remote RF clio programming

[KILL_THE_IMMO]

hi all
i have a renault clio year 2000 that i want to program a remote with zedbull renault system1 remote programming
-dump 1 :is the original dump from uch start the car
-dump 6: created in step number 3 remote is ok but dont start
-dump 7: final dump created in step 6 remote is ok but dont start car

plzzzz can sameone give me what is wrong and if possible give me a good dump


thanks:giveup:

[KILL_THE_IMMO]

NO HELP!!!!

[KILL_THE_IMMO]

can anyone tell me what is wrong plzzzzzzzzzzz ishould to finish it tomorrow

[albertros]

Hi,
looks like no one else will help, or can't help.

I have genuine zedbull but not the renault extra function, so I will do my best.

I think the original chip in the key and the transponder you have added are fighting each other.

Have you removed the aerial in the key?

Can you also load the file in section 3 ( create remote adoption file )

[KILL_THE_IMMO]

i removed arial from the key
dump 6 is the same created remote adaption file creatd in section 3 and here remote work but light flashing

[albertros]

Hi,

I am guessing here .

The starting part of the dump is 10 - 05/06/07/08/09/0a then repeated on line 50 etc


So that part of the dump should be the same as the dump that starts the car?

[KILL_THE_IMMO]

SO I SHOULD REPLACE 03 F1 24 C8 80 12 (LINE 10 & 50 DUMP 7) BY CF 24 F1 80 C8 12 (WORKED DUMP)

[albertros]

Yes try it, I once played with Tmpro but didn't make notes

[KILL_THE_IMMO]

I M WAITING COSTUMER S CAR AND I WILL TELL U IF IT IS OK OR NOT

[KILL_THE_IMMO]

it is always remote working but no starting

[KILL_THE_IMMO]

pfffffffffffff zedbull always problem

[albertros]

Hi,
I need to get a life!

OK in the last dump ( 7 ) the code incription is reversed and it shouldn't be. = ( 24 F1 80 C8 ) has become ( F1 24 C8 80 )

So I suspect you have read it in 8 bit mode then in ordinary mode. ( I hope )

So replace ( F1 24 C8 80 ) with ( 24 F1 80 C8 ) in lines 10 and 50

Good luck

[damih]

Hello,your remote work in a last dump here a pin code and now program a key via diag by a PIN code and that's it

PIN for your last dump is 3917(7.bin)

[KILL_THE_IMMO]

but i should use a 33 chip to program it with diag tool and i dont have it i have T5

[albertros]

Hi,
can you post a copy of the dump in process 3, before you press the remote.

Thanks

[damih]

No use your original transponder

[KILL_THE_IMMO]

this is the created remote dump

[KILL_THE_IMMO]

i m not using the original transponder

[KILL_THE_IMMO]

Hello,your remote work in a last dump here a pin code and now program a key via diag by a PIN code and that's it

PIN for your last dump is 3917(7.bin)

programmig with diag or directly from the dump is the same

[albertros]

Hi,
Just my thoughts as I havn't tested.

If you program the transponder again using the new code the code in the ecu will still be wrong.


So try replacing the reveresed data as I suggested in my post #12

Observation :-

I think the problem is simply thet the dumps are being read in 8 bit and 16 bit mode mixed up.

You need to make sure that you use the same mode and check it particularly in section 3 Try attached

[damih]

Hello,sorry do you have a RF remote(radio fr?quence)
or IR(infrared)??
if you have a RF remote you have a transponder in same chip as a remote you need only learn a key using a device with a PIN code like that in your dump 7.bin
you write a transponder
Is note a same if you generate a transponder by dump
And job done
OR if you have a IR generate a transponder by dump(7.bin) and put it in the key

That's it

[KILL_THE_IMMO]

Hello,sorry do you have a RF remote(radio fr?quence)
or IR(infrared)??
if you have a RF remote you have a transponder in same chip as a remote you need only learn a key using a device with a PIN code like that in your dump 7.bin
you write a transponder
Is note a same if you generate a transponder by dump
And job done
OR if you have a IR generate a transponder by dump(7.bin) and put it in the key

That's it


sorry my friend u forgot that chip in the key of is one time programmable so i should modiy dump to accept it and progam a new chip for starting
thanks

[damih]

Sorry it's ID33 note one time programable

[KILL_THE_IMMO]

when i swap final dump to 16 BYTE fob work and light is continue without start

[KILL_THE_IMMO]

Hi,
Just my thoughts as I havn't tested.


I think the problem is simply thet the dumps are being read in 8 bit and 16 bit mode mixed up.



You need to make sure that you use the same mode and check it particularly in section 3 Try attached

with ur dump fob is ok but light flash slowly ( like without key in ignition) standby mode

[albertros]

Hi,
ok the rolling code has moved on one step so we need to re-set it.
2 options my be only one will work so try both ( unless the first one works )

Make a new transponder from the last dump I sent you - try it

0r

don't make a new transponder and load this dump ( 7 experi 3.rar ) into 93c46

the transponder logic ( just out of intrest )
30c0810307f0ff00 - 00e0000efc387000 changed to next one which is :-
30c0810307f0ff00 - 00e0000efc380000

Line 10 - 0A changed from 02 to 12 which seems to set the rolling code

[KILL_THE_IMMO]

Hi,
ok the rolling code has moved on one step so we need to re-set it.
2 options my be only one will work so try both ( unless the first one works )

Make a new transponder from the last dump I sent you - try it



I MADE THIS STEP AND LIGHT FLASHING SLOWLY

[KILL_THE_IMMO]

I WILL SEND U REPORT TOMORROW
THANKS

[albertros]

HI,
After you make a change try leaving the ignition on for 5 mins, it may help re-aline.

Also try using same dump in 8 bit then 16 bit mode.

[KILL_THE_IMMO]

not working!!!!!

[albertros]

Hi,
so let me understand.

Dump 1 the car will start ( and dump 1 still works )

The rest of the dumps the remote works but the car will not start?

[albertros]

Hi,
so dump 1 still works?

[KILL_THE_IMMO]

yes it work but the other flashing

[albertros]

Hi,
I have had all afternoon on this.
Used a perfect working car
tried to program a spare key

The car learned the remote but it would not work after I switched the ign on.

The original key remote would work all the time.

So start again and the same happens only work on the remote until I turn the ign on.

I don't know if this is because its own key is stored somewhere else in the UCH or because the key I am trying to program is faulty.

I could not get the car to start with an emalgamated dump.

I think you are going to need zedbul or their agent to sort this one.

Please update if they help.

The emalgimated dump still gives the same immo code but I havn't played with the transpober dump

[KILL_THE_IMMO]

thanks very much my friend i will send u tomorrow 4 other dump for other clio car (same genre)
may u can find relation between dump