MB w208 eis add key

[Pzolee]

Hi friends.

Please add key dump (nec) EIS 1d69j.

Thanks all.

[smayer]

Hi friends.

Please add key dump (nec) EIS 1d69j.

Thanks all.

Post EIs part number.

[Pzolee]

210 545 02 08

[smayer]

Hi friends.

Please add key dump (nec) EIS 1d69j.

Thanks all.

you keys mate,
enjoy

[Pzolee]

Tested key 5 not working.
Original key working.

After programming keys, ezs not communicating, windows, turn signals etc. not working...please help! what can be the problem?

[smayer]

Tested key 5 not working.
Original key working.

After programming keys, ezs not communicating, windows, turn signals etc. not working...please help! what can be the problem?

The problem is EZS dump, maybe you don't use the right tool to read the MCU, try read again and compare with first read. If you read inboard check soldering. I see you have read with AK Chinese trash, most times AK fu** this MCU, to you and everyone still using this bad tool, never read this MCU like 1d69j, read like 0D69J ( just apply to AK).

[Pzolee]

Ak400 read 1d69j....:-(

Ak400 read 0d69j? This problem???

Ak400 nec ir programmer....(key program)

ETL read and write 1d69j?

[smayer]

Ak400 read 1d69j....:-(

Ak400 read 0d69j? This problem???

Ak400 nec ir programmer....(key program)

ETL read and write 1d69j?

Ak400 read 1D69J but sometimes corrupt the contents.

If you read 1D69J in AK 400 as 0d69J is more secure but not 100% secure.

AK 400 sometimes write keys by IR

ETL original read and write 1D69J without problems, is the best solution to do this work.

[locks85]

Tested key 5 not working.
Original key working.

After programming keys, ezs not communicating, windows, turn signals etc. not working...please help! what can be the problem? Last edited by Pzolee; Today at 01:20 PM.
So original key works but ezs no communication ?
or none of the keys work ?
try checking your soldering , many times car will run but because of bad soldering wipers horn indicators and electric windows wont work .
Regards
locks85

[Pzolee]

Original key start car. Remote control not work.
Add key not work. Original Key SSID not add key SSID....

Soldering...good.
AK400 mcu damage?
other mcu write? eeprom?

[smayer]

the small 2 pin can bus connector is connected?

[Pzolee]

yes.......MCU damage?
add key not work....why?
calculation fault? Or?
Original key start car.

[smayer]

You write a small NEC key?
Have tested by IR if key is OK?
Try another dump in same EIS.

[Pzolee]

No other dump.
AK400 ir read original key : SSID : 9B 28 DF 10
Add key SSID : 10 DF 28 9D key 5.....

SSID wrong? It should be. : 9D 28 DF 10 ?

[smayer]

No other dump.
AK400 ir read original key : SSID : 9B 28 DF 10
Add key SSID : 10 DF 28 9D key 5.....

SSID wrong? It should be. : 9D 28 DF 10 ?

The keys I send to you have SSID 9D 28 DF 10
The SSID is the same just byte swap, your problem is another.

[Pzolee]

Tried another ezs....car work perfectly.

MCU dump damage.

Uploading dumps,please repair friends...

[Pzolee]

210 545 02 08.....or 208 545 02 08 dump.....

[Pzolee]

Other dump....uploading...

Please 2 pieces nec small key calculation...

Thank you.

[bram380]

Other dump....uploading...

Please 2 pieces nec small key calculation...

Thank you.

please ezs type and software version.

[Pzolee]

210 545 02 08. Software version not found.....