renault id46

[kari11]

Hello,

I bought a transponder ( ID:46 Chip for Renault (http://ecutool.com/Renault-ID46-Chip_6373.html) ). What can be taught to the car?
Renault Can Cilp and SBB key programmer not working.

Thanks
Kari

[sparkz02]

do you have pin? or you need pin?

[kari11]

do you have pin? or you need pin?


The pin has, but wrong type of transponder. There is only one key, and both should be.

[leandroks]

what model and year???

[kari11]

what model and year???

Renault Clio 1.4 2003 year.

[sexyceta]

Must be pre programmed first with z bull etc using dump from uch or use new remote

[alfabit]

Remote control key for central locking system 2 buttons or 1 button ?
If two buttons ID 46 ( it`s good that you bought ), if 1 button ID 33 ( not good for you that bought )

[kari11]

Remote control key for central locking system 2 buttons or 1 button ?
If two buttons ID 46 ( it`s good that you bought ), if 1 button ID 33 ( not good for you that bought )


Two buttons.

[kari11]

Must be pre programmed first with z bull etc using dump from uch or use new remote

Once you have a PIN, you can prepare transponder?

[alfabit]

Once you have a PIN, you can prepare transponder?

Of course, transponder precoded ( id correct, in your case 46 ),
can be done with ddt2000 - the simplest and cheapest tool for that job.

[coolsoda]

A standard PCF7936 Cipher-Manchester Transponder (ID46) cant be programmed to a Clio ,you need to use a Remote Key.

It is possible to use a PCF7936 but this must be produced from vehicle data

[ninja123]

if your car is 2003 clio, you should have a 1 button remote with pcf7946, not 2 button.

you need to precode pcf for remote to work, if not precoded, car will start but no remote.

Read eeprom from uch and post here for your pin, then use t300 to program.

ninja

[cristyand]

can anyone tell if sbb work on this car?

[keygargoil]

sbb will work on this car but only with a 7946 1 button remote key i make pcf7936 chips to these all the time but i write the chip into the dump with tango and it works if you programme it and the immo light is solid put some leads on and let it sit for 5 mins then switch the ignition on and it works

[kari11]

I teach this transponder to the car (ID:46 Chip for Renault (http://ecutool.com/Renault-ID46-Chip_6373.html))?
Or do I have to prepare transponder and teach?

[cristyand]

first you must prepare transponder then you teach it to the car.

[albertros]

If you don't prepare the pcf7946 the central locking won't work but the car will start.

[tawaf11]

pcf7946 not precode with zedbull our sbb in renault this type programme directly in canclip and car run

[tawaf11]

our frecquence deferant

[albertros]

pcf7946 not precode with zedbull our sbb in renault this type programme directly in canclip and car run
NOT SO
your key may have already been pre-coded but the replacement chips have not been pre-coded. The central locking will not work without writing pages P7 and P6 with zedbull or simular.

[kari11]

Thank you for all the comments.

[garryreed]

like others have said you cant program a carbon 46 to these must be a virgin micro chip transponder soldered on to the remote key then precoded and finally programmed.

[alunecosu]

What is coding for remote 2 butons pcf 7946.I need for (dacia logan remote)tnx

[alunecosu]

For another user with this problem.