View Full Version : immo off land rover
ray978
24th February, 2012, 01:25 PM
Can you tell me the procedure for immo off land rover year 2000 type engine ECU 0281010113 20t2n.
thanks
arielcalcaterra
24th February, 2012, 05:08 PM
Can you tell me the procedure for immo off land rover year 2000 type engine ECU 0281010113 20t2n.
thanks
Try the following instructions.
also bypass the starter
ray978
24th February, 2012, 06:21 PM
Try the following instructions.
also bypass the starter
does not appear that the procedure is this I read that you work on eeprom 93c46 .. but they are still on the high seas :(
ray978
27th February, 2012, 11:31 AM
help my friends
friki
27th February, 2012, 12:06 PM
lift eeprom x2(93c46) from ecu and start your car
ray978
27th February, 2012, 12:23 PM
lift eeprom x2(93c46) from ecu and start your car
I just have to remove the eeprom and the car starts? and the starter can turn?
friki
27th February, 2012, 12:35 PM
yes mate. Will work as if it was the first time :turtle:
ray978
27th February, 2012, 12:36 PM
sorry friend but do not quite understand
joubliss
27th February, 2012, 12:42 PM
remove the left 93c46. and baypass the starter.
friki
27th February, 2012, 12:46 PM
sorry for my englesh. yes mate. Will run
ray978
27th February, 2012, 12:59 PM
remove the left 93c46. and baypass the starter.
where bypass the starter?
ray978
27th February, 2012, 01:54 PM
you have a photo illustration for understanding what is left of the eeprom?
ray978
27th February, 2012, 03:02 PM
remove the left 93c46. and baypass the starter.
removed the left but not the eeprom
joubliss
27th February, 2012, 03:18 PM
Put the socket of ecu down and look for 2 eeproms 93c46 u have to remove the one in LEFT. if u dont understand take a picture and i will show u.
ray978
27th February, 2012, 03:35 PM
Put the socket of ecu down and look for 2 eeproms 93c46 u have to remove the one in LEFT. if u dont understand take a picture and i will show u.
I understand .. only this? because even if the starter motor turns the engine will not start
ray978
27th February, 2012, 03:50 PM
ecuvonix says to unplug the antenna and to bridge black yellow wire (does not say where) then says to load the eeprom and repair software with ecuvonix
ray978
27th February, 2012, 08:06 PM
you do not understand why not go off in real estate. so I would fix the system properly. my problem is that not work is the central locking remote control .. all fuses are correct .. What can have happened?
konop11138
27th February, 2012, 09:48 PM
This is a simply way for yours problem:
- replays side eprom A1-A2
- turn ignitions ON - 60 sec- OFF
- replays side eprom A1-A2
- find master relay
- wire black-yellow (pin 4A) - short to ground
- start engine
Put the universal controler central locking with 2 new remote control, and ready.
Good luck
ray978
27th February, 2012, 10:55 PM
I would like to restore the proper functioning of the central locking .. does not work even with the button on the center consol. I am convinced that if my car away this part .. I would like to know if someone has already happened to this problem
joubliss
28th February, 2012, 09:48 AM
Another andersonmaxi.
ray978
28th February, 2012, 09:58 AM
Another andersonmaxi.
I do not understand
ray978
28th February, 2012, 11:21 AM
someone has a wiring diagram for multifunction control module?
ray978
29th February, 2012, 01:41 PM
car is started .. my fault that I confused with the right eeprom eeprom left. now it remains clear alarm bsi
ray978
1st March, 2012, 09:49 AM
I left the car running for 2 hours and now will not start? :(
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.