Renault Clio 1.2 - S110138000B / 8200059086

[jovime]

Hi guys!

Anyone has an immo off solution for this one?

Renault Clio 1.2 Sirius 32N (NO AIR CONDITIONED) - S110138000B / 8200059086

I've been looking at the forum but all solutions seems to be mainly for 1.4 and 1.6 engines.

I'm attaching original flash read.

Kind regards!

[alfabit]

Hi guys!

Renault Clio 1.2 Sirius 32N
I've been looking at the forum but all solutions seems to be mainly for 1.4 and 1.6 engines.




How did you read that flash ? Flash Am29f200BB ? It doesn`t look like one read by a normal programmer ( yours starts with FA 00 F4 19 .. and not with C0 F0 E4 CA .. as most of Sirius 32 dump looks ).
Read it again with a Willem or GQ-... and then will help you .

[alfabit]

Hi guys!

I'm attaching original flash read.

Kind regards!


You read it by OBD, KWP2000, Galetto, ... or an other " exotic " tool, am i right ?
Desolder the flash and read it with a proper programmer and i bet your Clio will be a happy car ! :top:

[jovime]

You read it by OBD, KWP2000, Galetto, ... or an other " exotic " tool, am i right ?
Desolder the flash and read it with a proper programmer and i bet your Clio will be a happy car ! :top:

It's read in boot mode by original ByteShooter Master, so better to desolder it?

[svrecar]

Use this one. Cut the pin no.58 on the ecu.
If you will have poor idle afterwards, use Renault Clip to configure it with AC option set to ON.
It is a known bug in software.

Pass in PM.

[jovime]

Yope! You're right, all dumps start different...

But it does not make sense at all... reading it in boot mode gives you direct access to all flash area, without restrictions. It's the first time that BS does something like this and I'm using it daily for BOOT purposes flawlessly.

Something is strange here. Problem is that I made dump virgin and wrote it to the ECU, so if original was really different it's now lost.

I'll find a good dump and repeat the process.

Many thx Alfabit :)

[jovime]

Use this one. Cut the pin no.58 on the ecu.
If you will have poor idle afterwards, use Renault Clip to configure it with AC option set to ON.
It is a known bug in software.

Pass in PM.

Where to cut the pin? From connector A or B?

[Dane-Elec]

Where to cut the pin? From connector A or B?
A or B ??
This ecu only have 1 plug, correct?

[alfabit]

Yope! You're right, all dumps start different...

But it does not make sense at all... reading it in boot mode gives you direct access to all flash area, without restrictions. It's the first time that BS does something like this and I'm using it daily for BOOT purposes flawlessly.

Something is strange here. Problem is that I made dump virgin and wrote it to the ECU, so if original was really different it's now lost.

I'll find a good dump and repeat the process.



I think your original dump is not lost, you have it read by byteshooter, write it back to the flash and read the flash again on a proper programmer, you`ll obtain it binary.
Immokiller or Carsoftware work only with binary files, don`t know how to make off or virgin by a dump read with byteshooter

LE : pin 58 is noted on the black connector of the ecu, the second row of pins

[jovime]

A or B ??
This ecu only have 1 plug, correct?

Nope, it has 2 connectors, let me upload some images :)

http://www.digital-kaos.co.uk/forums/attachment.php?attachmentid=105838&stc=1&d=1330417465

[jovime]

I think your original dump is not lost, you have it read by byteshooter, write it back to the flash and read the flash again on a proper programmer, you`ll obtain it binary.
Immokiller or Carsoftware work only with binary files, don`t know how to make off or virgin by a dump read with byteshooter

LE : pin 58 is noted on the black connector of the ecu, the second row of pins

I'll do so today and repost the dump, many thx again ^^

[alfabit]

I'll do so today and repost the dump, many thx again ^^

Glad to be helping you !

[Milkman]

Nevermind...

[jovime]

Hey guys, I have updates.

Tried BS read treated with SCP and it worked. It needs emulator anyways.

Should be a total immo off solution possible? I'm attaching the file I used.

Many thx to all who kindly helped me with this.

BR!

[alfabit]

Hey guys, I have updates.

Tried BS read treated with SCP and it worked. It needs emulator anyways.

Should be a total immo off solution possible? I'm attaching the file I used.

Many thx to all who kindly helped me with this.

BR!

SCP doesn`t know how to do immo off, try i*odecoder, i*otool, i*ocleaner, but if you succeeded with emu i would let him as it is if i were you. No need to bother you more.
Emu is perfect, let it be like this !

[Milkman]

Put this file, cut immo line and that's all.

[thomas76]

Put this file, cut immo line and that's all.

Are you sure without emulator ? It's for 32 or 32N ? Compatible with all motors 1.2 1.4 1.8 ?

Thanks in advance !

[Milkman]

Post here your ori file and i'll try to make-it work without emulator.

[thomas76]

I have 2 ecu :

Sirius 32 => 108189

Sirius 32N => 108190

Thanks !

[Milkman]

Try and report, pls. Pass in pm.

[thomas76]

I want to be sure to result, because i send that to 800km ..... :giveup:

[alfabit]

I want to be sure to result, because i send that to 800km ..... :giveup:

The surest result is virgin + immo, i guarantee you not 800 km sent, but 80.000 km. :bounce:

But do as Milkman said to you, he is one of the best around -here. :proud:

[thomas76]

With this files, i write and i cut pin58 ? car start ? because it's for rallye

[Milkman]

Yes, cut immo line and make sure no one put it back, because ecu will be coded again

[thomas76]

Ok i test and i post result

Thanks !!

[thomas76]

S32N :

2FFF0 to 3FFF0 => 00000000000000000 ?

Ori => FFFFFFFFFFFFFF + Checksum ?

[thomas76]

Try and report, pls. Pass in pm.

Sorry, file off for SIRIUS32N, car not start ... :giveup:

[taxi300]

Sorry, file off for SIRIUS32N, car not start ... :giveup:
hi because your dump for siruis32N is wrong
look at our orig dump
S32N :

2FFF0 to 3FFF0 => 00000000000000000 ? false

Ori => FFFFFFFFFFFFFF + Checksum ?

[taxi300]

Hi guys!

Anyone has an immo off solution for this one?

Renault Clio 1.2 Sirius 32N (NO AIR CONDITIONED) - S110138000B / 8200059086

I've been looking at the forum but all solutions seems to be mainly for 1.4 and 1.6 engines.

I'm attaching original flash read.

Kind regards!
hi
verginise it filling 4000-8000 with FF's and put emulator...

[thomas76]

I think all sirius32 and 32N without emulator engine not start :celticscarf:

[taxi300]

I think all sirius32 and 32N without emulator engine not start :celticscarf:
hi ecu siruis32 No can,you can set immo off without emulator, but with siruis32 with can he put it with emulator

[taxi300]

Hi guys!

Anyone has an immo off solution for this one?

Renault Clio 1.2 Sirius 32N (NO AIR CONDITIONED) - S110138000B / 8200059086

I've been looking at the forum but all solutions seems to be mainly for 1.4 and 1.6 engines.

I'm attaching original flash read.

Kind regards!
hi please i need the same in immo off dump siruis32N (1.2 no air S110138000 B / 8200059086) thanks

[thomas76]

I tried several files but the result is the always similar if you have a good files ( OFF without emulator and no CAN ) I WANT :proud:

[taxi300]

I tried several files but the result is the always similar if you have a good files ( OFF without emulator and no CAN ) I WANT :proud:
hi please how you can distinguish between sirius32 with Can and siruis32 without can thanks

[alfabit]

I tried several files but the result is the always similar if you have a good files ( OFF without emulator and no CAN ) I WANT :proud:

Why people choose the hardest way ( immo off which sometimes works and sometimes not ) and not the surest way ( virg + emu which works always ) ?
For me is impossible to understand this ! I give up !
:giveup:

[mecdoc]

boys would prejudice solution immobilizer off
can you help me
thanks

[Milkman]

Your file 100% off. Try and report, pass in PM.

[mostafa badawi]

boys would prejudice solution immobilizer off
can you help me
thanks
hi
ineed password

[jorge antunes]

http://www.digital-kaos.co.uk/forums/images/icons/icon1.png sirius 32n not can s110138000b immo off help
hi frind you have good dump clio 1.2 sirius 32n s110138000b

tanks

[budG60]

I have programmed an immo off 1.2 8v file in a Sirius 32 and cut pin 58. The car started and everything worked fine for 2 weeks, but now the immo seems to be back again?
Is this possible when pin 58 is cut? If the file was not right I would expect it to fail the first time because pin58 is removed from the ecu.
Any ideas?