immo off hyundai santafe' 2.0crdi

[alexbit68]

Hello friends I have a hyundai Santafe '0281010315 ECU with immobilizer locked, I do not have the pin code to put in motion with emergency procedures, how can I fix it? I have to read the eeprom? as you can 'scodificare total? with friends

[aksimo]

Hello friends I have a hyundai Santafe '0281010315 ECU with immobilizer locked, I do not have the pin code to put in motion with emergency procedures, how can I fix it? I have to read the eeprom? as you can 'scodificare total? with friends

Hallo If you need pin send me the vin?

[alexbit68]

I read the file of EEPROM can now get the code? thanks

[EssexTech]

How old is the vehicle.

[alexbit68]

age 2002 ecu is bosch 02810101315 edc15c7 hyundai santafe' 2.0 crdi.

[aksimo]

I read the file of EEPROM can now get the code? thanks

It can only be done virgin not off.

You need Simulator for make it immo off

[aksimo]

I read the file of EEPROM can now get the code? thanks

And for immo pin code I need you car vin code!

[smalliron]

I read the file of EEPROM can now get the code? thanks

Your pin code is: 53 22 88
Simply program the key and all will be OK

[alexbit68]

hello how do I write the code, I use the texa but when I go to reset immobilizer insert the figure tells me that the failed operation, also under the immobilizer pilot light does not light, there also 4-digit code, how can I put hello thanks at all

[aksimo]

A little info for you

[alexbit68]

a texa I did not write it, unfortunately, repeat the pin and the masterkey nn are, someone knows how far the coil inside the immobilizer antenna I doubt arises that is the problem that blocks everything, even XKE 'real estate in the light framework does not turn on, hello and thanks

[aksimo]

a texa I did not write it, unfortunately, repeat the pin and the masterkey nn are, someone knows how far the coil inside the immobilizer antenna I doubt arises that is the problem that blocks everything, even XKE 'real estate in the light framework does not turn on, hello and thanks

If the immo box not work right, any more buy an emulator and we recode the ecu ,and going to drive again :manuflag:

Universal emulator - can emulate Mercedes ESL, erase VAG, BMW errors, all BMW, Mercedes, Fiat, Mazda, Suzuki, Opel airbag occupancy sensor (mat sensor), Renault dashboard CAN bus, BMW I-bus (http://www.codecard.lt/electronics/universal-emulator-can-emulate-mercedes-esl-erase-vag-bmw-errors-all-bmw-mercedes-fiat-mazda-suzuki-opel-airbag-occupancy-sensor-mat-sensor-renault-dashboard-can-bus-bmw-i-bus/prod_331.html)

[smalliron]

a texa I did not write it, unfortunately, repeat the pin and the masterkey nn are, someone knows how far the coil inside the immobilizer antenna I doubt arises that is the problem that blocks everything, even XKE 'real estate in the light framework does not turn on, hello and thanks

Mate, I don't understand your problem. Did you try to reprogram the keys with the pin code that I told you? Reprogram the keys and everything will be fine!

[aksimo]

Mate, I don't understand your problem. Did you try to reprogram the keys with the pin code that I told you? Reprogram the keys and everything will be fine!

I understand that his device does not able program the keys or the immo box is dead.

[alexbit68]

prejudice to the problem, and friends 'texa think that the diagnosis does not write the code, because' in the diagnosis of tells me that the immobilizer key is not recognized and blocked immobilizer control unit, when I enter the enter the 6 digit pin, texa tells me I should not be bene.altri programs which are able to write? Thanks to all

[aksimo]

prejudice to the problem, and friends 'texa think that the diagnosis does not write the code, because' in the diagnosis of tells me that the immobilizer key is not recognized and blocked immobilizer control unit, when I enter the enter the 6 digit pin, texa tells me I should not be bene.altri programs which are able to write? Thanks to all

Ok. possible that you immo box corrupted sw or hw and If anyone can give you working dump for you box . Then it is possible that you can fix it.

[alexbit68]

you mean the engine ECU of HDW and sw? or the immobilizer module which is under the direction Arria conditioning?

[aksimo]

you mean the engine ECU of HDW and sw? or the immobilizer module which is under the direction Arria conditioning?

no Immo box only

[EssexTech]

Alex

You have a Smatra system on you Vehicle. What happens is the key sends it signal to the immobiliser box which then sends a signal to the ecu.

Is it a 6 pin code or 4 pin access code that you need.

If its 4 pin then 2345 is the pin to get into the system unless someone has entered something else. I have a HYundai Hi Scan which is obviously the proper tool.

PM me you email address and I will send you some info

[smalliron]

Alex

You have a Smatra system on you Vehicle. What happens is the key sends it signal to the immobiliser box which then sends a signal to the ecu.

Is it a 6 pin code or 4 pin access code that you need.

If its 4 pin then 2345 is the pin to get into the system unless someone has entered something else. I have a HYundai Hi Scan which is obviously the proper tool.

PM me you email address and I will send you some info

Friend take a look at his EEPROM dump. The Pin code is 6 digits and I have already written the pin code above. My advice is to find some good software that can program keys for Hyundai and use it.

[alexbit68]

friends immobilizer module is behind this group has no ventilation:
HYUNDAI 95400-02500 BOSCH FOO5V00141 VIM223
this and the number just above the black box. There is no other way to write.

[alexbit68]

friends and prejudice 'can write code with this tool?
OBD2 Car SBB Key Programmer New V33 Super Car SBB key programmer immobilizer key code reader univeral key programming tool SBB

[smalliron]

Man, where are you from? I will try to explain in your native language. I don't understand you at all and I think you did not understand what I tried to tell you several times in this thread...

[alexbit68]

dear friend, thanks for your help you but in fact, but I do not speak English well 'cause I'm Italian, if you can help me out thanks.

[EssexTech]

Friend take a look at his EEPROM dump. The Pin code is 6 digits and I have already written the pin code above. My advice is to find some good software that can program keys for Hyundai and use it.

I have just sent Alex the immobiliser training manual for Hyundai to help him out. Carman Scan will be best for the keys

[alexbit68]

friends someone has a wiring diagram for the function key, the immobilizer control unit, I want to make a change with a real estate unit, used

[EssexTech]

I will send you one .

[alexbit68]

because you are kind, send me soon I want to understand how to change

[EssexTech]

On its way geezer:D

[alexbit68]

Hello friend you have found the pattern for me, thanks

[alexbit68]

thanks for diagram hyundai immobilizer, now I am a black outline box alpha code 166 bosch want to try changing the immobilizer with friends
I got to drive a wrecker unit code, a key with the antenna,
someone help me code for the box scheme, there are 6 wires: red / black, black / white, black, green / yellow, brown / white, yellow / red, I need to connect

[EssexTech]

thanks for diagram hyundai immobilizer, now I am a black outline box alpha code 166 bosch want to try changing the immobilizer with friends
I got to drive a wrecker unit code, a key with the antenna,
someone help me code for the box scheme, there are 6 wires: red / black, black / white, black, green / yellow, brown / white, yellow / red, I need to connect

Alex the translation from your language to English has not translated well. Can you try a different translation engine

[alexbit68]

wondering if you could edit box hyundai immobilizer, for a model, FIAT, LANCIA, ALFA.

[EssexTech]

No they are not interchangable

[alexbit68]

thanks for your help ESSEX tell you the value in volts must exit code hyundai box, I tried it with my voltmeter, I 12v, that's right

now it is no doubt that the ECU could be faulty, we try to ECU

[alexbit68]

someone tells me where I can find this box code hyundai F005V00141/VIM223 thanks to all friends

[gadroulll]

i would try in your case.first to unlock ecu you must use a immobox with the keys inside not deleted.
leave the for 3 hour with open ignition.
use your immobox and you must have the right pin code and new keys to program .(if your immobox has erased keys you must load a file with keys inside and important to have the correct pin code)

enjoy your drive

[EssexTech]

Alex. The Smatra line to the ECU can be checked with an oscilliscope.

[alexbit68]

i would try in your case.first to unlock ecu you must use a immobox with the keys inside not deleted.
leave the for 3 hour with open ignition.
use your immobox and you must have the right pin code and new keys to program .(if your immobox has erased keys you must load a file with keys inside and important to have the correct pin code)

enjoy your drive


Hello GAD. can explain why with my translation is not clear, you say that I can use another code box for

[gadroulll]

you must use a working immobox that its eeprom conatin keys data. the ecu is blocked until it see the keys inside the immobox.

if you have tried to program keys with carman the immobox has delete the keys and your immobox is empty

[EssexTech]

Hyundai actually make Engine Ecus without the immobilser in them. I have one for a right hand drive ..

[alexbit68]

Hi friends I managed to find a box with the key code

[jset]

does any one have a solution with emulator to put this ecu with immo off
please

[Riixen]

hy please i want immo off hyundai accent 0281015603 please somody can help me