PDA

View Full Version : passat 2.0 edc 17cp 14 03L907309 dpf off



gadroulll
29th November, 2012, 08:01 PM
i need to remove this edc17c14 dpf.

i have two programs that do it .
can someone check them if it was done ok

i am sure that the files need correcting the checksums

titanium161 ,bdm100 , and winols15,mpps cannot do it


i have read the flash with abritus and it reads the 512kb , normally it should be 2048kb but its ok

Miketune
29th November, 2012, 11:04 PM
i need to remove this edc17c14 dpf.

i have two programs that do it .
can someone check them if it was done ok

i am sure that the files need correcting the checksums

titanium161 ,bdm100 , and winols15,mpps cannot do it


i have read the flash with abritus and it reads the 512kb , normally it should be 2048kb but its ok


hi friend,

see your file chsm correct

push thanks ;)

reggards

gadroulll
30th November, 2012, 07:24 PM
i try to write the file with mpps and i have message of wrong checksums.

i load the original and it writes

here are the file with the mpps

fargulkim
30th November, 2012, 08:06 PM
checksums ok

Miketune
30th November, 2012, 11:37 PM
i try to write the file with mpps and i have message of wrong checksums.

i load the original and it writes

here are the file with the mpps

see your file

gadroulll
3rd December, 2012, 08:40 PM
the files not worked for MPPS it found the checksum wrong and it stops i try to repair with the winols 224 but it also found them wrong .

here are the files i tested

pablo1971
3rd December, 2012, 11:15 PM
which mpps are you using....

gadroulll
3rd December, 2012, 11:23 PM
i use v12.01 but it loads the original file that works on the car

pablo1971
3rd December, 2012, 11:25 PM
i may be wrong...i tried to do one of these the other day...mpps v12-reads the edc17cp14....it will write back the original file.but the edc17cp14 has tuning protection,and it needs unlocking on the bench.

so if you mod a file it will still not write correctly....ecu needs bootmode.and tuning protection removing .then it can be read+write on obd.

gadroulll
3rd December, 2012, 11:47 PM
what tool do i need to do this .the mpps has the problem and not load the file , it stops at 75% . Also the original file looks to have 11checksums and not 10 checksums as winols says.
So i need a programmer that corrects the checksum in the written .

i have galletto1260 ,kwp2000 and mpps

J_amb_o
3rd December, 2012, 11:52 PM
None of them. You need X-17, CMD, etc.

Artilect
4th December, 2012, 12:07 AM
FGTech Galletto 2 clone will do this ECU OK.

You are brave to do EDC17 with Clone MPPS, at least you should have Boot mode readout first. You newer know.

BR

pablo1971
4th December, 2012, 12:23 AM
+1 fgtech2 is the tool for this,i havnt done one yet,but like artilect said.you need a boot read,esp as a back up....i did try a read with mpps v12...read all ok...did a read with fgtech2 and got a message---tuning protection-bootmode req-

gadroulll
4th December, 2012, 05:42 AM
it has been done with mpps . i read it . i need good checksum

gadroulll
6th December, 2012, 04:30 PM
the results are .\
the file was repasired with genius from dimsport for checksums .
the file was loaded with clone MPPS 12.01 IN THE CAR With ecu edc17cp14

the winols 224 do not repair the checksums it recognise it as med17

blade66
7th December, 2012, 02:13 AM
Send file i can do checksumme for your file ;)

furnata
7th December, 2012, 08:13 AM
Dont worry checksumm algo is the same for MED17 and EDC17.
I try to make Tiguan 2.0 tdi EDC17CP14 with FGtech 1led version but it cant write it- only write part with switch - but dont want to write part with postinjection (regeneration)maps if i change them
In the end i wrote it with K-Tag and everything is ok no need to correct chks.....

Uniqaz
12th December, 2012, 04:48 PM
Dont worry checksumm algo is the same for MED17 and EDC17.
I try to make Tiguan 2.0 tdi EDC17CP14 with FGtech 1led version but it cant write it- only write part with switch - but dont want to write part with postinjection (regeneration)maps if i change them
In the end i wrote it with K-Tag and everything is ok no need to correct chks.....
I read 2010 Passat 2.0 tdi EDC17CP14 with clone MPPS12, DPF swith off and the same file write back with FG mini with no problem ;)

pablo1971
12th December, 2012, 05:12 PM
has the ecu had the tp removed already from the ecu.

TheBadFrog
12th December, 2012, 05:43 PM
I have same ecu in my Passat.
Will try to read on weeken with new galletto 2 clone.
Can i read with OBD?
Or have i to take the ECU out of the car and try with bootmode (with opening the ECU?)


Another question how to reset Flash Attemps counter at this ECU?
Is it possible to set immo off? Then i can use a used ECU for tuning

Best regards

TheBadFrog

pablo1971
12th December, 2012, 06:00 PM
from what i no...and it aint alot...the ecu can be read by obd(mpps+fgtech2)and it can be write on obd but only write original.ecu has tuning protection and needs to be read on the bench in boot mode....tuning protection can then be removed from read...and then it can be written again and again in obd mode.....im sure someone will correct me if im wrong.

as for immob off,i dont think its possible yet.

gadroulll
12th December, 2012, 07:12 PM
mpps can write this ecu if you correct the checksums .

i have done dpf off this ecu and i have fault about lamba founds rich fuel.

how i can correct that or it is because of other cause of the car?

fargulkim
12th December, 2012, 08:42 PM
other reasons

pablo1971
12th December, 2012, 08:59 PM
what version of mpps was it.?????...



clone or original

J_amb_o
12th December, 2012, 11:14 PM
It will only write by MPPS if below TPROT 7, and you don't know until you have read the file if it has.

pablo1971
12th December, 2012, 11:23 PM
can you tell me were i must look in the dump to find the tprot

veloseeped
13th December, 2012, 12:04 AM
can you tell me were i must look in the dump to find the tprot

You can't see tprot version if you read it trough OBD.
It's only part of the full dump.

mouaoued
1st June, 2013, 10:32 PM
help Cheksum edc 17cp14 dtf off

Diagnosticated
2nd June, 2013, 06:54 AM
Question for experts. Is switch alone ok for dpf on these edc17 or must disable post injection also?