mazda3 2005

[ivanrpm]

Hi bros, I have 3 days with headache, there is someone wants to roll back a mazda3 2005, recently I sincron one mazda3 but this is so hard, look, the secure bits are fine but this does not let me to program keys and offcourse never turn off the inmo light, I think this a problem of ecu or dash but not sincron, this car has 93c56 in dash and 93aa66 in ecu, to get eeprom in ecu you have to desold all the pins of the ecu.
Any comemts about this problem I really apreciate, or experiences on it!


Many thanks
Regards

[gokey]

have a similar problem !!
not resolved

[workdamnyou]

2 minute job with AD100 Pro.

[gokey]

http://www.digital-kaos.co.uk/forums/f178/mazda-3-2005-not-start-248345/

[ivanrpm]

2 minute job with AD100 Pro.
But I am using IDS original Scantool, when it ask about incode I calculate the incode but this shows me that the incode is incorrect?

Regards

[workdamnyou]

Post your code.

[ivanrpm]

Post your code.

ok i will do that tomorrow!thanks

[ivanrpm]

Hi I discover that the problem is the dash file is not enought sincron, so if someone can finish to sincron it I really apreciate!

MANY THANKS
REGARDS

[ivanrpm]

Post your code.

My outcode is 5E242D in both hec and pcm, the incode I find is 249D, dO YOU HAVE ANOTHER FOR THIS?

[cjawahir]

hi install this file in dash , use two keys switch ignition on until immo light goes out switch off do the same for next key .

cj

[ivanrpm]

Hi bro, thanks for help, but this is a file for 93c56 eeprom dash, because I tryied to open with upa and it is longer than 93c56 and tell me this is an inmo off?

Regards

[cjawahir]

hello its not an immo off , here i upload again this time with winrar,

cj

[Min2xx]

I have the same problem with mazda 6. New ecu and one orig key, can't add key, can't add new ecu.
can I use this dash dump for mazda 6 for add keys?

[LegendPT]

hello its not an immo off , here i upload again this time with winrar,

cj
Hi,

I have tried your solution an it works. the problem is that i dont have the cluster working with this dump. Can you please check the dump attached?

[cjawahir]

Hi,

I have tried your solution an it works. the problem is that i dont have the cluster working with this dump. Can you please check the dump attached?

ok here is another file for your cluster try it , let me know .

cj

[LegendPT]

Thank you cjawahir,

I have tried right now, and does not work. :(
With the previous dump that you post, the car starts

Thank you anyway

[bender]

Thank you cjawahir,

I have tried right now, and does not work. :(
With the previous dump that you post, the car starts

Thank you anyway

I did tried the previous dump with 2 turns key on, won't start.
How did you manage to do it?

My dump is damage somewhere where there is immo.
dump still works ok,

[bender]

hi install this file in dash , use two keys switch ignition on until immo light goes out switch off do the same for next key .

cj

I'm really desperate, use 2 keys? If I only got 1 key do I have to buy another key before I can use this solution? or is there
a one key solution?

[autofan1965]

Ford and mazda need at least two keys programmed. Otherway you cant start car.

[cjawahir]

Ford and mazda need at least two keys programmed. Otherway you cant start car.


correct , use two key s .

cj

[bandyhafa]

is it possible to get a dump with 2key programmed preloaded ?
my mazda3 2005 have only one key and after changing with a new PCM it says that can't comunicate with instrument cluster
IDS says CAN disabled
how can i start my car please

[deondti]

I have a Mazda 3
PCM fault code : theft detected , immobilizer active
Cluster: no fault codes

Attached is PCM dump 93c56 and cluster 93c56 8 and 16 bit as well as key data

Could someone please sync the PCM-Cluster-Keys

I thank you in advance

[autocheck]

HI . HAVE A MAZDA/2 VERISA 2004 WITH ALL KEYS LOST . TRIED TO ADD 2 4D63 NEW KEYS WITHOUT SUCCESS . I have SBB , X100 & MVP but all saying " no key loaded repeat procedure ". how best can i solve this problem? Thanks in advance.

[quattro210]

How far are you from Gaborone?

[gokey]

HI . HAVE A MAZDA/2 VERISA 2004 WITH ALL KEYS LOST . TRIED TO ADD 2 4D63 NEW KEYS WITHOUT SUCCESS . I have SBB , X100 & MVP but all saying " no key loaded repeat procedure ". how best can i solve this problem? Thanks in advance.


first erased all key ?

[PCF]

hello can i try this file on mazda 5 2007 model ? i have same problem cant program key the car was working we lost the key and cant program it show me code error
thanks