XPROG-m - Schematic diagram and documentation

[Holtek]

Documentation for the XPROG-m programmer. :party: :proud:

Attachment contains:
- schematic diagram of the XPROG-m programmer, color and gray version,
- datasheets for all semiconductors,
- high-quality photos both sides of the PCB,
- XPROG-BOX to XPROG-m downgrade instruction,
- ATmega64 firmware,
- transparent instruction set fusebits

Thank you Elchip for your help - finding errors.



If anyone finds the any mistake in the diagram, please, send my a message. I make corrections and update the attachment. :D



BTW: If anyone have ATtiny25/45 dump to UPA USB programmer, please send me PM.
Best regards

If my post help, please Press http://www.digital-kaos.co.uk/forums/images/styles/digital/buttons/post_thanks.gifor Add Rep:wink:
http://www.digital-kaos.co.uk/forums/f154/images/download.gif

[wyz1056]

thanks!
have you atmega64 dump?

[Mracni]

If update clone 5.0 to 5.3.5 like Holtek say can be solved problem "Verify device" ??

[agabna]

hello
if u update to 5.3 u have to pay no way to go back
nooooo way

[dimitar]

hello
if u update to 5.3 u have to pay no way to go back
nooooo way

There is a way

[dimitar]

Solution in post #1

[Mracni]

can someone upload 5.3.5 soft?? I want update my clone

[Holtek]

If update clone 5.0 to 5.3.5 like Holtek say can be solved problem "Verify device" ??

Downgrade from version 5.3 to version 5.0 does not solve the problem of verification. Completely solved this problem in version 5.3 after registration and payment.

[Mracni]

Thank you for info Holtek,If this solution does not fix verify error I do not see any reason for update xprog-m

[mehran]

Thank you for info Holtek.
plese upload file ATmega64
thanks

[aetpos]

What method can be used to produce acurate double sided pcb's?
Photo/UV maybe?
As far as I can remember Photoshop can be used to create a PCB template starting from a picture of original board.
Also where is the Atmega dump??

[ta2lt]

please send me atmega dump
thnx

[galiza]

xprog-m repair (http://mhhauto.com/Thread-xprog-m-repair--3637)

[jldmasceno]

thanks for your information Holtek :top:
you could send me the dump ispmach 4064v ?
thankyou

[pacomasi]

hello need to dump atmega64 the all authorizations
if you could also post the version xprog-box 5.3.5 when unzip tells me this corrupt
thank you

[doslamer]

I'm looking for solution to downgrade from 5.0 to 4.5 .Any info will be very helpful.

[Anmed]

Need a dump LC4064V.
Thanks in advance!

[nm321]

Does this (attached) version can read the locked MCU MC68HC05B16?

[hoochyates]

what is xprog?

[dimitar]

Does this (attached) version can read the locked MCU MC68HC05B16?

Why dont you buy it and tell us if it can?

[dimitar]

what is xprog?
A chinese clone of a dysfunctional laundry machine.

[Holtek]

Many people ask me this question:
"How do I program XPROG-m, another programmer XPROG-m".

Below is a solution.

[miki18]

Is there any way to program atmega64 (still in circuit) troug PCs paralell port (with some resistors) like you can program atmega16 with AVR software?

[ficho]

Hi, I would like to use xprog-m as a k-line interface, how to set baud to 9600 8n1 ,how to Send Data and how to read Received Data.TimeOuts, multiplier's should be set to uart I suppose etc.
I know that it is simple to build K-line interface but why not use somthing that I already have.
I analyzed the protocol a little bit, but not everything is clear enough.

Regards Ficho

[georgegt]

A good dump for atmega64 vers 5.0 ?
can anybody help ?
many thanks

[napel]

Does anybody have the config file for programming atmega of xprog with another xprog? I only got flash and eeprom

[Holtek]

Config: FC FF CA 2F

[Komissar13]

How i can download ? i don't have permission..
A Need good dump for atmega64 and LC4064V, vers 5.0 ?
can anybody help ?
Thanks in advance!

[MrWho]

Hi Guys,


Can I use UPA USB to reprogram Atmega64 in Xprog-M thx ?

[bajticzek]

Way better than classic xprog, thanks!

[mrmarkus]

I buy the xprog-m clone, just one read, was all new, and sey Update firmware?... and now a nice metal box

[judor]

china clone ?

[vanos batam]

Config: FC FF CA 2F

hello Holtek
pls check this thread.. http://www.digital-kaos.co.uk/forums/f172/xprogbox-v5-4-3-flash-eeprom-292723/

maybe you can solved?
thankyou

[viercha]

Maybe somebody has Xprog-M PCB in PDF or any other format? Please share

Thanks in advance

[Holtek]

hello Holtek
pls check this thread.. http://www.digital-kaos.co.uk/forums/f172/xprogbox-v5-4-3-flash-eeprom-292723/

maybe you can solved?
thankyou

vanos batam (http://www.digital-kaos.co.uk/forums/members/189856-vanos-batam/) - I downloaded your ATmega64 dump. On my hard drive I have many dumps, different versions of the XPROG. I compared Your dump, and I'msure that this is not a dump for XPROG-BOX 5.4.3. This is not a dump for any version of XPROG-BOX.
It is the XPROG-m 4.5 dump!
If you set fuse follow my manual, this dump works correctly with XPROG-m version 4.5 and after updating the firmware works correctly with XPROG-m version 5.0.

[AudiS4]

Has anyone used the files to make a pcb or has a file of the pcb thats ready to be printed??

[fofo93]

upload 5.3.5 soft

[demos70]

Config: FC FF CA 2F


Ok I loaded cfg.bin and EEPROM.bin, when I first 'read' atmel it gave me that my original configuration was FF FF CA 2F

Now when I try to write, it changed config file to FC FF CA 2F, but it wrote a totally different EEPROM file than the one I loaded ....
I erased EEPROM and wrote again same EEPROM file, and when I read EEPROM it still gives weird eeprom file.

Eeprom file attached.

[jason1000]

hi all am looking at these programmer for my own use now theres a lot of intresting stuff on here about these devices i ve just purchased a upa programmer and going to do some experiment with peugeot bsi s so may need some help from you guys in the near future kep up the good work and this fourum is the best one for help and knowledge

best reguards to you all jason

[tawaf11]

good solution with x-prog m 5.3 to 5.0
thanks

[Holtek]

Many people ask me how to program the ATMEGA64 in XPROG with UPA-USB. Below is a picture that will explain everything.

[Holtek]

Finally, I publish the final version of XPROG schematic diagram rev. B. Fixed some bugs and added marking elements, as well as on the original PCB to XPROG-BOX from ELDB.

[panos2]

" access violation at address 00405394 in module XprogDesktop.exe . read of address 000003FC " this message keep getting when I go to read a file. There is a solution;

[alle bmw]

ok ok change pour

[mbsupport]

I have chine clone and when I try to read 9s12 or 1d69j, first time when I read receive "Verify error", but when I click second time the button "Read", then I read correctly the mcu. How I can fix this problem? When I reading FLASH of 9s12 and then I recieve "Verify error" can I damage the flash?

Thank you

[Tiberius]

Hello
anyone have a schematic for the xprog

[Tiberius]

hello
where can i get the schematic for the xprog?

[thayer201]

hello
where can i get the schematic for the xprog?

here you go....376802

orginally posted above Holtek (http://www.digital-kaos.co.uk/forums/member.php/121660-Holtek)


dont forget thanks.

[Signer]

i have Search ResultsXPROG-M Unknown command.Software error (https://www.google.com/url?sa=t&rct=j&q=&esrc=s&source=web&cd=11&cad=rja&uact=8&ved=0ahUKEwixi8vh1-XNAhVC1RQKHZPnAWo4ChAWCBswAA&url=http%3A%2F%2Fblogs.psychologies.com%2Fobd2expr ess%2Fdiagnostic-tool-17062%2Funknown-command-software-228744.html&usg=AFQjCNGIWWL2YnpRmDxuQM3fygk4lYh38Q&bvm=bv.126130881,d.d24)

[mikeg332]

I was hoping someone could help me out with some advice. I have recently received an xprog m box 5.6 clone. i have installed it multiple times. the device keeps saying "Device Silent" I have tried on multiple machines. Also the registration id reads "----------------" and no authorizations tab. How could i fix this and what do i need. Any information would be greatly appreciated

[maremuruk]

I was hoping someone could help me out with some advice. I have recently received an xprog m box 5.6 clone. i have installed it multiple times. the device keeps saying "Device Silent" I have tried on multiple machines. Also the registration id reads "----------------" and no authorizations tab. How could i fix this and what do i need. Any information would be greatly appreciated
Can be one of these :
1. USB Driver not correctly installed
2. Port is not correct, please click on Option ---> Environment ---> Ports ---> choose your correct Port
3. I heard Xprog 5.6 have many bugs, then your worst case is a faulty device
Good luck & best regards

[electronistul21]

is chinese clone with dongle ?

[mengu190]

Hi guys i have china clon xprog-m 5.55 it wont work only usb powered when i try to read any ic’s it makes buzzing noise and usp power shuts down, i use dc adapter and try to read then some eproms it reads but most of them it gives read error and box get hot
could anyone lead me where should i look for error, which ic could damaged ?
thanks

[goodbye]

which ver can work without usb dongle ?

[enigmaelectroni]

Thanks a Lot for this

[KrystianPoland]

Who has PCB for example in Eagle?