Cummins Fault Code 2559

[mathura]

I am getting fault code 2559 on Cummins ISBe engine mounted in DAF LF45 but there is no troubleshooting steps for this code.
Can someone advise how I can get the troubleshooting guide for this code.

The engine starts and runs for 30 seconds and then die and the fault 2559 is shown as inactive but the count rises every time you start and engine dies.

Thanks for any help

[kitty-hawk]

Hello,

Have you engine serial number ?
I found this :

[mathura]

Hello,

Have you engine serial number ?
I found this :


Thank you very much for this quick response. It therefore means that the ECM has to be reflashed, am I correct.

Engine SN: 21527393
CM 800

Thanks for Calibration File

[integlikewhoa]

Thank you very much for this quick response. It therefore means that the ECM has to be reflashed, am I correct.

Engine SN: 21527393
CM 800

Thanks for Calibration File

So did you get everything you need to fix it?

[mathura]

So did you get everything you need to fix it?

No I need calibration file for ESN 21527393

Thanks

[kitty-hawk]

For download calibration i need ecm code. (number of calibration)

[mathura]

For download calibration i need ecm code. (number of calibration)

Thanks
I will have to go back to job site to get information

[kitty-hawk]

You did not make a recording with Insite ?

[mathura]

You did not make a recording with Insite ?

No I did not but will get the info soon.
Did you ever had this probelm before because the truck parked for two days and when try starting this issue came up. Had other issues with sensor harness before which was corrected.

Thanks again

[kitty-hawk]

No my friend, I never had this problem.

[nikola_janev]

Engine SN: 21527393
CM 800

I will see

[mathura]

For download calibration i need ecm code. (number of calibration)

I managed to get get customer to bring the truck to the shop today.

I really need the Cal File to try and see what happens

Here is the information

Engine SN: 21527393
ECM SN: 83907108
ECM Code: T90099.04
Cal Software Phase: 01050605


Hope this information is adequate

Thanks

[mang5087]

I managed to get get customer to bring the truck to the shop today.

I really need the Cal File to try and see what happens

Here is the information

Engine SN: 21527393
ECM SN: 83907108
ECM Code: T90099.04
Cal Software Phase: 01050605


Hope this information is adequate

Thanks
hope this helps. thanks

[mathura]

hope this helps. thanks

Thank you so much Mang for you quick respone. I will try installing cal file and let you know how it goes

[mathura]

NEED HELP
I tried installing Cal File in ECM but Insite is giving me this message

"INSITE could not detect calibration for the selected ECM"

These are the steps I went through please advise if I am doing something wrong
1.I installed the file in calibration workspace
2.I connect to ECM and opened calibration selection
3.A red dot was shown next to calibration workspace
4.I clicked on it and a drop down box opened, then I clicked on automotive
5. The cal file appeared yellow in colour
6.When I clicked on the cal file then I get the above message in the right hand column

What am I doing wrong please advise

Thanks

[kitty-hawk]

Can you see T90099.10 ?

https://rapidshare.com/files/778170609/Capture.GIF

[mathura]

Can you see T90099.10 ?

https://rapidshare.com/files/778170609/Capture.GIF


I have only one Cal File in workstation for the isbe

I cannot see the T90099 as shown on your picture

[mang5087]

I have only one Cal File in workstation for the isbe

I cannot see the T90099 as shown on your picture

make sure in C:\Intelect\INSITE\CalibrationWorkspace

hope this helps thanks

[mathura]

make sure in C:\Intelect\INSITE\CalibrationWorkspace

hope this helps thanks

very positive about this my friend or else I would not have seen the cal file displayed

[kitty-hawk]

Run insite and go to :

(screen 1) Tools => Options, then go to :

(screen 2) "extraction data"

(screen 3) and puts everything in the right column. press ok.

Sorry for the screen but my insite is in french

https://rapidshare.com/files/469943915/Screens.rar

[mathura]

I understand from Mang that the cal file is the probelm, could someone please post a new file

Here is the information

Engine SN: 21527393
ECM SN: 83907108
ECM Code: T90099.04
Cal Software Phase: 01050605

Thanks

[kitty-hawk]

I understand from Mang that the cal file is the probelm, could someone please post a new file

Here is the information

Engine SN: 21527393
ECM SN: 83907108
ECM Code: T90099.04
Cal Software Phase: 01050605

Thanks

you must have only one calibration in file "CalibrationWorkspace" and you must to put the unzipped folder "INTELECT" whole.
I think calibration of mang is good.

[mathura]

you must have only one calibration in file "CalibrationWorkspace" and you must to put the unzipped folder "INTELECT" whole.
I think calibration of mang is good.

OK Mang gave me some instructions and I can now see the cal file in the right column.

He told me to right click on it and move it to the right hand column

Thanks to all who has helped, I will try to calibrate ECM as soon as I have the time will let you know the results

[mathura]

PROBELM SOLVED

Hello Friends just want to let you know that I installed Cal File sucessfully and the probelm is now solved.

Thanks to all who helped especially Mang and Kitty Hawk

[SKODANIKOV]

Hi friends i have the same problem with Daf LF45 code error 2559. When engine run after 10 sec. show message Engine Warning and engine shutdown.
ESN:21489321
P/N:4898112
S/N:83894813
E/C:T90100.00
SC97163
Bosch number:0281010254
Can you help me with original flash?