View Full Version : x-prog m failed to read EWS 2 OD46J...
mburu
25th January, 2012, 11:16 AM
Hi everyone, i tried reading EWS 2 mcu OD46J using X-prog m failed error msg timeout error...please help..
milkatrek
25th January, 2012, 11:28 AM
by k-line?
igorr
25th January, 2012, 12:59 PM
if you read thru kline conect mod b directly on mcu,I think it is pin 22 but I am not sure
mburu
26th January, 2012, 11:19 AM
if you read thru kline conect mod b directly on mcu,I think it is pin 22 but I am not sure
i tried using crystal in btw pin 7 n 8 but after reading it was blank......
mburu
20th June, 2012, 05:13 PM
if you read thru kline conect mod b directly on mcu,I think it is pin 22 but I am not sure
hi igorr, just change oscillation n it will work i did it.....
honingkoning
22nd June, 2012, 12:32 AM
hi igorr, just change oscillation n it will work i did it.....
Did you use external power, this will also do the job.
Regards Adam
mburu
2nd July, 2012, 02:09 PM
Did you use external power, this will also do the job.
Regards Adam
nop but i only changed oscillation in Device........
harryauto
2nd July, 2012, 07:39 PM
use 68HC11EA9 (w/Security 0F36W)
Anyone say : use external power, this will also do the job.
or changed oscillation in Device........
Don't Believe him .....
nazz2
2nd July, 2012, 09:53 PM
Problem is with your k line adapter,read my old post, you also have to connect the adapter upside down , not like the picture,which i forgot to mention, previously.also no need for external power.
mburu
5th July, 2012, 05:44 PM
How i changed oscillation to be able to read Od46J using X-prog...
bram380
5th July, 2012, 07:11 PM
Device
MC68HC11EA9 w/o security (0D46J)
Memory
RAM 0x0000-0x01FF RD
ROM 0xD000-0xFFFF RD
EEPROM 0xB600-0xBFFF RD/WR
Programming Interface
In-circuit, On-Board
Packages
PLCC52
Adapters
HC11EA9/E9 programming adapter
(P/C: 1-002-0011)
Important:
If you using on-board programming
interface you must set oscilator
to 5529600 Hz
obdmaster
5th July, 2012, 07:59 PM
Device
MC68HC11EA9 w/o security (0D46J)
Memory
RAM 0x0000-0x01FF RD
ROM 0xD000-0xFFFF RD
EEPROM 0xB600-0xBFFF RD/WR
Programming Interface
In-circuit, On-Board
Packages
PLCC52
Adapters
HC11EA9/E9 programming adapter
(P/C: 1-002-0011)
Important:
If you using on-board programming
interface you must set oscilator
to 5529600 Hz
Yes bram says in instructions,
Cant understand why people dont read them m8!! lol
doctordiag
6th July, 2012, 10:22 AM
the simple way read
by k-line
zapzap
15th December, 2015, 07:53 PM
S?PERSİN
5529600 İLE OKUNDU
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.