PDA

View Full Version : Star Diagnosis C3 - need help


aglinsky
24th January, 2012, 08:08 AM
Hello!
I need help with repair Star c3.
Ceasar test:

Selfdiagnostic
==============

Device: Part D
Toolkit-Resultcode: 1

SDconnect Toolkit - device diagnostic - Part D
==============================================

CAESAR STOS+ Rev.:2.12 from Jun 16 2005
generated protocol file from 24.08.2011 20:53
SystemCheck :
Check serial ... 0 Ok
CAESAR HW Detection :
D2Access ... 0 Ok
D2DownLoad ... 0 Ok

CAESAR Part D2 detected on COM2 with baudrate: 19200
CAESAR version check :
D2CheckSNVER ... 0 Ok
User is Daimler-Benz AG
User Authentification 1
Classification 0
Serial Number XXXXXX
Authorization Level 4
Part D
Hardware Authentification XXXXXX
Hardware Date XXXXXX
Special EEPROM check :
D2 Special EEPROM check:
Inst. date registered ... 0 Ok
D2 Special CAN Test :
Special Test ... 0 Ok
CAESAR version check :
D2CheckSNVER ... 0 Ok
User is Daimler-Benz AG
User Authentification 1
Classification 0
Serial Number 110464
Authorization Level 4
Part D
Hardware Authentification XXXXXX
Hardware Date XXXXXX
Slave check :
D2 Slave check
D2 Processor ... 0 Ok C165 (mask step CA) is mounted.
D2 RAM ... 0 Ok
D2 FLASH ... 0 Ok
D2 EEPROM ... 0 Ok
D2 SERCTL1 ... 0 Ok
D2 UART1/2 ... 0 Ok
D2 ADC ... 0 Ok
D2 Display Power Supply :
D2 Power Battery ... Voltage KL30 = 12.2 V
D2 Power Ignition ... Voltage KL15 = 00.3 V
D2 Voltage K-Lines :
D2 State K-Lines (35) ... Total 1 (+), 34 (-)

I changed TIP42 and other voltage chips - same result.
When I connect to car - das write voltage 1.1V
What is the problem with?
Thanks a lot advance!
P.S. Sorry for my english.
sapperjon
24th January, 2012, 10:03 AM
KL30=1.1V or KL15=1.1V ?
aglinsky
24th January, 2012, 10:17 AM
sapperjon
In DAS - 1,1V in car (w211). in fact - 12,7

In Caesar test -
D2 Power Battery ... Voltage KL30 = 12.2 V
D2 Power Ignition ... Voltage KL15 = 00.3 V
sapperjon
24th January, 2012, 07:27 PM
Check up power on 16pin DLC
aglinsky
25th January, 2012, 06:31 AM
same as car - 13v
sapperjon
25th January, 2012, 08:38 PM
What version DAS? Try to reinstall DAS.
jacm3
25th January, 2012, 09:38 PM
You have D3 or D4 pcb? check bcp56
sapperjon
26th January, 2012, 08:24 AM
I think a problem the software - no hardware. Selftest OK.
aglinsky
27th January, 2012, 05:57 AM
No - It's a real Mux problem.
I checked on some PC. Other mux working fine with all pc. This not work.
DAS 09/2011
DB_member
27th January, 2012, 09:48 AM
Selftest OK.

Self-test was not OK.
aglinsky
27th January, 2012, 02:47 PM
May be I neet change other chips?
Mux c3 - china.
may be anybody have expirience...
aglinsky
29th January, 2012, 09:17 PM
no solution?