BMW E39 synch EWS and dde not successed

[starprog]

hello!
I want to make synchronisation ews-dde , but adpatation not successed, I'm used BMW scanner PASOFT !
I get: ews-dde adaptation fail(e=ews1,dme4,dme5)
also I virginized ecu and writed isn on ews3!

car is bmw E39 year 2001
where is the problem please

[batpepi]

i make this with inpa and carsoft 6.1 software.was try too with scanner and not successful

[adiagnostyka]

i use inpa and always work

[starprog]

today I used inpa, but always same result, not successed alignement!!!!!!!!!!
error on dde: problem of engine immobiliser system (ews)!!!!
also, I changed 3 worked ews!
the engine cranck
where is the problem please?

[marek128]

check code line dde ews.
or you hawe not the same isn pass in ecu and ews.

[starprog]

I'm thinking to change ews3 to ews4, cause I already changed ews3 units 3 times!
I maked isn in ews3 too! but always not successed alignement ews/dde !!!
vin for this cars is: WBADL71030GV12209
I check that on realom, get infos that this car need ews 4.3 not ews3

who can confirm that please????
thanks

[bram380]

this car use ews3
you need to virgine dde.
after that realign dde-ews.

[starprog]

this car use ews3
you need to virgine dde.
after that realign dde-ews.
I have already virginized dde and transfered isn to ews then synchro...
but synchro not realised

[pepi]

Why dont you upload dumps from EWS and DDE, someone will help you.

[starprog]

I attached both dump for ews3 and dde.
the dde is original of the car, but ews3 was bought from second hand.
plese check and give dumps for make synchro!!!
thanks

[bram380]

try this dump:

[marek128]

Mate you hawe wrong fixed code.

Prog this to ews and do resync (NOW it will be working.):

Variable key reset, just in case if you been trying to start the emgine after You was reading the HC11 (EWS)

[starprog]

hello
I check the solution for bram and marek128 , synchro not successed!
I checked immo line wire between ews and dde, was ok
also can is ok?
I changed with other ecu, always same result!!!
only problem error on dde: Engine immobilser system (ews)!!!!
I thinked to make ews4 unit
what do u think????

[starprog]

who can give his solution here?

[digitaltech]

hello
I check the solution for bram and marek128 , synchro not successed!
I checked immo line wire between ews and dde, was ok
also can is ok?
I changed with other ecu, always same result!!!
only problem error on dde: Engine immobilser system (ews)!!!!
I thinked to make ews4 unit
what do u think????
dealer use ews4.3 replace all ews3 from 3/97

check ecu part number with dealer make sure it matchs, the only thing makes sense other then fault wiring,

1 other thing is to try run sync on table maybe.

[Min2xx]

who can give his solution here?
I have the same problem some time ago, use this dump for EWS and make sych with DDE with any BMW tool, Inpa can do this too.
PS DDE sych data in flash, not in eprom!!! Make all keys new!
PSW to PM

[starprog]

I get this error:
1640 dde .....
and synchro was ok
but car not start
who can explain me please what mean this dde error???

[Min2xx]

I get this error:
1640 dde .....
and synchro was ok
but car not start
who can explain me please what mean this dde error???
Write orig ECU eprom data and all will be ok!

[starprog]

hello for all who had helped me and specially to Min2xx (http://www.digital-kaos.co.uk/forums/members/79739-min2xx/), thx for all!!!
I have changed other ecu and car was started !!!!!!!!!!!!!!!!