View Full Version : Iveco Eurocargo - VCM modul by WABCO
szkeptmen
10th October, 2012, 09:20 PM
Hi,
Can somebody help me to find immo code from dump ?
Iveco Eurocargo, year 2008, has no immobox.
Only VCM modul, made by Wabco, inside 95320 eeprom.
Lost key problem... :(
Thanks in advance, szkeptmen
keygargoil
10th October, 2012, 09:47 PM
Hi,
Can somebody help me to find immo code from dump ?
Iveco Eurocargo, year 2008, has no immobox.
Only VCM modul, made by Wabco, inside 95320 eeprom.
Lost key problem... :(
Thanks in advance, szkeptmen
this should have either a small black immo box near the left of the column or bsi side of glove box
szkeptmen
10th October, 2012, 10:51 PM
this should have either a small black immo box near the left of the column or bsi side of glove box
No, it hasn't these boxes.
The immo reader coil goes directly to this VCM modul.
No immobox, no BSI, the OBD connector wires from this modul !!! ( I know the older Iveco trucks.)
I never seen it before. :(
keygargoil
11th October, 2012, 11:30 PM
Hi,
Can somebody help me to find immo code from dump ?
Iveco Eurocargo, year 2008, has no immobox.
Only VCM modul, made by Wabco, inside 95320 eeprom.
Lost key problem... :(
Thanks in advance, szkeptmen
do you have a picture of it
szkeptmen
12th October, 2012, 12:13 AM
do you have a picture of it
Of course...
szkeptmen
12th October, 2012, 09:05 PM
Nobody can help me ?
This truck from year 2008... not too new, I think.
keygargoil
13th October, 2012, 01:52 AM
what id is your key is it from the dealer
szkeptmen
14th October, 2012, 11:55 PM
what id is your key is it from the dealer
Key ID48 (Magic II)
The dealer asks 230 euro for the keycard only !
(mechanical/key cutting and an immo code)
Very expensive... :( only card...
greyg
16th October, 2012, 03:25 PM
Send me VIN on PW.
keygargoil
17th October, 2012, 10:07 PM
Key ID48 (Magic II)
The dealer asks 230 euro for the keycard only !
(mechanical/key cutting and an immo code)
Very expensive... :( only card...
did you get the pin code for it looking through your dump there are a few possible pin codes
twalters
14th June, 2017, 05:54 PM
I have also wabco unit
The key reader goes to bsi and 24c256 big eep.
In wabco is 25lc640.
I'm not completely sure what I need to read. Dealer key I'm told is id62. 2007 iveco euro cargo but newer model than 2001 to 2007. Any help? Thanks.
doolittle
14th June, 2017, 10:43 PM
Read the 25lc640 and use a original dealer key. Tango has the key maker
ecuremap1
12th August, 2017, 01:43 PM
Read the 25lc640 and use a original dealer key. Tango has the key maker
can be used key or not?
kredka74
20th August, 2017, 06:15 PM
Hi!
I have similar problem, Iveco Wabco vcm, truck cranking, but not start, fault in vcm B9 -immo or component faulty, truck start on emergency pin code.
I check the key by Tango its ok ( Tango give me the pin code), VCM sending reading frame to transponder antena as well. Its that truck loose synchro between vcm and engine ecu? There are no CAN Bus faults.
Regards:
Bob
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.