PDA

View Full Version : Golf G60 Dump file please



benzgeek
11th January, 2013, 10:20 PM
Hello Mate's ,

i have Golf 2 16 V ,2.0 Turbo charged , i need ECU tuned dump so my engine can Rev to 7500RPM and to increase the boost pressure to 1.3 and work in a lower RON grade 90 .

thanks in advanced

pandokrator
11th January, 2013, 10:45 PM
boost under 1.5bar.

benzgeek
11th January, 2013, 10:54 PM
thank's mate for your fast replay i will try the dump now , would you please take alook ath the attached pictures for my car engine and ECU ,

pandokrator
12th January, 2013, 12:34 AM
all is the same my friend :-)
this map run well with 440cc/3bar injectors.
if you need more "preserves" maps i have all.
but ,best solution for this ecu and engine is a
experienced programmers who know exactly what he doing on the car in the street or on dyno.

benzgeek
12th January, 2013, 01:03 AM
i just write it to the ECU but i need to try it tomorrow , i wonder .... what stage is this dump ? my RON is 90 can it work good with it ? my injectors are green original G60@260CC
do you think i should change them ?

thanks alot

pandokrator
12th January, 2013, 10:37 AM
this dump is from limited edition golf II rallye 16VG60 engine (http://en.wikipedia.org/wiki/Volkswagen_Golf_Mk2#Golf_Limited). map it's made vw motorsport team.
if you need building map for your engine you can work with tunerproRT (http://www.tunerpro.net/download/SetupTunerProRT_v500_8040.exe) prog ( free ).
for that you need xdf file (work only with TunerProRTv.5) with right addresses.
here is that too.

for more than 1,0bar pressure suggest 440cc/3b injectors and 200kpa map sensor (inside ecu).

for 0,8~1.1bar pressure other evaluated file is that from sns tuning but need some settings for ignition advance.
personal i'm not content with this map.
mutch problems with idle.

benzgeek
12th January, 2013, 06:14 PM
i'm new with the tunning stuff , i will try your SNS dump now and report you .

thanks alot for your valueble support .

have a Great weekend

Benz Geek

pandokrator
12th January, 2013, 11:56 PM
good luck with your setup my friend.
check pm

pupsipu
13th January, 2013, 05:12 PM
your injectors are too small!!!!!

Don`t try wiht 1,3 bar!Your engine will be break...

Try bigger ijectors and search somebodxy who will help you with mapping...

regreds

benzgeek
13th January, 2013, 11:53 PM
i am running 0.7 bar now i will try to change the injector to 440 cc and try it, would you please provide me with bosch part number ? thanks

benzgeek
14th January, 2013, 12:24 AM
i have tried SNS Dump the car run really fast but it is not run well on ideal speed.

my transmission is manual 2.0 L/E9 Engine, and the map sensor is 200KPA.

i will try to get 440 CC injectors, any brand name suggestion?

thanks
Best regards
Benzgeek:ciao:

pandokrator
14th January, 2013, 08:00 AM
BOSCH 0280155968 42LB 440CC GREEN (http://www.aliexpress.com/store/product/High-performance-440cc-fuel-injector-0280150558-green-top-for-direct-sale/106657_440981195.html)

filecloud
14th January, 2013, 10:10 AM
i just write it to the ECU but i need to try it tomorrow , i wonder .... what stage is this dump ? my RON is 90 can it work good with it ? my injectors are green original G60@260CC
do you think i should change them ?

thanks alot
Hello
None of these maps will fit your setup. Original 1.816VG60 VW Motorsport is based on PL engine with lower compression pistons, standard 79mm pulley running 210PS and even less boost than the 8V due to to 16V cams overswing. 0,69bar measured live.
You need to change the pressure sensor to 250kPa minimum, re-calibrate ALL depending maps (quite a lot!), rescale all rpm dependend maps to go up to 7500rpm, change injectors, recalibrate software to them and to 2.0 liter, reshape the ignition maps to 9:1 compression rate from 9E Passat engine and much more.
This is no newbie project. This is for pros which can emulate these ecus live.

Go for a free,self adapting programmable ecu, change the injectors to sequential setup from batch firing, use a system with included boost control/throttle and a working knock control system which retards boost and ignition.
Digifant is only good for compressor setups, not for turbo.

greetings,
filecloud

pandokrator
15th January, 2013, 03:07 PM
yep , filecloud have absolutely right.
best solution for 16VT setup is a after market ecu.
This way can give safe & strong engine.
Digifant I is cheap solution.
bR

benzgeek
19th January, 2013, 12:14 AM
car is running well with SNS Dump and 0.7 boost bar, i will try injectors 440 CC and 1.0 bar boost and revert to you with the result.

Thanks
Best regards

pandokrator
19th January, 2013, 12:03 PM
same setup with sns map (0.8bar boost)
engine showed 227hp.
with 16VG60 (with very bad idle) showed 245hp with same boost.
with second map (that i sent you) 250kpa map sensor & modified air sensor (from g60 '92 model with throttle position and NOT switch)
engine give 247hp with 0.9b boost.
not so good idle,no good cold start,

all setups testing with 370cc injectors (i'm not sure but must be 0280150803 code) ,3bar/fuel and rs2 turbo.
original but NEW ,KR fuel pumps.
no one reconditioned engine is not the same.
hope your setup give's the best result :driver:

the best management system i have see in 16vt engines (http://www.boba-motoring.de/?knopf=markt)

benzgeek
9th February, 2013, 10:12 PM
thanks man , i just got my 440 CC injectors i will install them and test .

benzgeek
9th February, 2013, 11:03 PM
Hey mate , this is the injectors i got from Ebay .

Markopolo
10th February, 2013, 03:33 PM
This is hi or low impedence injectors?

Markopolo
10th February, 2013, 03:54 PM
Hey pandokrator this SNSg60turbo file is digi lag off?

benzgeek
8th March, 2013, 12:38 PM
i have tried boost 0.9 bar with 440 CC injectors map sensor is 200KPA / and damp file is limited edition g60 16V BBM , the result was amazing now i can call it turbo engine i still need to chage map sensor to 250 KPA and pistons to be able to try more boost, i will record video and show you the accelration.

Markopolo
27th April, 2014, 04:34 PM
Hi benzgeek,do you have the movie?

rsibiza
28th April, 2014, 05:49 PM
Hi, interestening threat :)

Does anybody have an G60 file,which has the modified custom code,wich is called NoDigiLag code??
This would be very helpfull;)

pandokrator
19th September, 2014, 08:44 PM
old answare but last days i spend my little free time for my fun car :joyous:
yes friend i have all files from old digifants ecus from g60.
anythink need i can share :top:
bR

digilag solution including on sns 16vt file.

bunkerking
8th January, 2024, 02:54 AM
@pandokrator - do you happen to have a 8v DF1 250kpa file?