View Full Version : HOW TO DESOLDER EEPROM, WHERE WHEN NOT MELT WELDING AND DAMAGE THE EEPROM OF GRAPHITE
javiercj
12th January, 2012, 08:07 PM
Hello friends
you happened to try to remove the welding of an eeprom of 8 pins of an airbag unit circuit, there is no way to remove the Tin.
I have done many and micros motorolla etc.
Remove welding with station, hot air and without any problem.
Therefore well today has gone.
was a unit of airbag and the eeprom circuit there is no way to desolder. to the finao graphite from the eeprom has burned and not
has desolder
there is any product that does not happen more, avoid damaging the circuit and not burn the eeprom memory, and allows desolder.
thanks
hope answer
circuit came with a kind of enamel even so there is no way
thanks
help please
ovi_dk
12th January, 2012, 08:12 PM
Tell the type of module maybe sombode can give u the pinout.
B.R
javiercj
12th January, 2012, 08:17 PM
Tell the type of module maybe sombode can give u the pinout.
B.R
Hello
thank you for answering the switchboard of airbag;
autoliv
550-80-44-00 //8200 018 830
eeprom is 93c66
thanks I hope answer
Youneselm
12th January, 2012, 08:58 PM
you can desolder it with hot air
ominimicu
12th January, 2012, 10:59 PM
you should have used acetone on it first, and rub it or lightly scratch it. afterwards desolder usind the smallest adapter for the hot air, directing the flow only at the pins.
javiercj
12th January, 2012, 11:16 PM
you can desolder it with hot air
hello youneselmoukhtari
thanks for your resquest
i am desoder with hot air
thanks
javiercj
12th January, 2012, 11:25 PM
you should have used acetone on it first, and rub it or lightly scratch it. afterwards desolder usind the smallest adapter for the hot air, directing the flow only at the pins.
Hi
thanks for responding.
Of acetone not what had done, that usually make either scratched before desolder to clean a little lacquer.
But I will try to use first acetone.
If air directly address it pins and when micros motorolla are what I do is the first direct hot air in the pins and also about the micro.
thank you very much for helping
temperature must be used with the station of hot air??
thanks
javiercj
12th January, 2012, 11:40 PM
hello.
Thank you all for help.
But the damage to the circuit was done,
to burn the tracks of the circuit
I finally managed to remove the eeprom but the tracks are burned
There may be possibility to connect an eeprom again
but with detail on image to see the photo of the tracks of the circuit of airbag unit
airbag control box is:
airbag 550 80 44 00 8200018830
You can help
But in the image of the circuit you can see the tracks that is below the eeprom
I hope help
Thank you
Where can I find?
Youneselm
15th January, 2012, 12:06 AM
there are tracklabels to fix pbroken or damaged tracks.
here is the link that you need made
Kaisertech Ltd PCB Track Repair Kits (http://www.kaisertech.co.uk/acatalog/Products__PCB_Track_Repair_Kits_452.html)
did it serveral times works 100 percent good, no complains after 3jears yet
press thanks if it was helpfull
ominimicu
15th January, 2012, 11:48 PM
follow the tracks and join the eprom pins with cables to the next possible point.:D skip the tracks
Youneselm
16th January, 2012, 12:03 AM
thats also an option, but not so clean.
with the pads its verry clean and profesionel job.
javiercj
16th January, 2012, 08:45 AM
follow the tracks and join the eprom pins with cables to the next possible point.:D skip the tracks
If.
that do when leave the track.
but as they have broken several tracks, no longer is that track corresponds to each leg of the eeprom.
Therefore needed to see a clear picture with the eeprom removed the switchboard of airbag.
circuit
thank you
javiercj
16th January, 2012, 08:57 AM
thats also an option, but not so clean.
with the pads its verry clean and profesionel job.
Hello
next time
good clean legs, remove enamel, use acetone, and read the eeprom
thank you
driiven
8th February, 2012, 10:26 PM
Chip Quik: Easy removal of surface mounted devices (http://www.chipquik.com/) this will help you
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.