the system. Need to add a valet or cycle key 5X and step on the brake.

idont understand my friend

[KILL_THE_IMMO]

can i do it directly with sbb (it is usa car) without reading and writing data key on dump???

[marginal]

Today I tried to program a key using a valet one on a 2010 Toyota Camry without success.
The system needs a master key to do that.
When I wanted to erase the immo info and start from scratch, it said it'll need a password.
Isn't it the same for this Toyota?

Regards.

[KILL_THE_IMMO]

no isnt the same ist an american toyta car i erased immobilizer with sbb (14 MIN) but after i dont know what can i do , ( i ld like to know and after doing)
i dont like (if possible ) reading dump and put data key into
i search a direct way

[ray-ray]

The immo. Has been reset with the SBB ,14min.correct no keys in the immo. Now you need to get 2master keys 4D-67 and 1valet key 4D-92 to end lean mode program. the immo. Light is your guide on all key programming issue. It is like a red flag telling you what is wrong. Light blinking with no key,(immo. Working)key in and turn to on and a solid light.(1 key and in learn mode)**You need to add your keys and end your program. Have you done a hard reset to the car battery? Un-Do the battery cable,+and- and rub them together.

[KILL_THE_IMMO]

Have you done a hard reset to the car battery? Un-Do the battery cable,+and- and rub them together.

can u explain plz ?
when immo is in key learn mode with 1 st key i should to put other keys (how many time for each one??)

thanks my friend

[KILL_THE_IMMO]

Have you done a hard reset to the car battery? Un-Do the battery cable,+and- and rub them together.

can u explain plz ?
when immo is in key learn mode with 1 st key i should to put other keys (how many time for each one??)

thanks my friend

[placido]

look whe you have reseted the immovilizer like you said with sbb you have a solid sec light on the dash? now the car is ready to learn keys, this is what you do if you need to program two keys,
put the first key in the ignition do not turn on
put the second key in the igntion do not turn on
put the firt one back in the ignition and cicle it real fast from off to on six times your sec light should desapear good luck my friend

[KILL_THE_IMMO]

I am grateful for ur help my friend

[placido]

it feels great to be helpfull

[KILL_THE_IMMO]

thanks for all
____________________resolved______________________