PCR2.1

[rj22]

Hello

where the point boot mode in the driver Continental SIMOS PCR2.1 5WP42876 AA

through

[rappttor]

and you will use what tool to read it?

[rj22]

galletto my friend

[correcaminos]

galletto my friend

not only one.

100ohm, 1kohm and another 1kohm resistor making bridges between some pads.

[xtreem]

galletto my friend


witch galletto? ori iur clone??

[xtreem]

galletto my friend

cloque work?

[rj22]

work perfect

[xtreem]

you have a schematic for this ecu?
schematic and resistores and pinout.
send me please

[asman2vw]

I have atached pics and instructions for simos .
I hope it helps

[rj22]

just ran out trying to read the ecu

[xtreem]

just ran out trying to read the ecu

Can not you read?
this ecu not need wire boot?

what was the diagram that you used to connect?

can l . can H. 12v. gnd. only?

thanks

[xtreem]

just ran out trying to read the ecu



wat galletto you have? clone?
my is silver box.

[sito]

First of thanks.
I've understood correctly v2 China Galletto:
1 conect the resistors
2 Select Driver
3 Tricore SAK 1796

and read

I will test today

Thanks from Germany

sito

[chli1976]

First of thanks.
I've understood correctly v2 China Galletto:
1 conect the resistors
2 Select Driver
3 Tricore SAK 1796

and read

I will test today

Thanks from Germany

sito

Post results

[filecloud]

just ran out trying to read the ecu

Please post the files you read out...

[pikus_m]

In attechment....

[Catalin_TCM]

galletto 2 clone read/write vag 1.6tdi ???

[mbtun]

nu citeste desigur

[sito]

I tested today but no chance its impossible read by clone

[mexanico1971]

it"s a tc1796 isin"t ?! maybe it"s possible !

[sito]

Who - Wie - como ???????????

possible !!!!

[sito]

and my next problem is Volvo XC60 D4 2.0

inside is EDC 17CP48 impossible to read by Galleto V2

[sito]

My last session with Galletto V2 3 LED

see Pic.

[mislav88]

why are you trying to read PCR with this clone? i advise you to stop trying that unless you want to buy new ecu from dealer, no cheap BDM cloning on used ECU here in case if anything goes wrong.

[auto coding]

My last session with Galletto V2 3 LED

see Pic.

u have problem on making tricore in boot mode....

[sito]

I think the problem ist the Firmware bcause i can read a little. see the pics

[asman2vw]

Are you sure you use the right driver for this ecu ?
09/12Simos PCR2.1 VAG 1.6 TDI Unlock Boot Tool09/12Serial driver Simos PCR2.1 VAG 1.6 TDI

BR

[sito]

I tested by Galletto V2 3LED 0084 - 0103

i think i dont have the Driver, and i have tested

with TOOL PASSWORD TPROT V08 VAG.

thanks

[powertdi]

Ofcourse You havent m8! YOu must be joking for everyone.
Read This ECU Possible only with September 2012 update But you sw is 2011 I sugess.
I saw you have Jtag unlock for reading. Did you tested on Denso? :celtictop::celtictop::celtictop:

[javilette]

this is for read by bdm and obd in the original galletto (i dont khow if posible read and write by obd i dont try) i have one vw caddy for do it but i havent time for this. i try the next week .

[J_amb_o]

OBD possible after unlock in boot. On original tool of course.

[powertdi]

NOT Original yet :listen:

[javilette]

i dont try yet but you think that dont works galletto original whith this???

[powertdi]

I mean not original work also. :proud:

[sabahattincin]

continental simos pcr 2.1
clone FTech galletto2 help me ?

[cp2010]

continental simos pcr 2.1
clone FTech galletto2 help me ?

no,
some people say that is possible with mini galletto but i hear that this not working
only such "trick from seller" ;)