View Full Version : Micronas xprog Touran 04 need help connection
ana_11
3rd September, 2012, 04:11 PM
Hello
I try read flash in xprog but not positive result,
please worked connection.
Thx
solitaire
3rd September, 2012, 07:10 PM
from xprog manual
ana_11
3rd September, 2012, 07:30 PM
This is not this board, but i try and not work ;(.
elservis
3rd September, 2012, 07:43 PM
Km are in eeprom 24c16 or 24C32. You dont need read micronas, only eeprom 24CXX.This dash you can do very easu via OBD.
Sorry my mistake,now I see you need read flash.
verica
3rd September, 2012, 07:59 PM
you can change km only with 24c32 can you tell me how please
ana_11
3rd September, 2012, 08:13 PM
I need program key, original dash damage and need read
this micronas to program key in tango.
lupu_sandu
3rd September, 2012, 09:14 PM
You solder red wire from coaxial in wrong position i see.
ana_11
3rd September, 2012, 09:23 PM
coaxialis connected to pin 15 mcu, low quality photo ;(.
i don't know where is fault, i need read mcu, in obd
no read if immo active.
lupu_sandu
3rd September, 2012, 09:37 PM
Try to connect as here.
1-white TMS
2-orange TCK
3-yellow TDI
4-gray TD0
5-black (coxial gnd) GND
6-green TEST
7-blue RST
8-coxial XTAL
9-red VCC
lupu_sandu
3rd September, 2012, 09:38 PM
You can try to put in service mode, and then you can read via obd2.
exe123
3rd September, 2012, 11:09 PM
Touran from 2004 can be done even with can commander clone. no need for service, no need for xprog. everything possible via obd.
robert54
3rd September, 2012, 11:21 PM
Milleage in micronas is from 2006 before only eeprom.
lupu_sandu
4th September, 2012, 08:14 AM
Damn, i now see year of the car.
ana_11
4th September, 2012, 12:34 PM
Touran from 2004 can be done even with can commander clone. no need for service, no need for xprog. everything possible via obd.
You right, i read immo in carprog. i have pin and 7th byte
but time lock on dash, waiting 30min and still locked.
ana_11
4th September, 2012, 06:45 PM
Ok i program key in Keymaker. Need help to swap ecu edc16u1.
i change ecu original is by tuning and corrupt, try copy pin, and component number. In ecu no fault, but if try adapt to channel
50 a have Checksum not ok ;(.
in log immo:
17:15:30 Group 001: Immobilizer I
No Engine Start permitted
Yes Engine (ECU) responds
Yes Key Status OK
2.0 Number of adapted Keys
17:15:30 Group 002: Immobilizer II
Yes Variable Code authorized
Yes Key Status (Transponder Lock)
Yes Fixed Code authorized
6.0 Immobilizer Status
17:15:30 Group 003: Immobilizer III (Lock Time)
0.0 Login-Lock Tester
0.0 Login-Lock CAN-Bus
0.0 Lock Scan Protection
1.0 Status Immo-LED
i post my file, maybe any suggest ?
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.