MITSUBISHI PEJERO 2003 ENGINE 4M41

[achaccha]

Dear Friends
I need to program a key to a Mitsubishi Pajero 2003. It has tried to program with several programmers including TCODE, but no programming success.
Please I need help in this programming
the programming will be possible to read any memory on the board?
many colleagues have solved this case buying the immo antenna including the new key
IMMO ANTENNA PART NUMBER IS MR329406

[bram380]

Read IC03
Memory device is Motorola HC805P18 - 44 pin QFP

[achaccha]

thank you very much friend to respond, please programmer may suggest that I can use to make this reading? I have UPA, XPROG
regards

[bram380]

need tmpro or etl

[shitad]

Got one of these yesterday to do but keeps saying "No key loaded:.
This is a stolen recovery Car where the Immo was smash up baldy and the Antenna was completely destroy. Customer bought a brand new Immo with New keys and with Ignition cylinder and bracket from Japan.
Using Pin code 5176 Both Sbb and Carman give same error "no keys loaded"
Virgin Immo show zero keys program, the old immo show 2 keys program.
The main board of the old original immo was untouch and seems to be in good condition but the Antenna ring is missing.
I attach a Antenna to the broken immo and try to start but still no start.
How do I register the Virgin Immo ? and program the 3 new keys to it.

Help!!!!

[achaccha]

please friend, can describe the procedures for reading the micro using the ETL?
have to remove the micro plate? or read circuit
I thank you for your help, I need you to guide me step by step
maybe some pictures would help

after getting the reading, this reading is the key?
as would make the programming of new keys?, what kind of key I use for programming?
maybe virgin can be obtained in the reading file
Thanks for your help

[bram380]

Try this tool for read & write hc805p18 (http://www.etlweb.com/?ref=prod_prog_mc68hc805p18)

[puu]

Hello, pin 5176 or 3828 chip tex cripto 62.

[agabna]

hello


mut 3

[keygargoil]

i had one that took a 4d 61 read your chip and post the data

[achaccha]

Thank you very much for your comments friends
I am buying the ETL tool to do this reading
But if there was any other option, to make reading, please let me know
TMpro2 not know that you can read memories and microprocessors as H44H, I would like to know where I can buy this tool
attached to this image immo shipping
regards

[Zohar]

Thank you very much for your comments friends
I am buying the ETL tool to do this reading
But if there was any other option, to make reading, please let me know
TMpro2 not know that you can read memories and microprocessors as H44H, I would like to know where I can buy this tool
attached to this image immo shipping
regards

This tool for developments only and ETL do not selling that. Easiest way - immoff in ECU.

BR

[shitad]

How do you do Immo off for this car ?

[Zohar]

How do you do Immo off for this car ?

You should read flash from MCU MH830x (in most cases this is MH8301/02 with 512KB on board) in ECU and then send dump to me. Piasisni, MMC Flasher and Powergate can do this job.

BR

[shitad]

You should read flash from MCU MH830x (in most cases this is MH8301/02 with 512KB on board) in ECU and then send dump to me. Piasisni, MMC Flasher and Powergate can do this job.

BR


I have Tactrix open Port 2.0 and I see on http://ecutools.ru/chip-tuning-equipment/mmc-flasher/
that it can be used with MMC Flasher, do you know if this will work ? if so I will search for MMC software. I also already have the Tactrix software.

[Zohar]

I have Tactrix open Port 2.0 and I see on MMC Flasher - ???????????? - ???????????? ??? ???-??????? ? ??????????? - ECUTools.ru (http://ecutools.ru/chip-tuning-equipment/mmc-flasher/)
that it can be used with MMC Flasher, do you know if this will work ? if so I will search for MMC software. I also already have the Tactrix software.

Tactrix Openport 2.0, Mangoose and others j2534 adapters is supported.
MMCFlasher work perfect with this ECU type (via OBDII). This is link on official MMC Flasher forum (support page for english users - MMCFLASH -> For English Users (http://mmcflash.ru/forum/index.php?showforum=9)
If you have any questions about MMCFlasher - ask them at this forum from developer.

BR

[jebo]

Dear Friends
I need to program a key to a Mitsubishi Pajero 2003. It has tried to program with several programmers including TCODE, but no programming success.
Please I need help in this programming
the programming will be possible to read any memory on the board?
many colleagues have solved this case buying the immo antenna including the new key
IMMO ANTENNA PART NUMBER IS MR329406

hi,

i have same experience before.
i used x431 master to program the key into immo.
check this:
http://www.digital-kaos.co.uk/forums/f177/4d-62-tpx2-beginners-question-240342/index2.html#post1346770

[shitad]

Here is my dump can anyone immo off it for me. ECU part # MK344949