steve67474
3rd February, 2012, 11:03 AM
Hi Guys. I have just loaded this file on my PC...OSCAM-1.10svn6089-i386-pc-cygwin-libusb-pcsc-webif-OSCAM_LoaderV0.1.4 and tried to configure a smargo on it. I followed these directions to the letter...
1. Unpack the tools zip file to Desktop
2. Plug the smargo into a USB port on your PC.
3. Windows will detect the new device.
4. Do a manual drivers install , pointing to the Drivers_Windows folder.
5. It will prompt for drivers for the USB device , then again for the serial device.
OK, the drivers are installed
UPPGRADE FIRMWARE
Make sure the smargo is plugged into the PC with NO viewing card in it.
Firstly, we need to check the smargo firmware version, so run the SmartreaderUpdate.exe
If the firmware is v1.4 it will say so in the status bar at the bottom of the window and you can close this util,
if not, click the update button and it will apply the update.
CHANGE PORT COM NUMBERS
on your pc
in device drivers > PORT COM & LPT >
you have a new interface : USB Serial Port com (com xx) xx it's a port number
right click > propriety > port setting > advanced >
change : COM Port number
Then I did this to Identify the Bus No.
command for looking N? of BUS:DEV for Oscam loader cygwin
run cmd in windows
type cd c:\Oscam\OSCam <= path folder oscam on your HDD for me it's C:\Oscam
type list_smargo.exe
other windows open with
FTDI
bus:dev 002:003
Device Serial:Reader xxx for me xxx = 227 =>
oscam device = Serial:Reader 227
start Oscam_Loader
chose : smartreader
detect : CD
device : Serial:Reader xxx
caid : your caid card
label : your name card nc bis sly ect
The result was this???
Microsoft Windows [Version 6.1.7601]
Copyright (c) 2009 Microsoft Corporation. All rights reserved.
C:\Users\Steve>cd desktop
C:\Users\Steve\Desktop>cd oscam
C:\Users\Steve\Desktop\OSCAM>cd oscam-1.10
C:\Users\Steve\Desktop\OSCAM\OSCAM-1.10>cd oscam
C:\Users\Steve\Desktop\OSCAM\OSCAM-1.10\Oscam>list_smargo
Looking for smartreader with an out endpoint = 0x82 :
coulnd't open device 006:001
C:\Users\Steve\Desktop\OSCAM\OSCAM-1.10\Oscam>
Any ideas whats going wrong guys. I did the driver update and this is my driver in Device manager...
1. Unpack the tools zip file to Desktop
2. Plug the smargo into a USB port on your PC.
3. Windows will detect the new device.
4. Do a manual drivers install , pointing to the Drivers_Windows folder.
5. It will prompt for drivers for the USB device , then again for the serial device.
OK, the drivers are installed
UPPGRADE FIRMWARE
Make sure the smargo is plugged into the PC with NO viewing card in it.
Firstly, we need to check the smargo firmware version, so run the SmartreaderUpdate.exe
If the firmware is v1.4 it will say so in the status bar at the bottom of the window and you can close this util,
if not, click the update button and it will apply the update.
CHANGE PORT COM NUMBERS
on your pc
in device drivers > PORT COM & LPT >
you have a new interface : USB Serial Port com (com xx) xx it's a port number
right click > propriety > port setting > advanced >
change : COM Port number
Then I did this to Identify the Bus No.
command for looking N? of BUS:DEV for Oscam loader cygwin
run cmd in windows
type cd c:\Oscam\OSCam <= path folder oscam on your HDD for me it's C:\Oscam
type list_smargo.exe
other windows open with
FTDI
bus:dev 002:003
Device Serial:Reader xxx for me xxx = 227 =>
oscam device = Serial:Reader 227
start Oscam_Loader
chose : smartreader
detect : CD
device : Serial:Reader xxx
caid : your caid card
label : your name card nc bis sly ect
The result was this???
Microsoft Windows [Version 6.1.7601]
Copyright (c) 2009 Microsoft Corporation. All rights reserved.
C:\Users\Steve>cd desktop
C:\Users\Steve\Desktop>cd oscam
C:\Users\Steve\Desktop\OSCAM>cd oscam-1.10
C:\Users\Steve\Desktop\OSCAM\OSCAM-1.10>cd oscam
C:\Users\Steve\Desktop\OSCAM\OSCAM-1.10\Oscam>list_smargo
Looking for smartreader with an out endpoint = 0x82 :
coulnd't open device 006:001
C:\Users\Steve\Desktop\OSCAM\OSCAM-1.10\Oscam>
Any ideas whats going wrong guys. I did the driver update and this is my driver in Device manager...