407 HDI 1.6 DPF OFF 2006MY

[Johnnyrb5]

Hi Everybody,

Can someone please help me remove DPF from this ECU manually.
I have tried incorrectly with ECUSAFE and all looked fine but car will not rev above 3000rpm no DTC in pp2000.
Many Thanks
J5

PS I removed dpf in pp2000 cust options and changed additive ECU to absent

[ZIZZOU]

try this and report

[Johnnyrb5]

Thank you zizzou will; try later today.
Is this a manual edit?
Thanks

[mbtun]

should be single switch solution.
hey G you still around? I though you are not around anymore?

[ZIZZOU]

let's tray,and repport for result johny

[Johnnyrb5]

Hi I wrote file and Engine ECU lost configuration and I have lost all injector codings.
I have added the settings best I can but some I am not sure of especially gearbox type and alternator class and body configuration can someone advise? I have to enter the codes for the injectors. Is cylinder 1 near the timing belt or the gearbox on this car? There also errors relating to FAP still. Car starts but only revs to 3000 rpm and dispalys engine management system faulty.
Pleaase help
J5

[Johnnyrb5]

Additional photo

[yas200]

Additional photo

Send #dtc. I can help you. No need sensor

[ZIZZOU]

hi
first,recode injectors,Ist cylinder 1 near the gearbox

[mbtun]

mr G brings bad luck :))

[barti122]

what is the number for the ecu

[barti122]

try this files first chec 407 1.6 fap off cheksum moj

[mbtun]

your file won't do any good. he lost car configuration and car must be recoded.

[ZIZZOU]

in 1.6HDI engine,i recode injectors in 10 minutes
http://img819.imageshack.us/img819/1391/injecteurt.jpg

[Johnnyrb5]

Thank you for your help.
Recoded injectors car running normally now :)

Car only has these errors. I told ecu I had topped up the additive level & replaced DPF, Can I remove connection to tank or just ignore as all seems fine now?

Engine ECU
Additive system Value received by CAN Incorrect
Additive system Quantity of additive to high
Additive system Fuel tank cap sensor
Additive system * Critical level of additive in the resovoir

[mario38]

I think that the files that you have tried are not good if you want to test my

[Johnnyrb5]

Mario38
I wrote your file
Recoded injectors and configuration for engine ecu
cleared faults
Went to BSI config and changed fuel to diesel without filter as I missed this before. cecked cust options petrol or diesel engine without filter. checked ecus present no additive ecu.
started fine no errors turned off found only errors as before
took for test drive ok for 10 minutes then depollution system faulty.
read codes now has additional code for turbo pressure to high. Would this cause the depollution error also?
J5

[ZIZZOU]

last week,i have donne chiptuning foe 207 1.6hdi from 110cv to 150cv with succes,cleint was very very happy
do you want to see your car fly johny?

[mario38]

Mario38
I wrote your file
Recoded injectors and configuration for engine ecu
cleared faults
Went to BSI config and changed fuel to diesel without filter as I missed this before. cecked cust options petrol or diesel engine without filter. checked ecus present no additive ecu.
started fine no errors turned off found only errors as before
took for test drive ok for 10 minutes then depollution system faulty.
read codes now has additional code for turbo pressure to high. Would this cause the depollution error also?
J5
this is strange I have other cars and 100% ok .. maybe your problem is writing file .. I advise you to bdm use

if you remember a thank you about the same

[Johnnyrb5]

Hi Mario,
yes I thought also I am using Galeto cable and software called "New Serial 1260" to write/read file.
Can you advise how to get BDM?
Thanks
J5

[kennfeld]

Hi Mario,
yes I thought also I am using Galeto cable and software called "New Serial 1260" to write/read file.
Can you advise how to get BDM?
Thanks
J5


your tool not read and recode the injectors ....
best is do it bdm if you have no good obd tool
i do them cmdflash never injector code lost ...