PDA

View Full Version : Kangoo_1,5_DDCR



SergejVita
31st December, 2011, 12:41 PM
Hello, The question I want to ask who knows, perhaps if read and write firmware in the ECU RenaultKangoo DDCR 1,5? Not block sorting through diagnostic connector or connecting shot .-???

Novik_UA
31st December, 2011, 02:53 PM
Don't understand for 100% question, but you can read/write DDCR via diagnostic connector, no problem.
Just don't run engine for 5 minutes after write, and you will not lost injectors codes.

SergejVita
31st December, 2011, 05:51 PM
the question is, what program can be read / write? tried KWP2000, Galletto1250-negative results. ?

Novik_UA
31st December, 2011, 06:02 PM
I read/write few times with MPPS, Galetto do it too.
The only problem is possibility to lost injectors codes.

SergejVita
31st December, 2011, 06:10 PM
I can not read by Galletto-unit 8200331477, motor 65kW 1.5. (see personal communication)

powertdi
1st January, 2012, 09:08 AM
Galleto chinese can do it. But just table read. Try EU4 option for read.

SergejVita
1st January, 2012, 11:07 AM
tried E4: the result is read IDs, and then-"error SK1-9"

powertdi
1st January, 2012, 06:49 PM
So, find a better tool . MPPS chinese also can do this job,like obd and boot mode( full) reading.
Are we talking about DDCR 1.2 ( Delphi)?

SergejVita
1st January, 2012, 07:22 PM
is something that could read Galletto-8200 335 859
************************************************** * 8200 331 477
************************************************** * 8200129 109

pvl
2nd January, 2012, 05:44 AM
Did you tried ALL options EU3 and EU4 ?

You can try also the option in Galletto for the Kia carnival 2.9
It has the same ecu. Reading it, shall not harm anything.

Time for bootmode-action with Galletto:

Choose the v.a.g. 1.8T model with the 400bb-chip.
Yes, the readout will be 512kb, but it is easy to
later-on spilt the software up in to 2 x 256kb files.

See pictures attached for Special instructions

Let us know if it worked, and please post the file when it worked over here.

Thanks,

Cheers,

PvL

SergejVita
2nd January, 2012, 12:44 PM
as KiaCarnaval-wrote "error 1-5". As VAG1, 8t-error: no "BootMode". Blok am unable to make out-I just do not try parsing, "writes / writes not ".... unfortunately ...

pvl
2nd January, 2012, 02:20 PM
I also saw kwp2000+ has a renault DCR section in it. And that Mpps would also support this ecu. You perhaps could try one of these interfaces ? Perhaps a friend owns one of these and you may test it ?

Hope to hear from you soon, how it went,

Cheers,

PvL

SergejVita
2nd January, 2012, 06:36 PM
"KWP2000" also identifies the block-just like Galletti, and does not read .... I've already tried KWP.

pvl
2nd January, 2012, 06:39 PM
Hmm it seems that someting doesn't work-out like it should. Most people are able to read it. Did you try this in the car via obd AND on the workbench via the pinout of my earlier post ?

Ifyes, then the only thing to do, is to see if MPPS does the job. People have been reporting that they could read-out 1.5 ddcr's from clio's and kangoos with it.

Hope that this helps you a bit..

Cheers,

PvL

SergejVita
2nd January, 2012, 07:53 PM
in the near future I intend to buy MPPS and try to do with it ...

darwins
18th June, 2012, 11:05 AM
I have the same problem reading this on the bench using Galletto pvl (http://www.digital-kaos.co.uk/forums/members/65573-pvl/) (few posts up) picture shows a boot mode point.

The flash is positioned lower, PIN 44 flash lines almost with pin 1 shown on board.

I think there must be a different boot mode variant ?


It looks like Galletto & MPPS will only do this if the unit has a Siemens Processor & this one does not..