Ford transit 2007 FOMOCO

[eiemax]

Hello.
I have read the file of a ford TRANSIT 2007, 2400cc and 140hp. With ECU FoMoCo. I have read with MAGPro2 ver. 4.2.

The data that has read the MAGPro2 are:

Checksum: BCC4
HW: 6C11-12B694-CB
SW: 6c11-12A650-CK
INFO: GSC-5.0-ST10F276
INFO: 6c11-12K532-MH

I want to know if the file that I read, it's ok or incomplete, because ecm not the right numbers, but only incomprehensible signs:

Ford TDCi Visteon
Num SW: ??
??
??
Num HW: ?
??
?
------------------------------
Cks: AD66
Size: 917504 = 0xE0000

why? :motz:

I may know how to exclude the egr from the map?
I have no driver for this ECM ECU, which addresses are to edit the file?

Thanks in advance friends :wavey:

[powertdi]

I think its correct, but OLs cant find cks automatic. Maps look correct .I never did Fomoco from Big transit, but small transit conect maps look same.

[eiemax]

You know I give the addresses, and how to close the EGR?
thanks

P.S: with MAGPro2 the checksum is automatically

[ominimicu]

i did one of those..and it was like 800kb but i wrote it..and everything went fine.

[eiemax]

You have the addresses for this ECU?
thanks

[eiemax]

Nobody has any idea about the address?
thanks

[LaraVAG]

Read correct, its visteon ECU some of maps:

Turbo pressure:
B4fCE 16x16 (1 of 4)
B5C8E 16x16 (1 of 4)
B694E 16x16 (1 of 4)

SOI
B0400 16x16 ( 1 of 8 )
SOI limiter
B1D80 16x16 (1 of 4 )

Nm to mg
98000 16x16 (1 of 5)
AEAEA 16x16 (1of 7)

TOI ?
BAe36

CR pressuer
A8b82 16x16 (1 of 8)

and meny more

[eiemax]

Thanks friends...
I did not understand what are the definitions:

SOI, Nm to mg, TOI ?,

CR pressuer, is common rail pressure?

you know to close the egr on this file?
thanks in advance

[filecloud]

I think its correct, but OLs cant find cks automatic. Maps look correct .I never did Fomoco from Big transit, but small transit conect maps look same.

Hello
This is not correct! Winols detects the checksum perfect. OLS811 Visteon ST10. And the checksum is fine.

It would be fair not to post such false statements based on clone tools or far outdated cracked programs as a referrence.
Some people here may consider to buy the tools legally because they want to work on a professional basis. For them it is important to get valuable feedback. Winols handles the file fine, Alientech KessV2 and others can read and write the file fine; And the flashtool also takes care about the checksum.
greetings,
filecloud

[LaraVAG]

CR preesure - Common Rail Pressure
SOI - Start of Injection
TOI - Time of Injection
Nm to mg - conversion map

[eiemax]

you know the address of 'EGR?
thanks

[J_amb_o]

Hi All, read the attached file with genuine Magpro2, can someone help with map locations please? Never done one before.

J.

[javiercj]

Hello.
I have read the file of a ford TRANSIT 2007, 2400cc and 140hp. With ECU FoMoCo. I have read with MAGPro2 ver. 4.2.

The data that has read the MAGPro2 are:

Checksum: BCC4
HW: 6C11-12B694-CB
SW: 6c11-12A650-CK
INFO: GSC-5.0-ST10F276
INFO: 6c11-12K532-MH

I want to know if the file that I read, it's ok or incomplete, because ecm not the right numbers, but only incomprehensible signs:

Ford TDCi Visteon
Num SW: ??
??
??
Num HW: ?
??
?
------------------------------
Cks: AD66
Size: 917504 = 0xE0000

why? :motz:

I may know how to exclude the egr from the map?
I have no driver for this ECM ECU, which addresses are to edit the file?

Thanks in advance friends :wavey:

Hello

I do have the same unit fomoco6c11-12a650 of Ford Transit 07-08 2400cc
and I need to read the unit to clon it....can you tell me the conexions and the interfaz you?ve used?
thank you very much
i wait for your reply

[eiemax]

I used magpro2 (flashtec) clone and is ok...

[furburger]

TOI/Duration is at BBAD2

[javiercj]

I used magpro2 (flashtec) clone and is ok...


but

it read/write? magpro st10 flash???

[bellautos]

If you disable the EGR by flash you will need to also disable the Mil light for it. Xprog does this ecu very well also.

Pete

[javiercj]

If you disable the EGR by flash you will need to also disable the Mil light for it. Xprog does this ecu very well also.

Pete

You can explain also how to cancel the egr in cartography, to locate the egr map?

And as you can read this ecu, with xprog-m

that connections make to read and to write the flash and eeprom

hope your help and the form of connection

thanks

[kevfield]

And as you can read this ecu, with xprog-m

that connections make to read and to write the flash and eeprom

hope your help and the form of connection

thanks[/QUOTE]

If you have xprog you can find this info out easy !

[furburger]

Is there an e2p in this ecu?

[javiercj]

And as you can read this ecu, with xprog-m

that connections make to read and to write the flash and eeprom

hope your help and the form of connection

thanks

If you have xprog you can find this info out easy ![/QUOTE]

because in the file info of xprog-m is how to make the connection.



but this connection make it in the micro does in that leg to make the connection and that information does not come in the st10 micro flash



help please to identify correct connections of the micro with the connection of the xprog-m

[kevfield]

Pins for st10

Thanks kev

[javiercj]

Pins for st10

Thanks kev

ok

yes in the the case st10276 it is appear the pins conexion

but in the case st10280 it is no appear the pins conecxion, for the unit delphi

[kevfield]

make photo of pcb ecu the the

Thanks kev

[furburger]

I'm reading in boot mode with BS.. only seeing 832kb file ., you can read more bytes or another memory with x-prog m?

[javiercj]

make photo of pcb ecu the the

Thanks kev

tomorrow

to do the photo pf pcb ecu

thanks

[javiercj]

tomorrow

to do the photo pf pcb ecu

thanks


here you have the picturess the engine unit with micro st10f280 (flash).

i need to read/write eeprom/flash of these micro stflash

please how do i do the conextions with programmer xprog-m?

i wait for your replay

thnaks

[Dyrygent]

507120
pinout connection dcu102 read ktag507122