rover 200 coupe immo off

[jjas40]

hi
I need immo off for this car:
rover 200 coupe 1.8 year 1999.
ecu is MKC 103981.
I have eeprom 93c66 with dump changed to immo off.
my question?
the ecu has two connectors: 1 white 2 red.
pin in the ecu that I have to cut?.

alarm box is above the fuse box, the connector is gray but the colors do not correspond with the post published in DK.
someone knows that I have to make bridges to complete the job?
thanks

[jjas40]

hi
no one knows?

[rossoelab]

I gathered some info
I hope they are useful

[jjas40]

hi
not
the ecu have two plugs
is mkc103981

[jjas40]

my dump 93c66

[rossoelab]

the plug in the photo is not the ECU
the plug and the ECU under the dash driver side
(pin transponder unit)

[jjas40]

yes
but......I disconnect the alarm module and the car starts and stops in a second.
I check the dump in 93c66 immo off, and changed the original dump.
here the dump immo off

[rossoelab]

Your ECU MEMS NNN 3-93c66
ECU MKC install 93c46
tests and reports

[adam28]

Is it mems3?

If so thiis will work

[jjas40]

hi
thanks
I have tried this option but does not work the ecu is not equal.
immo file is recoded.
I have made the bridge in the alarm box but I do not know what cable should I cut into the ecu, the ecu has a black and a red plug

[ninja123]

I looks like your ECU may be a MEMS 2J, can you post a picture of ECU? and is it a VVC engine?

Some of the coupes were throw backs, late registered but older models, dont think its mems3 on this.

ninja

[jjas40]

hi
yes motor is vcc.
photos here

[rossoelab]

strange when I open the file as MKS software gives me error
and tells me that MKS is 93c46

[jjas40]

eprom is 93c66

[ninja123]

I will look for solution and reply..........................

[mcgywer]

Try this one

[jjas40]

this dump is same origen not immo off

[ninja123]

Its been a while since I done one of these, but I did think eep was a 93x46, but I may be wrong as I dont have one of these ecu's to hand.

try this:

[jjas40]

hi
thanks ninja123
but.... this dump is 93c66?

[ninja123]

As I said, its been a long time!!

Try and post results, regards ninja

[jjas40]

hi
the dump off is large I can not program eprom 93c66

[jjas40]

hi
does anyone have the solution?

[jjas40]

hi all
help please

[sss123456]

Now i have the same problem as well, seems like this one was unsolved.

Anyone has any idea on this ?

[rabie_m]

THIS IS YOUR SOLUTION CUTE PIN 17 IMMO PIN
PASS IN PM

[sss123456]

HI Rabie,

Hre is my original file, same ECU.

please help me immo off too.

And ECU has 2 plugs, Red and Black,

Which wire to cut ? red or black plug ?

Thanks !

[rabie_m]

HI Rabie,

Hre is my original file, same ECU.

please help me immo off too.

And ECU has 2 plugs, Red and Black,

Which wire to cut ? red or black plug ?

Thanks !

HER YOUR FILE CUTE PIN IMMO

[sss123456]

HI rabie_m,

I've tested your file and cut the pin, it does not work.

[ahmetusta61]

rover 820 mck103991 93c66 off

thanks problem solved :)

[androso80]

привет всем
помогите пожалуйста, immo off rover 200 1.8 MKC103981

[alecsander114]

here is immo off file .
password in pm.

aici ai fisierul si parola e in privat.