View Full Version : audi a8 4.2 tdi 2007 never starts with modified files
loboy
24th January, 2012, 11:38 AM
hey ...
i have tried everything... when i modify the origin file of this car with winols 1.5/1.721 the car doesnt start... of course i do the checksum... when i reflash the ori file the car starts..
does anybody knows the problem? and the solution??
best wishes!
loboy
24th January, 2012, 11:56 AM
here is the file org+modified
macxlulu
24th January, 2012, 12:55 PM
must remove manually ...dpf
P2XA
24th January, 2012, 01:10 PM
ECUSAFE - BIG JOKE
filecloud
24th January, 2012, 02:25 PM
hey ...
i have tried everything... when i modify the origin file of this car with winols 1.5/1.721 the car doesnt start... of course i do the checksum... when i reflash the ori file the car starts..
does anybody knows the problem? and the solution??
best wishes!
You have done both ecus?
powerchip
24th January, 2012, 03:03 PM
you must make 2 ecus !
Master and Slave ! than it will work !
sepistar
24th January, 2012, 04:37 PM
You have done both ecus?
That's why car don't start!
Best regards
loboy
25th January, 2012, 11:28 AM
hi!
yes of course.. can i use the one tuned file in both ecus?
powerchip
25th January, 2012, 12:00 PM
read 2 ecus and check the files in winols !
ask that tuner that have make the mod file !
he must know that you need a master and slave file !
if he doesnt know that this car have 2 ecus ! ui ui ui than that
tuner knows nothing about cars !
this is what i think !!!
loboy
25th January, 2012, 12:56 PM
hi the tuning was made be me..
it is my own car. of course i know it has 2 ecus.
but i found out that i can use the same file in the 2 ecus.
a user was very friendly an made the checksum by his swiftec program.
and the car starts! :-)
but there ist one big problem. after a few meters the car goes in fault mode with less power.. but there is no limp mode or fault code.
i think my ecusafe 2.0 does not a good job.
please help me. who can shut off this mode?
thanks a lot.
i will attach the swiftec file which works with both ecus and the org (flash.bin).
filecloud
25th January, 2012, 02:37 PM
Hello
- The tuning is absolute nonsense. Totally stupid!
- ECUsafe does not work
- Car goes into limp mode because calculation limiters have been exceeded by far.
Do you really know what you are doing? You requested 1100Nm in drivers wish and gain from 670Nm to 870Nm in torque.
-> Go to a good tuner
otzi
25th January, 2012, 02:51 PM
hi the tuning was made be me..
it is my own car. of course i know it has 2 ecus.
but i found out that i can use the same file in the 2 ecus.
a user was very friendly an made the checksum by his swiftec program.
and the car starts! :-)
but there ist one big problem. after a few meters the car goes in fault mode with less power.. but there is no limp mode or fault code.
i think my ecusafe 2.0 does not a good job.
please help me. who can shut off this mode?
thanks a lot.
i will attach the swiftec file which works with both ecus and the org (flash.bin).
Hi,
Go to the local tuners and you resolve your tun file
Learn by edc15 car
kill 1,9 tdi engine not 4.2 engine:beheaded:
BR
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.