PDA

View Full Version : PD rev limiter



azibi130
18th April, 2012, 10:46 AM
anyone knows where is the adress for the rpm limiter in PDs?

i tried all fuel maps, LControl, some other maps that i thought they were limiters, but the rpm still cuts at 5355

spawns3
18th April, 2012, 12:05 PM
anyone knows where is the adress for the rpm limiter in PDs?

i tried all fuel maps, LControl, some other maps that i thought they were limiters, but the rpm still cuts at 5355

In the LC u have the limit at 5355 , u try to raise the IQ on LC ?

Cheers

ecutuners
18th April, 2012, 03:10 PM
In the LC u have the limit at 5355 , u try to raise the IQ on LC ?

Cheers

Yes your correct but you must mod the axis on torque limiter also

spawns3
18th April, 2012, 11:08 PM
Change on LC the rpm and rise the IQ table to the rpm do you want , and then go to the torque limiter and put the same rpm , and do the trick .
This is a example . but if u want u can change also the z-axis and play with the speed to do rpm limiter . For ex. till 140kph rpm cut at 6000, after that u can put the rpm limiter lower .
:wink:

vasco fernandes
19th April, 2012, 02:39 AM
axis Y in LC not is kph !

Is ratio kph/rpm

spawns3
19th April, 2012, 02:58 AM
axis Y in LC not is kph !

Is ratio kph/rpm

Just put the name on the axis for people minimally understand the values of the axis

Check this #post10

http://www.digital-kaos.co.uk/forums/f173/can-somone-help-indentifinng-maps-alh-265921/#post1527238


But thanks anyway.

azibi130
19th April, 2012, 05:12 PM
already found what i wanted, thank's...and LC cuts iq even if u push rpm axis higher (also on torque)...

theres a single magic byte ;-)

2010bastian
28th April, 2012, 08:54 PM
Change on LC the rpm and rise the IQ table to the rpm do you want , and then go to the torque limiter and put the same rpm , and do the trick .
This is a example . but if u want u can change also the z-axis and play with the speed to do rpm limiter . For ex. till 140kph rpm cut at 6000, after that u can put the rpm limiter lower .
:wink:

Can you post adress of the Y axis

spawns3
28th April, 2012, 10:56 PM
Can you post adress of the Y axis


Mate u have no make a new y-axis . with a new factor . And it's 1 byte solution for max rpm limiter ! but first u have to change the the LC and TQL

gzk
2nd May, 2012, 01:12 AM
already found what i wanted, thank's...and LC cuts iq even if u push rpm axis higher (also on torque)...

theres a single magic byte ;-)
could you share information ?

spawns3
2nd May, 2012, 08:50 AM
could you share information ?

Search for 5361 , u will find it ;)

azibi130
2nd May, 2012, 10:15 AM
Search for 5361 , u will find it ;)

wrong....the single it's before duration

spawns3
2nd May, 2012, 10:54 AM
wrong....the single it's before duration

Mate ,

Before tell that the people is wrong , why u don't test the solution i give ? ok ?

daniel guerra
2nd May, 2012, 12:25 PM
Hi Spawns,
5361 is part of the axis on LC map, even if you change it it dosen't do anything.

If it's a single value, it's not a value that makes part of axis.

But this is only my humble opinon.

Regards,

spawns3
2nd May, 2012, 12:51 PM
Hi Spawns,
5361 is part of the axis on LC map, even if you change it it dosen't do anything.

If it's a single value, it's not a value that makes part of axis.

But this is only my humble opinon.

Regards,

Yes i know is a single bite with 5361 value not in axis .

spawns3
2nd May, 2012, 01:09 PM
already found what i wanted, thank's...and LC cuts iq even if u push rpm axis higher (also on torque)...

theres a single magic byte ;-)


You open this topic asking for help , and after u find that u don't want share ur solution ?
Here is my Solution
:wink:

Search for 5361 in 1 block , u only find 2 singles one is axis for LC map . So edit the other one and test and post result.

daniel guerra
2nd May, 2012, 01:43 PM
But the 5361 it's in the axis. How many 5361 are in the dump? 3! (In dumps where you've 2 databanks)

2 of them, are part of the LC axis, the other one it's in the area were it can be touched.

Where is the single value?

I do understand what you're saying, and you're wright! That's the hights number for Rev's if i'm not mistaken.

The question is not so well raised, what azibi meant to ask it's another thing.

That should be: what is making the engine to cut a 5355 Rev's?

This is what Azibi wanted to know.

spawns3
2nd May, 2012, 03:51 PM
But the 5361 it's in the axis. How many 5361 are in the dump? 3! (In dumps where you've 2 databanks)

2 of them, are part of the LC axis, the other one it's in the area were it can be touched.

Where is the single value?

I do understand what you're saying, and you're wright! That's the hights number for Rev's if i'm not mistaken.

The question is not so well raised, what azibi meant to ask it's another thing.

That should be: what is making the engine to cut a 5355 Rev's?

This is what Azibi wanted to know.

So if he only know that single , he can't go more than 5361rpm.And that single he says is not rpm limiter !!

gzk
13th May, 2012, 04:44 AM
So if he only know that single , he can't go more than 5361rpm.And that single he says is not rpm limiter !!

here is the file you ask me

spawns3
14th May, 2012, 04:01 AM
Change this bytes at

XXXXX- 5361 - RPM Limiter
XXXXX - 5300 - BIP shut off

And the Axis on TQL and LC and u be able to make 6000rpm .

gzk
14th May, 2012, 03:57 PM
sorry for my poor english what lc does mean ?

smokey08
14th May, 2012, 04:08 PM
sorry for my poor english what lc does mean ?

Launch Control.

gzk
16th May, 2012, 03:50 PM
Change this bytes at

-6C6C6 - 5361 - RPM Limiter
-5432A - 5300 - BIP shut off

And the Axis on TQL and LC and u be able to make 6000rpm .

work well thanks

spawns3
16th May, 2012, 07:59 PM
welcome mate , and if u put on XXXXX - 5800value , the car go to 6000rpm cutting .

azibi130
16th May, 2012, 08:12 PM
Mate ,

Before tell that the people is wrong , why u don't test the solution i give ? ok ?



i just need to change the single i told to you (before duration maps)...and i have the rpm i want....(off course u have to change LC axis and TL like spawns3 said)

the number is 5300 (ASZ_556)...

spawns3
17th May, 2012, 12:05 AM
i just need to change the single i told to you (before duration maps)...and i have the rpm i want....(off course u have to change LC axis and TL like spawns3 said)

the number is 5300 (ASZ_556)...
Mate that single is BIP OFF not rpm limiter .

gzk
19th May, 2012, 07:31 AM
welcome mate , and if u put on 5432A - 5800value , the car go to 6000rpm cutting .

sorry i don't understand what you want to say can you explain differently
here is a video of our drag fabia tdi with the information you gave me for the limiter
bip 5900 rpm lim 6000
Drag fabia tdi by Gzk/Frd 6000 rpm evo 2 a suivre - YouTube

spawns3
19th May, 2012, 01:53 PM
Mate send that mod file to my email .

mexanico1971
19th May, 2012, 06:50 PM
the cars is stop ! event the tax compression are lower in the new diesel motor, they start to lose seal efficiency at 4500 rpm !
maybe I"m wrong !

gzk
21st May, 2012, 02:32 AM
don't worry the video is a full custom build engine cam head manifold big vnt alky etc.... only for drag racing ...
powerband + 5000rpm run on special diesel
i can't share the file i hope you understand why

spawns3
21st May, 2012, 02:53 AM
Ok mate : ) send the original again to my email , and i will make rpm limiter and the bip off. I ask you for the file , but not with the intuite to check your modes ;) edc15 is a very old ecu and very simple to work . I have the knowledge to do more than 300hp without smoke and maf ON .with a lot of mechanical work.

Cheers

gzk
21st May, 2012, 01:13 PM
Ok mate : ) send the original again to my email , and i will make rpm limiter and the bip off. I ask you for the file , but not with the intuite to check your modes ;) edc15 is a very old ecu and very simple to work . I have the knowledge to do more than 300hp without smoke and maf ON .with a lot of mechanical work.

Cheers
don't worry i don't think you want to leech
mechanical is done
300hp is acheived i think .
i need minor information will send you pm
thanks for all

edc
22nd May, 2012, 09:51 PM
here is the file you ask me

can You post the file again ?