2010 enclave

[highrisk]

Does anyone know what chip is on this one?

[kimoe]

it should have a 6 Pin - 93C66

[hcip]

it should have a 6 Pin - 93C66

8 or 6 ? :manuflag:

[highrisk]

Tkank you. Does anyone have a picture of the chip location ? There are 3 ....8 pin and none are marked 93c66...i would be thankful for any help

[kimoe]

8 or 6 ? :manuflag:


Yes No Typo here , its a 6 PIN chip ,,, work on these in 2008 , very few autos used this back then, now i see them in the new Lincoln MKX-MKT :ridinghorse:

[kimoe]

Hers is the pic BTW, i try to read it on board back then = No Success

so best is to unsolder , so you don't lose any DATA.

[sunsation288]

Hello all , i have look for one , but just to be sure , when i look for the pintout of the NEC 703421 they not match , maybe i have not the right datasheet ? , anyone have the pinout of the eeprom ? wich pin is one ?
many thanks in advance

http://img.photobucket.com/albums/v235/25outlaw/aaa/P1190806avecnumros.jpg
http://img.photobucket.com/albums/v235/25outlaw/aaa/Pinoutupd703421.jpg

[digimile]

hi
u can read the 6 leg eeprom of 93c66X16 using upa programmer and adapters incircuit and need tachosoft calcualtor for calcualtion.In tachosoft calculation u need to swap bites else u get error in display.Need to coneect 6 wire around chip.all the board has thin glue on every component so need to clear the contact around chip.
thankx

[sunsation288]

hi
u can read the 6 leg eeprom of 93c66X16 using upa programmer and adapters incircuit and need tachosoft calcualtor for calcualtion.In tachosoft calculation u need to swap bites else u get error in display.Need to coneect 6 wire around chip.all the board has thin glue on every component so need to clear the contact around chip.
thankx
Many thanks digimile for your help , but i need to know where is pin 1 ? , and if my datasheet is good ...pin 92 and 93 of the lqfp is for LCD display ?
that made sense ?
thanks again

[CARPARTS]

Just look where is GND from those 6 pins.
That will be pin N? 5 from a regular 93c66...

[CARPARTS]

Vcc CS CLK
6 5 4
| |
) |
|________|
1 2 3
DO GND DI

So N?1 is pointed toward the NEC micro in your picture, because pen 2 is the GND.

[sunsation288]

thanks for the fast respond !! ... i don't want to upset you , but why with the datasheet of the micro they enter in port of the LCD ? please forgive me if you have done Enclave before and the method work for you i will follows your path if yes , but for me right now that don't made sense ?
http://img.photobucket.com/albums/v235/25outlaw/aaa/93AA66.jpg

[CARPARTS]

indeed, thats the correct image !
solder it out and make some adapter from the 6 pins to the 8 pins to read and write.

[CARPARTS]

The data out goes in data IN from the Nec, as also the data in from eeprom goes to data out from Nec.
i dont see any connection to a LCD...

anyway dont care about that, just desolder it and connect it as you where reading a regular 93c66

no, i never had an Enclave here, but i could do it by OBDII with my DP-3 for example..

[sunsation288]

The data out goes in data IN from the Nec, as also the data in from eeprom goes to data out from Nec.
i dont see any connection to a LCD...

my bad sorry to misleading you ...but in the pdf of the NEC micro upd70f3421 you can assign to a lcd display (pin 91 to pin 104) , but i re-read my pdf you can also assign it to
pin =91 sckb1 OR seg 20 of a LCD
pin=92 sob1 OR seg 21 of a LCD
pin=93 sib1 OR seg 22 of a LCD
many thanks to have take time for me
i have see the light i think
Regards

[digimile]

here is the picture of dash by speedoshop and pinouts for upa is same.calculate with tachosoft ans swap bites.

[sunsation288]

Thanks Digimile , you photo is for a Acadia and a Saturn Outlook , i will try to compare with my picture , and let you know , thanks for sharing
http://img.photobucket.com/albums/v235/25outlaw/aaa/P1060600mod.jpg

[borshch]

Hers is the pic BTW, i try to read it on board back then = No Success

so best is to unsolder , so you don't lose any DATA.
which pin is pin1 ?

[neospeedo]

take a look at post #16 nice diagram

[borshch]

take a look at post #16 nice diagram

thats a diferent kind of circuit board.

but i figured out the pins on the one i have