help with 2007 ford Fusion

[lwood]

i dont think i clear correctly. can some one clear crash dump for me.
2007 ford fusion
7E53-14B321-BE,
95160

i put the way i clear. but it didnt work.

[lawdog1]

i dont think i clear correctly. can some one clear crash dump for me.
2007 ford fusion
7E53-14B321-BE,
95160

i put the way i clear. but it didnt work.


Here you go

[lwood]

i am going to try it. will let you know

[lwood]

Here you go

Lawdog1, was the dump a tested solution.???
because i got DTC's
B1231 right seat or longitudnal acceleration , threshold exceeded
B2290 Occupant Classifications system fault

i try to calibrate seat. it would fail.
customer was upset so they left couldnt try anything else.

[lawdog1]

Lawdog1, was the dump a tested solution.???
because i got DTC's
B1231 right seat or longitudnal acceleration , threshold exceeded
B2290 Occupant Classifications system fault

i try to calibrate seat. it would fail.
customer was upset so they left couldnt try anything else.


Yes, I did two 7E53 this week like that ...

I have heard that Fords are known to store crash data in different locations, so the same solutions don't always work ...

[lwood]

Yes, I did two 7E53 this week like that ...

I have heard that Fords are known to store crash data in different locations, so the same solutions don't always work ...

really different locations.? wow.

[lawdog1]

really different locations.? wow.

Just a guess, but may be due to the direction(s) the car was hit, front, l-side, r-side, etc.

You can see in these posts it's not always cut and dry:

http://www.digital-kaos.co.uk/forums/f170/2007-ford-galaxy-crash-data-106228/ (read modulegod's post ... but I haven't been able to reset any 2006+ and most 2005 Ford with VCM/IDS so not sure he's entirely correct)
http://www.digital-kaos.co.uk/forums/f170/08-ford-focus-9s43-14b321-cc-ocs-code-wont-go-away-218610/
http://www.digital-kaos.co.uk/forums/f170/question-about-08-ford-focus-ocs-module-218201/

My clear worked for the 2 I did, but it could be that they were hit in the same direction. Also the guys have the real deal Ford IDS to calibrate the seat as opposed to an aftermarket scan tool (not sure if they even had to). Yours maybe was a side hit with crash stored in the OCS module itself? (see posts above) anyway, sorry it didn't work for you .... hate to hear that.

[ponchik]

vehicle had pass side impact, crash stored in pass seat railing, replace seat or railing.. good luck

[AMLGAR]

i dont think i clear correctly. can some one clear crash dump for me.
2007 ford fusion
7E53-14B321-BE,
95160

i put the way i clear. but it didnt work.


with your experience , you cleared V.I.N. in your clear dump ummmmmm interesting:hmmmm2:

[ponchik]

never clear vin and part #, you mistaken me with some one else, but if your tested file does not work with hard faults in o.p.d.s. this is the way to go, done hundreds of them.

[ubistvo]

to clear a ford airbag you must after dump clearin use a original ford diagnostic to reprogram ecu.
That is 100% tested i have that problem on 4 ford cars

[AMLGAR]

to clear a ford airbag you must after dump clearin use a original ford diagnostic to reprogram ecu.
That is 100% tested i have that problem on 4 ford cars

THATS CALL SETUP., before everybody thought after clear HONDAS u need SETUP(initialize) OPDS.. even me.. i a made some ford no SETUP, i think theres a way to do it with out SETUP

[ubistvo]

THATS CALL SETUP., before everybody thought after clear HONDAS u need SETUP(initialize) OPDS.. even me.. i a made some ford no SETUP, i think theres a way to do it with out SETUP

Can you tell as how ????

[rdu04]

can you help me clear crash data?
fomoco
6s6t 14b056 KA
5WK4 3586
eprom 95160

[SergeyIg]

Try it, it should work. Password PM

[rdu04]

Please wait password
says if there be scheduled after the write module EPROM or just give clear error
using minivcm

[SergeyIg]

Check out and give a clear error.

[leandroks]

285733
Hi there, could any1 help on clearing that dump???
Thanks in advance
Leo
It is a Ford Fusion 2008

[Aguilar3000]

to open this file, what i have to do???

[Johnner]

PM the original poster...they obviously have put a password on it for good reason :dontknow:

[lawdog1]

435872

Sorry I do not remember the password from all those years ago. Here's one I did that worked, you can see before and after. I'll PM you the Password



to open this file, what i have to do???

[Aguilar3000]

thanks for the information... but i have another dude... I unrar the file, but what program do you use to see the before or after????

[auto80]

thanks for the information... but i have another dude... I unrar the file, but what program do you use to see the before or after????

m8, you must use hexeditor to edit and compare files....

Cheers

[lawdog1]

Ultracompare from Ultraedit - that program will let you compare two files and see the difference


thanks for the information... but i have another dude... I unrar the file, but what program do you use to see the before or after????

[Newmotors]

hello friends can someone tell me if there is how to remove a dtc b2290 ford fusion?
hello friends can someone tell me if there is how to remove a dtc b2290 ford fusion?

[Newmotors]

hello friends can someone tell me if there is how to remover a dtc b2290 ford fusion 2007?

[ponchik]

hello friends can someone tell me if there is how to remover a dtc b2290 ford fusion 2007?

Try calibrating opds.

[Newmotors]

thanks for the return friend, already calibrated but i was not successful i tested the two occupancy sensors and one is without resistance was wondering if how to remove this dtc by the module ?

[ponchik]

thanks for the return friend, already calibrated but i was not successful i tested the two occupancy sensors and one is without resistance was wondering if how to remove this dtc by the module ?
Send me a part # for your module.

[Newmotors]

part number is 6553-14b321-bj

[Newmotors]

this is the file
this is the file