help C5 2.2 hdi EGR off

[mexanico1971]

hi !
can someone please switch egr off in this file ?!
or tell me witch address and value should I change !

thank"s in advance !

BR

this is the file that was in the car !

[mexanico1971]

I think is the same of the 2.0 hdi !
I done it by hand later the car cames and I gonna to tested

[avtonega]

passssssss pm.

[mexanico1971]

passssssss pm.

hi !
Thank"s but the car do not start !
in winols 1.5 the cks blocks can not be identified 61000-6BCFB
and 71000-7BCFB

winols say that in this areas no change should be applied !
what do I have to do ?!

BR

[mexanico1971]

Hi again !
this car is automatic gear , I found a ori map but don"t know if is automatic gear !
is there a lot of differences in the maps ?!
I do not have shore because the file that was in the car was mod and I compared width the ori I find and it got a lot of diferences !

I gonna left the ori and find , could some one compare width the one that the car have and see if is not corrupted ?!

thank"s in advance !
PS: if is important this car run also at HHO for 2 months and the egr is ruined that"s why I want to switch it off ! because always give the boost pressure overload DTC

[mexanico1971]

Ok !
this kind of thing"s only append to me !
the guy from the garage that remap the car and make FAP of, put another file width different number"s !
the original file from the ecu is this one


can someone please kill the EGR in this file !

thank"s in advance

regards

[taxi300]

Ok !
this kind of thing"s only append to me !
the guy from the garage that remap the car and make FAP of, put another file width different number"s !
the original file from the ecu is this one


can someone please kill the EGR in this file !

thank"s in advance

regards

hi here is your flash ecu with egr off
explication:
please go to 6111E, 16 Bit is set, the single activation or deactivation of the EGR is in the first value "00256" just after 00015
Then spend 8 Bit, what we give "000" "001".
To disable the EGR pass "1" to "0" which is "000" "000".
Given 16-bit start value "256" becomes "000"
thanks

[mexanico1971]

Hi !
this car is freaking me out !
the falling DTC"s still append !

P0245 boost
P0235 map malfuncion and boost sensor
P0402 EGR

and this two that I do not know what it is

CVA -P1797 and suspension P08D1

in ESP there is no communication width the ecu !

any one have one situation like this one ?!

BR

[antibisic]

Hi !
this car is freaking me out !
the falling DTC"s still append !

P0245 boost
P0235 map malfuncion and boost sensor
P0402 EGR

and this two that I do not know what it is

CVA -P1797 and suspension P08D1

in ESP there is no communication width the ecu !

any one have one situation like this one ?!

BR

I think that your file is edited before and fap disabled example with ecusafe that,s why you get problem with boost ,for ESP this fault is here because of time when your car not started cause bad checksumm and esp don,t see ecu

[mexanico1971]

so do I need a original file to star from the beginning !

does anyone have one for automatic gear width this numbers ?!
0281010855-1037353784
this are the numbers that are in the ecu

thank"s

[mexanico1971]

ok ! problem solved ! I made egr and dpf of by hand and closed the egr pipe !
now the car runs good again !
My thank"s to taxi300 and antibisic and avtonega for the help !

regards

[diagmanager]

1 byte swithced egr