PDA

View Full Version : BMW e36 EWS II. key sync.


VTS_Tibi
11th November, 2011, 11:54 AM
Hi Guys,

I have a problem with a 1995 BMW e36 316i Compact. It has EWS II.

Car does not start, and also it doesn't even crank. So immo is active.


INPA gives the following error code in the EWS:

http://i1115.photobucket.com/albums/k545/TestorVTS/inpacode.png



How can I pair this key with the EWS? (it is the original #1 key of the car)
liloM
11th November, 2011, 12:57 PM
upload dump ews.
VTS_Tibi
12th November, 2011, 08:31 AM
I've tried to read the MC68HC11EA9 with Xprog M. I've tried it on board and now desoldered and tried to read with the appropriate adapter.

I still get "device is silent" error.

Should I alter the oscillator settings?
bali motor
12th November, 2011, 08:40 AM
I've tried to read the MC68HC11EA9 with Xprog M. I've tried it on board and now desoldered and tried to read with the appropriate adapter.

I still get "device is silent" error.

Should I alter the oscillator settings?

what mask MCU?
VTS_Tibi
12th November, 2011, 05:49 PM
what mask MCU?

the mask is: 1D47J
bali motor
12th November, 2011, 06:27 PM
lift mcu to read. if your use XPROG
VTS_Tibi
12th November, 2011, 06:56 PM
lift mcu to read. if your use XPROG

it's now desoldered... but still the same!
bali motor
12th November, 2011, 07:01 PM
what SW and HW your EWS?
i will send you data
bali motor
12th November, 2011, 07:15 PM
this data for 1D47J
VTS_Tibi
12th November, 2011, 07:35 PM
Thanks Mate! It's HW01 SW01!

What should I do with your file ? As right now there's the original key in the car which doesn't start.

Is your file a virgine file for the EWS?
bali motor
12th November, 2011, 07:39 PM
no.... you need make new tranponder... and make sync with ecu...
VTS_Tibi
12th November, 2011, 07:48 PM
Okay. Preferably I'm looking for a solution to sync the existing key to the EWS, or restore the EWS to virgin state.


But I still can't read the bloody MCU out :( "Device is silent"




OR!!! It would be also great to make the immo off completely!!! DME is a Bosch 0 261 203 276.
bali motor
12th November, 2011, 08:11 PM
yeah.. you can use emulator ews
ecufix
13th November, 2011, 06:34 AM
Use this and bridge out starter circuit on ews plug
davorOS
13th November, 2011, 08:52 AM
you need to set oscillator to 5529600 mhz to read it with Xprog in HC11 adapter

regards
VTS_Tibi
13th November, 2011, 11:44 AM
you need to set oscillator to 5529600 mhz to read it with Xprog in HC11 adapter

regards

WOW! Thanks Mate! Managed to read it out! I think XProg would read it out onboard too, using the same oscillator setting and Rx cut!



I've attached the dump! Looking for a virgin dump from this, so I could sync the existing key, and then sync the EWS to the DME.
bali motor
13th November, 2011, 12:29 PM
this dump ready to start
VTS_Tibi
13th November, 2011, 05:44 PM
this dump ready to start

Car started for the first time! Thank you very much! :D