View Full Version : Cummins Fault Code 2559
mathura
1st October, 2012, 02:54 PM
I am getting fault code 2559 on Cummins ISBe engine mounted in DAF LF45 but there is no troubleshooting steps for this code.
Can someone advise how I can get the troubleshooting guide for this code.
The engine starts and runs for 30 seconds and then die and the fault 2559 is shown as inactive but the count rises every time you start and engine dies.
Thanks for any help
kitty-hawk
1st October, 2012, 04:30 PM
Hello,
Have you engine serial number ?
I found this :
mathura
1st October, 2012, 05:00 PM
Hello,
Have you engine serial number ?
I found this :
Thank you very much for this quick response. It therefore means that the ECM has to be reflashed, am I correct.
Engine SN: 21527393
CM 800
Thanks for Calibration File
integlikewhoa
1st October, 2012, 05:09 PM
Thank you very much for this quick response. It therefore means that the ECM has to be reflashed, am I correct.
Engine SN: 21527393
CM 800
Thanks for Calibration File
So did you get everything you need to fix it?
mathura
1st October, 2012, 05:20 PM
So did you get everything you need to fix it?
No I need calibration file for ESN 21527393
Thanks
kitty-hawk
1st October, 2012, 05:31 PM
For download calibration i need ecm code. (number of calibration)
mathura
1st October, 2012, 06:44 PM
For download calibration i need ecm code. (number of calibration)
Thanks
I will have to go back to job site to get information
kitty-hawk
1st October, 2012, 07:00 PM
You did not make a recording with Insite ?
mathura
1st October, 2012, 08:04 PM
You did not make a recording with Insite ?
No I did not but will get the info soon.
Did you ever had this probelm before because the truck parked for two days and when try starting this issue came up. Had other issues with sensor harness before which was corrected.
Thanks again
kitty-hawk
1st October, 2012, 08:22 PM
No my friend, I never had this problem.
nikola_janev
2nd October, 2012, 10:07 PM
Engine SN: 21527393
CM 800
I will see
mathura
24th October, 2012, 07:07 PM
For download calibration i need ecm code. (number of calibration)
I managed to get get customer to bring the truck to the shop today.
I really need the Cal File to try and see what happens
Here is the information
Engine SN: 21527393
ECM SN: 83907108
ECM Code: T90099.04
Cal Software Phase: 01050605
Hope this information is adequate
Thanks
mang5087
24th October, 2012, 10:46 PM
I managed to get get customer to bring the truck to the shop today.
I really need the Cal File to try and see what happens
Here is the information
Engine SN: 21527393
ECM SN: 83907108
ECM Code: T90099.04
Cal Software Phase: 01050605
Hope this information is adequate
Thanks
hope this helps. thanks
mathura
25th October, 2012, 12:45 PM
hope this helps. thanks
Thank you so much Mang for you quick respone. I will try installing cal file and let you know how it goes
mathura
25th October, 2012, 04:25 PM
NEED HELP
I tried installing Cal File in ECM but Insite is giving me this message
"INSITE could not detect calibration for the selected ECM"
These are the steps I went through please advise if I am doing something wrong
1.I installed the file in calibration workspace
2.I connect to ECM and opened calibration selection
3.A red dot was shown next to calibration workspace
4.I clicked on it and a drop down box opened, then I clicked on automotive
5. The cal file appeared yellow in colour
6.When I clicked on the cal file then I get the above message in the right hand column
What am I doing wrong please advise
Thanks
kitty-hawk
25th October, 2012, 05:12 PM
Can you see T90099.10 ?
https://rapidshare.com/files/778170609/Capture.GIF
mathura
25th October, 2012, 09:25 PM
Can you see T90099.10 ?
https://rapidshare.com/files/778170609/Capture.GIF
I have only one Cal File in workstation for the isbe
I cannot see the T90099 as shown on your picture
mang5087
25th October, 2012, 11:03 PM
I have only one Cal File in workstation for the isbe
I cannot see the T90099 as shown on your picture
make sure in C:\Intelect\INSITE\CalibrationWorkspace
hope this helps thanks
mathura
25th October, 2012, 11:42 PM
make sure in C:\Intelect\INSITE\CalibrationWorkspace
hope this helps thanks
very positive about this my friend or else I would not have seen the cal file displayed
kitty-hawk
26th October, 2012, 02:42 PM
Run insite and go to :
(screen 1) Tools => Options, then go to :
(screen 2) "extraction data"
(screen 3) and puts everything in the right column. press ok.
Sorry for the screen but my insite is in french
https://rapidshare.com/files/469943915/Screens.rar
mathura
26th October, 2012, 09:48 PM
I understand from Mang that the cal file is the probelm, could someone please post a new file
Here is the information
Engine SN: 21527393
ECM SN: 83907108
ECM Code: T90099.04
Cal Software Phase: 01050605
Thanks
kitty-hawk
27th October, 2012, 09:32 AM
I understand from Mang that the cal file is the probelm, could someone please post a new file
Here is the information
Engine SN: 21527393
ECM SN: 83907108
ECM Code: T90099.04
Cal Software Phase: 01050605
Thanks
you must have only one calibration in file "CalibrationWorkspace" and you must to put the unzipped folder "INTELECT" whole.
I think calibration of mang is good.
mathura
27th October, 2012, 01:28 PM
you must have only one calibration in file "CalibrationWorkspace" and you must to put the unzipped folder "INTELECT" whole.
I think calibration of mang is good.
OK Mang gave me some instructions and I can now see the cal file in the right column.
He told me to right click on it and move it to the right hand column
Thanks to all who has helped, I will try to calibrate ECM as soon as I have the time will let you know the results
mathura
30th October, 2012, 04:29 PM
PROBELM SOLVED
Hello Friends just want to let you know that I installed Cal File sucessfully and the probelm is now solved.
Thanks to all who helped especially Mang and Kitty Hawk
SKODANIKOV
22nd February, 2020, 01:39 PM
Hi friends i have the same problem with Daf LF45 code error 2559. When engine run after 10 sec. show message Engine Warning and engine shutdown.
ESN:21489321
P/N:4898112
S/N:83894813
E/C:T90100.00
SC97163
Bosch number:0281010254
Can you help me with original flash?
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.