PDA

View Full Version : Piasini locked



tehnosoftex
27th August, 2012, 05:16 PM
Hi, I just buy a china clone from piasini. I Get the licence and all ok. Today I connect it on a car and did not pay attention on the internet. I forgot the internet on and now I get this message on piasini.
Can anyone knows how to solve it?
Thank you
Sorin

blackpirate
27th August, 2012, 05:21 PM
get a new license! and test! i suggest turn off internet or use a firewall.

tehnosoftex
27th August, 2012, 05:36 PM
Is not a software problem, it is a hardware one. I installon other laptop and same message. Even in slave mode I have same message. I think may be some thing has been updated and corupt some thing in hardware. May be eeprom 93c46 from ftdi, or the flash from mcu or the serial flash. May be some one has a solution

blackpirate
27th August, 2012, 05:54 PM
hmm..srry......

ecutuners
27th August, 2012, 07:33 PM
You need the dump from mcu and a beeprog to flash it :)

tehnosoftex
27th August, 2012, 09:25 PM
I have beeprog, need only the dump

zecas
27th August, 2012, 10:48 PM
all wrongs

just program M25P32 with upa and all ok

ecutuners
27th August, 2012, 11:01 PM
Dump here for repair

camil
27th August, 2012, 11:16 PM
Dump here for repair

Facts and not only words, well done mate ;)

eprommazza
27th August, 2012, 11:34 PM
want only advise ...also without repair piasini work perfect

work again

br

eugen8
28th August, 2012, 12:09 AM
Hi, I just buy a china clone from piasini. I Get the licence and all ok. Today I conect it on a car and did not pay atention on the enternet. I forgot the internet on and now I get this message on piasini.
Can anyone knows how to solve it?
Thank you
Sorin
For me it works perfect even with this message...you don't need to pay atention

Novik_UA
28th August, 2012, 01:13 PM
Have same trouble here (http://http://www.digital-kaos.co.uk/forums/f173/piasini-keygen-276881/index9.html#post1653279) , and like eprommazza (http://www.digital-kaos.co.uk/forums/members/88361-eprommazza/) say,I try it in work, and is working good :celticparty:
http://s49.radikal.ru/i124/1208/ba/c71c182dca8ft.jpg (http://radikal.ru/F/s49.radikal.ru/i124/1208/ba/c71c182dca8f.jpg.html)

eprommazza
29th August, 2012, 04:31 PM
all wrongs

just program M25P32 with upa and all ok

Hi, i have programmed m25p32 with upa select m25p20 setting 3,3v

all ok but after i try have same problem license ...

i have disconnected internet first ...

solution not good for me

best regards

tehnosoftex
29th August, 2012, 06:29 PM
Ive programed 25p32 with beeprog and now I have odd name and company name but in rest seem to be ok. I did not connect to internet but did not make any test on ecu. The original dump was 4Mb and not only 2.25K. It has some more data and not only ff besyde the first 2.25k. May be when you program as 25p20 that data which remains contain the fake info. I make all dump ff but the first 2.25k. Please Eprommazza can you provide the picture for connect dcu3r ecu on boot mode, I have it and can make tests on it.
Thank you

tehnosoftex
30th August, 2012, 07:51 PM
Some bad news. I try today to read a siemens ecu sirius81 from citroen c5 2l mpi. I connect in boot mode and read the flash. After that I remove the flash and read it with beeprog. I know that for siemens ecus when it is read with programmer it needs some changes , and I make these changes with winols. This is what Ive got.

eprommazza
30th August, 2012, 11:32 PM
Some bad news. I try today to read a siemens ecu sirius81 from citroen c5 2l mpi. I connect in boot mode and read the flash. After that I remove the flash and read it with beeprog. I know that for siemens ecus when it is read with programmer it needs some changes , and I make these changes with winols. This is what Ive got.

reading piasini not good i see but this depending of various cases

piasini can read ok this ecu only you need try better do boot mode

your interface sure are ok 100% don t worry


best regards

eprommazza
30th August, 2012, 11:59 PM
piasini can read/write all ecu with mcu ST10_C167 all flash 29fxxx

:beerglass:

tehnosoftex
31st August, 2012, 10:18 AM
I know that must read all ecus with c16x and st10 but I did not know what I do wrong. I ve tried all 29f400 modes from piasini menu and same reading. I read in a chiptuning forum a post from Cristian Piasini in which he said that he has a lot of surprises for clone users. I begin to think that this is one of them. I will try other ecus and report the findings.

eprommazza
31st August, 2012, 10:26 AM
I know that must read all ecus with c16x and st10 but I did not know what I do wrong. I ve tried all 29f400 modes from piasini menu and same reading. I read in a chiptuning forum a post from Cristian Piasini in which he said that he has a lot of surprises for clone users. I begin to think that this is one of them. I will try other ecus and report the findings.

can send me image your ecu and how you do boot mode this ecu?
think problem is boot mode ...because i test my piasini work also if have problem license corruption
if use piasini without internet connection cristian can t do nothing ;)


best regards

tehnosoftex
31st August, 2012, 11:24 AM
I choose from autodata citroen c5 2002 mpi 2 L sirius81 and I connect:
from connector c
h4,g4 GND
B4 K line
C3 +12V
from connector B
G4 +12V
From connector A
F2,F3, E3 +12V
The boot pin I connect to the blue whire from piasini
Thank you for your help

eprommazza
31st August, 2012, 12:25 PM
I choose from autodata citroen c5 2002 mpi 2 L sirius81 and I connect:
from connector c
h4,g4 GND
B4 K line
C3 +12V
from connector B
G4 +12V
From connector A
F2,F3, E3 +12V
The boot pin I connect to the blue whire from piasini
Thank you for your help

after boot mode you disconnect this pin of boot or no?
connection for power sure not are problem
problem can do gnd boot mode pointer or other maybe also need to try with resistor
you can also try do boot mode pin 28 flash,
remember after ecu is in boot mode need disconnect wire from boot.
this only few advise for you !!report me if you success..
need do any test

datapage
31st August, 2012, 12:42 PM
SOME Programmers, KESS, GALETTO, PIASINI ETC SOME ECU LEER PARTIAL MODE.
READ FULL BEE PROG immobilizer and injection INSIDE A FLASH FOR EXAMPLE.
4BV = ST10F READ FULL = ST10F = 1400K.
KESS: BLOCK 10, READ ONLY 4BV injection.
NO NEED TO COMPLETE PICTURE OF MEMORY OF SERVICE DEPENDS.
SIRIUS 32 BeeProg READ TOTAL (IMMOBILIZER injection).
SIRIUS 32 PIASINI , KESS, READ PART 256K (FFFFFFFF injection).
WHEN YOU NEED TOTAL FILE, USE IN MEMORIES BeeProg SUPPORTED.
BeeProg = FULL MEMORY
ST10F = FULL MEMORY
KESS = PARTIAL
GALETTO = PARTIAL
PIASINI = PARTIAL
ETC ...

eprommazza
31st August, 2012, 12:46 PM
SOME Programmers, KESS, GALETTO, PIASINI ETC SOME ECU LEER PARTIAL MODE.
READ FULL BEE PROG immobilizer and injection INSIDE A FLASH FOR EXAMPLE.
4BV = ST10F READ FULL = ST10F = 1400K.
KESS: BLOCK 10, READ ONLY 4BV injection.
NO NEED TO COMPLETE PICTURE OF MEMORY OF SERVICE DEPENDS.
SIRIUS 32 BeeProg READ TOTAL (IMMOBILIZER injection).
SIRIUS 32 PIASINI , KESS, READ PART 256K (FFFFFFFF injection).
WHEN YOU NEED TOTAL FILE, USE IN MEMORIES BeeProg SUPPORTED.
BeeProg = FULL MEMORY
ST10F = FULL MEMORY
KESS = PARTIAL
GALETTO = PARTIAL
PIASINI = PARTIAL
ETC ...

we agree with you but this has nothing to do what we are saying here
slightly off topic

tehnosoftex
31st August, 2012, 04:46 PM
after boot mode you disconnect this pin of boot or no?
connection for power sure not are problem
problem can do gnd boot mode pointer or other maybe
also need to try with resistor
you can also try do boot mode pin 28 flash,
remember after ecu is in boot mode need disconnect wire from boot.
this only few advise for you !!report me if you success..
need do any test
Success, you were right, I did not disconect boot pin after id ecu and thats why I read wrong. The boot pin is as you say also at pin 28 from flash, and pin 28 is DQ6 and thats why always the bit 6 was 0. Thank you Eprommazza for your help.
I did not read before any ecu in boot mode, and did not know that I must disconect boot pin, may be it will be good that the blue pin from piasini has to be disconnected automaticaly.
Now because I succeed I can go further and test bdm connection from piasini, I am not sure about bdm pins from piasini but I am willing to try it, and I have several edc16 ecus. I will report my findings
Sorin

eprommazza
31st August, 2012, 04:47 PM
Success, you were right, I did not disconect boot pin after id ecu and thats why I read wrong. The boot pin is as you say also at pin 28 from flash, and pin 28 is DQ6 and thats why always the bit 6 was 0. Thank you Eprommazza for your help.
I did not read before any ecu in boot mode, and did not know that I must disconect boot pin, may be it will be good that the blue pin from piasini has to be disconnected automaticaly.
Sorin

no problem friend!!!
i am good tecnik!!
i am happy for you

zanovo
19th September, 2012, 09:38 AM
all wrongs

just program M25P32 with upa and all ok

M25P32 - it must be SPI eeprom, but I fined only ATMLH00846D n Piasini bard.... and it lks like MW eeprom Pin5-GND, Pin8-Pwer.
It`s another tipe of board ?
I fined 25P32 on the board and kill it in attempts reading with 5V..... than see datasheet with instructions about 3V. Place an order - 5 pcs W25X32 on ebay.....

zecas
19th September, 2012, 09:33 PM
M25P32 - it must be SPI eeprom, but I fined only ATMLH00846D n Piasini bard.... and it lks like MW eeprom Pin5-GND, Pin8-Pwer.
It`s another tipe of board ?
I fined 25P32 on the board and kill it in attempts reading with 5V..... than see datasheet with instructions about 3V. Place an order - 5 pcs W25X32 on ebay.....

you can buy also in farnell
program off board, i had to improvise an adapter.

zanovo
19th September, 2012, 10:30 PM
Farnell is good store, but I must order no less 20euro... I buy 5 pcs W25X32 for 13$ on Ebay.
What programmer are you use for M25P32 ?
Can you show adapter schematics ?
I try with UPA as 25C320 and then with Beeprog using ISP connection.

tehnosoftex
21st September, 2012, 08:23 AM
Farnell is good store, but I must order no less 20euro... I buy 5 pcs W25X32 for 13$ on Ebay.
What programmer are you use for M25P32 ?
Can you show adapter schematics ?
I try with UPA as 25C320 and then with Beeprog using ISP connection.
I use beeprog with socket adapter no isp, but I think that can work also on ISP

zanovo
22nd September, 2012, 11:54 AM
Can you post foto of adapter for BeeProg or pinout ?
I have Beeprog, but haven`t adapter for M25P32 Flash.

tehnosoftex
25th September, 2012, 10:33 AM
There is only 8 pins there is no need for any adapter, only a socket to solder the memory and to insert in zif socket of beeprog. Pin 1 of memory must be on pin 1 of beeprog s.o.

niwat_spp
14th October, 2012, 10:45 AM
which's m25p32 chip? my tool problem same. Please help me

thank in advance

Holtek
14th October, 2012, 03:02 PM
See the picture below:

niwat_spp
14th October, 2012, 03:41 PM
See the picture below:
thank holtek I will try program to it for repair my tool

niwat_spp
17th October, 2012, 01:13 PM
Hi. after I dump m25p32. Problem it still not work. How to solve it.:(

thank in advance

tec.guilherme
20th October, 2012, 04:57 AM
Hello I have solution send in PM the email I send the fixer for this one.

Thanks.

niwat_spp
21st October, 2012, 03:18 PM
Hello I have solution send in PM the email I send the fixer for this one.

Thanks.
thank a lot friends. my tool it solved.:party:

Chip Tuner
22nd December, 2012, 10:06 PM
Who can count the CRC the car Honda Accord with power Misuhita

jolidj
27th December, 2012, 03:56 PM
post solution please.

maglaras
24th January, 2013, 05:14 PM
did anyone have so;ution for this peoblem

maglaras
7th February, 2013, 03:36 PM
how can i read and rite this eeprom in upa o dont have it on the list only 25p020 and 25p040

stilotto
28th March, 2013, 04:07 PM
Hello I have solution send in PM the email I send the fixer for this one.

Thanks.

Please can you help me i have the same problem!
Thanks

faberecu66
20th June, 2013, 07:13 PM
Is possible read and write correct with upa ??? and were , 25cxx connector or m35o80 connector? or upa not make read right

garagetech
22nd January, 2014, 09:46 PM
Please can you help me i have the same problem!

chipauto
28th January, 2014, 02:26 PM
read microchem
i help you

jset
23rd May, 2014, 09:06 AM
hello
does any one have a connection to read 25P32

thanks

tehnosoftex
24th May, 2014, 04:29 PM
What connections do you need, it has only 8 pins

prusony
24th May, 2014, 04:38 PM
hello
does any one have a connection to read 25P32

thanks

Better desold chip and read with programmator, example Beeprog......